Panasonic Dial Up Adapter Aw Du600p Operating Instructions

							11
Connections
Menuj1 Function
Tx Rx Direct
Menuj5 Outputj1
RSj232C RSj422
When the settings are completed, press the 
key (i) once again to exit the menu
settings.
START2
MENU+
Receiving system connection procedure
1.
Connect the AW-PS301 AC adapter to the DC 12V IN
connector on this adapter.
3.Connect the telephone line to the line input jack on the
modem.
5.Set the power switch on the AW-DU600 to ON.
7.Set the power switch on the modem and the pan-tilt
head to ON.
8.“OK” appears on the LCD panel.
6.Dial Up Adapter settings
1Set this adapter to receive mode.
Press the  key (i) to open
the menu settings.
When “Menu-1 Function” appears on the LCD panel,
use the ! #keys and select
Rx (receive mode).
STOPSTART
START2MENU+
2Select the pan-tilt head system control.
Press the  key (i) to change
the menu setting item.
When “Menu-5 Output-1” appears on the LCD panel,
use the ! #keys and select
RS-2332C or RS-422 according to operating
conditions.
STOPSTART
START2MENU+
4.Connect the pan-tilt head to this adapter.
OIf the connection distance between this adapter and
the AW-PH300A pan-tilt-head is 10 m or less, use
the AW-CA28T9 (10 m) cable to connect the RS-
232C CONTROL OUT connector on this adapter to
the P/T CONTROL IN connector on the AW-PH300A.
OIf the connection distance between this adapter and
the AW-PH300A pan-tilt-head is more than 10 m, use
an RS-232C/RS-422 converter between the RS-422
CONTROL OUT connector on this adapter to the P/T
CONTROL IN connector on the AW-PH300A when
performing the connection.
OWhen the AW-PH350 pan-tilt-head is used, use a 10
BASE-T cable to connect the RS-422 CONTROL
OUT connector on this adapter to the CONTROL IN
IP/RP connector on the AW-PH350.
When an AW-RP301 or AW-RP501 is used as the
controller, connect the pan-tilt head to the P1
CONTROL OUT connector on this adapter.
2.Connect the TO MODEM connector to the RS-232C
connector on the modem using the RS-232C cable
provided with the modem.
Mode : Receiver
OK
Mode : Receiver
j jj
jj
j
If the modem is not connected correctly, [---] will appear
on the LCD panel. 
						

							12
Connections
0123456789
1: Press Start Making a call
Make a call from the AW-DU600 of the transmitting
system.
2.Use the number keys on this adapter to enter the
desired number.
The telephone number entered appears on the top
section of the LCD panel.

While the telephone line is being connected, none of the
operating keys on the adapters will function except for
the STOP key on the transmitting side.
1.Turn on the power to all units.
3.After entering the telephone number, press the
START key.
When the connection is initiated, “Calling” appears on
the LCD panel.
When the connection is established, “Connect” appears
on the LCD panel and control of the pan-tilt head
system from the control panel is possible.

The message appearing on the LCD panel may differ,
depending on the modem used.
4.Control the pan-tilt head system from the control
panel.  
When an AW-RP605 is being used as the control panel,
set the OPERATE switch to ON to control the pan-tilt
head system.

OWhen an AW-RP505 or AW-RP605 is being used as
the control panel, it is possible to switch the receiving
pan-tilt head system using the CONTROL button on
the control panel.
OIf the OPERATE switch on the AJ-RP605 is set to ON
before the telephone line is connected, “NO
CONNECT” is displayed on the LCD panel.
5.After control of the pan-tilt head is completed, press the
STOP key.
“Hang Up” appears on the LCD display and the
telephone line is cut.
Once the line is cut, “Press Start” appears on the LCD
panel.
When ON has been selected for the “Menu-7 Pw-Off”
setting, the power to the pan-tilt head will turn off at the
same time as the telephone line is cut.  When OFF has
been selected for the “Menu-7 Pw-Off” setting, the
power to the pan-tilt head will remain on when the
telephone line is cut.

