Panasonic Dial Up Adapter Aw Du600p Operating Instructions

11
Connections
Menuj1 Function
Tx Rx Direct
Menuj5 Outputj1
RSj232C RSj422
When the settings are completed, press the 
key (i) once again to exit the menu
settings.
START2
MENU+
Receiving system connection procedure
1.
Connect the AW-PS301 AC adapter to the DC 12V IN
connector on this adapter.
3.Connect the telephone line to the line input jack on the
modem.
5.Set the power switch on the AW-DU600 to ON.
7.Set the power switch on the modem and the pan-tilt
head to ON.
8.“OK” appears on the LCD panel....

12
Connections
0123456789
1: Press Start Making a call
Make a call from the AW-DU600 of the transmitting
system.
2.Use the number keys on this adapter to enter the
desired number.
The telephone number entered appears on the top
section of the LCD panel.

While the telephone line is being connected, none of the
operating keys on the adapters will function except for
the STOP key on the transmitting side.
1.Turn on the power to all units.
3.After entering the telephone number, press the
START key.
When the...

13
Connections
$Direct mode
Control the pan-tilt head system directly using this adapter:1.
AW-DU600
AW-PS301
AW-CA50T29 (composite)
AW-CA50C29 (component)
AW-PH350
AW-PS300 10 Base-T cableConvertible camera 

14
Connections
Connection procedure
2(:): Up
8(;): Down
4(!): Left
6(#): Right
1 (TELE): Zoom in
7 (WIDE): Zoom out
3 (FAR): Focus (long-distance)
9 (NEAR): Focus (close-up)
5 (BAR): Color bar output
0 (CAM): Camera thru output
3Select the pan-tilt head system to be controlled.
Press the  key (i) to change
the menu setting item.
When “Menu-6 Output-2” appears on the LCD panel,
use the ! #keys and select
P1, P2, P3, P4 or P5.
STOPSTART
START2MENU+
When the settings are completed, press the  
key (i) once...

15
Connections
AW-DU600
Control
panelAW-PS301
AW-PS301AW-CA50T29
AW-PH350
AW-PS300 10 Base-T cableConvertible camera
AW-DU600AW-PS301 PC
AW-CA50T29 AW-CA50T9
AW-PH350
AW-PS300 10 Base-T cableConvertible camera
Control the pan-tilt head system using a control panel or PC:2.
Coaxial cable (5C-2V)
10Base-T cable

AW-RP605 cannot be used as the control panel with direct mode. 

16
Connections
2Select the connector for input of control signals from
the controller.
Press the  key (i) to change
the menu setting item.
“Menu-4 Input” appears on the LCD panel.
Select the CONTROL OUT connector to be used
using the ! #keys.
When control is to be performed from a control panel,
select RS-422 and select RS-232C when it is to be
performed from a PC.
STOPSTART
START2MENU+
When the settings are completed, press the 
key (i) once again to exit the menu
settings.
START2
MENU+
Menuj4 Input...

17
START
1
M12
M2
0
DEL
CAM 5
M5
TELE
3
M3
FA R
78
WIDE9
NEAR
4
M4
MENUCLEAR
STOP
MENU
RECALL
6
BAR
Menu settings
OPress the  key (i) and the first
menu item will appear on the LCD.
OPress the  key (i) while a menu
item is displayed on the LCD and the display will move to
the next item.
OPress the  key (i) again and the
last menu item will appear on the LCD.
OPress the  key (i) while a menu
item is displayed on the LCD and the display will move to
the previous item.
OUse the ! #keys to select the
setting...

18
Menu settings
$Dial memory
Menu-6 Output-2
(Initial setting: P1)This setting selects which pan-tilt head system is to be controlled by this adapter when this
adapter is in Direct mode.
The pan-tilt head system connected to the RS-232C or RS-422 P1 connector is
controlled. P1
P2
P3
P4
P5The pan-tilt head system connected to the RS-232C or RS-422 P2 connector is
controlled.
The pan-tilt head system connected to the RS-232C or RS-422 P3 connector is
controlled.
The pan-tilt head system connected to the...

19
Attaching the rack mounting adapters
Changing the position of the rear panel
To install the adapter in a rack, use the rack mounting adapters and four of the mounting screws (M4) supplied.
1. Remove the three screws from the bottom panel and
remove the blank panel.
2. Remove the three screws from the rear panel and
remove the rear panel.3. Use the three screws to firmly secure the rear panel
where the blank panel was removed from the bottom
panel.
Take care not to catch the internal wiring when...

20
Attaching the joint angle adapter
To attach the adapter to the controller, use the joint angle adapter, rack mounting adapter and mounting screws (M4 x 8)
supplied.
Rack mounting adapterScrew
Joint angle adapters