If the POWER switch or OPERATE switch on the
control panel is set to OFF before the telephone line is
cut, the power to the pan-tilt head will turn off regardless
of the “Menu-7 Pw-Off” setting. If the wrong number is entered by mistake, press the
DELETE key (i) to delete 1 digit at a time,
starting from the number entered last. Press the CLEAR
key (i) to delete the whole number at
once.
START#
0#
!Telephone number entered 
						

							13
Connections
$Direct mode
Control the pan-tilt head system directly using this adapter:1.
AW-DU600
AW-PS301
AW-CA50T29 (composite)
AW-CA50C29 (component)
AW-PH350
AW-PS300 10 Base-T cableConvertible camera 
						

							14
Connections
Connection procedure
2(:): Up
8(;): Down
4(!): Left
6(#): Right
1 (TELE): Zoom in
7 (WIDE): Zoom out
3 (FAR): Focus (long-distance)
9 (NEAR): Focus (close-up)
5 (BAR): Color bar output
0 (CAM): Camera thru output
3Select the pan-tilt head system to be controlled.
Press the  key (i) to change
the menu setting item.
When “Menu-6 Output-2” appears on the LCD panel,
use the ! #keys and select
P1, P2, P3, P4 or P5.
STOPSTART
START2MENU+
When the settings are completed, press the  
key (i) once again to exit the menu
settings.
START2
MENU+
START
1M12M2
0DEL
CAM
5M5
TELE3M3
FA R
78WIDE9NEAR
4M4MENU
CLEARSTOP
MENURECALL
6
BAR
4.When the settings are completed, turn the power of the
AW-DU600 off and then back on again.
The power of the pan-tilt-head system turns on and
operation is possible.
5.The pan-tilt head system can be controlled in the
following ways using the operating keys on this adapter.
Menuj6 Output-2
P1 P2 P3 P4 P5
2Set the CONTROL OUT connector according to the
type of pan-tilt connected and the connection
distance.
Press the  key (i) to change
the menu setting item.
When “Menu-5 Output-1” appears on the LCD panel,
use the ! #keys and select
RS-2332C or RS-422 according to the pan-tilt head
system to be connected.
STOPSTART
START2MENU+
1.Connect the pan-tilt head system to the CONTROL
OUT connector on this adapter.
2.Turn on the power to this adapter and the pan-tilt head
system.
3.Dial Up Adapter settings
1Set this adapter to direct mode.
Press the  key (i) to open
the menu settings.
When “Menu-1 Function” appears on the LCD panel,
use the ! #keys and select
Direct (direct mode).
STOPSTART
START2MENU+
Menuj1 Function
Tx Rx Direct
Menuj5 Output-1
RSj232C RSj422 
						

							15
Connections
AW-DU600
Control
panelAW-PS301
AW-PS301AW-CA50T29
AW-PH350
AW-PS300 10 Base-T cableConvertible camera
AW-DU600AW-PS301 PC
AW-CA50T29 AW-CA50T9
AW-PH350
AW-PS300 10 Base-T cableConvertible camera
Control the pan-tilt head system using a control panel or PC:2.
Coaxial cable (5C-2V)
10Base-T cable

AW-RP605 cannot be used as the control panel with direct mode. 
						

							16
Connections
2Select the connector for input of control signals from
the controller.
Press the  key (i) to change
the menu setting item.
“Menu-4 Input” appears on the LCD panel.
Select the CONTROL OUT connector to be used
using the ! #keys.
When control is to be performed from a control panel,
select RS-422 and select RS-232C when it is to be
performed from a PC.
STOPSTART
START2MENU+
When the settings are completed, press the 
key (i) once again to exit the menu
settings.
START2
MENU+
Menuj4 Input
RSj232C RSj422
3Set the CONTROL OUT connector according to the
type of pan-tilt connected and the connection
distance.
Press the  key (i) to change
the menu setting item.
When “Menu-5 Output-1” appears on the LCD panel,
use the ! #keys and select
RS-232C or RS-422 according to the pan-tilt head
system to be connected.
STOPSTART
START2MENU+
7. 6.Set the power switch on the pan-tilt head to ON.
8.Set the POWER switch on the control panel to ON to
control the pan-tilt head system. When an AW-RP505 is
being used as the control panel, select the pan-tilt head
system using the CONTROL button on the control
panel.
9.When the POWER switch on the control panel is set to
OFF after control of the pan-tilt head is completed, the
power of pan-tilt head system will turn off.
Connection procedure
1.
Connect the AW-PS301 AC adapter to the DC 12V IN
connector on this adapter.
2.Set the control panel selector switch on this adapter to
B.
5.Dial Up Adapter settings
1Set this adapter to direct mode.
Press the  key (i) to open
the menu settings.
When “Menu-1 Function” appears on the LCD panel,
use the ! #keys and select
Direct (direct mode).
STOPSTART
START2MENU+
Menuj1 Function
Tx Rx Direct
Menuj5 Output-1
RSj232C RSj422 3.
1Connect the PAN/TILT CONTROL OUT connector
on the control panel to the PAN/TILT CONTROL IN
connector on this adapter using a 10 BASE-T
(equivalent to UTP category 5) straight cable.
The connection distance can be extended up to 500
meters.
2Connect the CAMERA CONTROL OUT connector on
the control panel to the CAMERA CONTROL IN
connector on this adapter using a coaxial cable
(equivalent to 5C-2V).
The connection distance can be extended up to 500
meters.

This connection is not possible with the AW-RP301
control panel as it is not equipped with a CAMERA
CONTROL OUT connector.
3When a PC is used as the control panel, connect it to
the TO RCB/PC connector on this adapter.
4.Set the power switch on this adapter to ON. 
						

							17
START
1
M12
M2
0
DEL
CAM 5
M5
TELE
3
M3
FA R
78
WIDE9
NEAR
4
M4
MENUCLEAR
STOP
MENU
RECALL
6
BAR
Menu settings
OPress the  key (i) and the first
menu item will appear on the LCD.
OPress the  key (i) while a menu
item is displayed on the LCD and the display will move to
the next item.
OPress the  key (i) again and the
last menu item will appear on the LCD.
OPress the  key (i) while a menu
item is displayed on the LCD and the display will move to
the previous item.
OUse the ! #keys to select the
setting for each menu item.
STOPSTART
STOP2MENUj
START2MENU+
START2MENU+
START2MENU+
$How to perform menu settings
$Menu items
Menu-1 Function
(Initial setting: Tx)Dial up adapter mode settings
Telephone line settings
This is when the telephone line to be used is a tone line. Tone
Pulse
External line transmission number settings
None
0 and
9 andThis is when the telephone line to be used is a pulse line.
This is for when an external line transmission number is not required.
This is for when 0 is to be transmitted via a PBX.
This is for when 9 is to be transmitted via a PBX. This is for when this adapter is to be used as the transmitting system. Tx
Rx
DirectThis is for when this adapter is to be used as the receiving system.
This is for when this adapter is to be used in direct mode (i.e. when a
telephone line is not to be used).
Menu-2 Modulate
(Initial setting: Tone)
Menu-3 PBX
(Initial setting: None)
The following items are only displayed when this adapter is in Tx mode.
Yes
No Power control setting for the pan-tilt head system when the telephone line is cut
The power of the pan-tilt head system turns off when the line is cut.
The power of the pan-tilt head system does not turn off when the line is cut. Menu-7 Pw-off
(Initial setting: Yes) 
						

							18
Menu settings
$Dial memory
Menu-6 Output-2
(Initial setting: P1)This setting selects which pan-tilt head system is to be controlled by this adapter when this
adapter is in Direct mode.
The pan-tilt head system connected to the RS-232C or RS-422 P1 connector is
controlled. P1
P2
P3
P4
P5The pan-tilt head system connected to the RS-232C or RS-422 P2 connector is
controlled.
The pan-tilt head system connected to the RS-232C or RS-422 P3 connector is
controlled.
The pan-tilt head system connected to the RS-232C or RS-422 P4 connector is
controlled.
The pan-tilt head system connected to the RS-232C or RS-422 P5 connector is
controlled.
This adapter’s dial memory function enables up to 5 specific
telephone numbers to be stored.
ORegistering a telephone number
1. Enter the number using the operating keys on this
adapter.
2. While pressing the  key, press one of the dial memory
registration keys from  (M1) through  (M5) into
which the number is to be entered.
3. “Writing Memory 2” (2is the dial memory number)
appears on the LCD panel and the telephone number is
stored.
51
#
OUsing a dial memory to make a call
1. Press the  key (i).
2. The dial memory number (M1 to M5) entered appears on
the LCD panel.
If a telephone numbers has not been registered for the
dial memory number, the LCD panel display will be blank.
3. Each time the  key (i) is
pressed, the dial memory number is switched.
4. Press the  key to initiate the connection.
START
STOP#RECALL
STOP#RECALL
This setting selects which connector is to be used for the controller when this adapter is in Direct mode.
TO RCB/PC connector (PC used for control)
PAN/TILT CONTROL IN connector (control panel used for control) RS-232C
RS-422
This setting selects which connectors are to be used for the pan-tilt head systems.
The RS-232C CONTROL OUT connectors are used.
The RS-422 connectors cannot be used in conjunction with these
connectors.
The RS-422 CONTROL OUT connectors are used.
The RS-232C connectors cannot be used in conjunction with these
connectors. RS-232C
RS-422 Menu-4 Input
(Initial setting:RS-232C)
Menu-5 Output-1
(Initial setting: RS-422)
The following items are only displayed when this adapter is in Direct mode
The following item is only displayed when this adapter is in Rx mode or Direct mode
OErasing a dial memory
1. Press the  key (i) to erase the
number displayed on the LCD panel.
2. While pressing the  key, press one of the dial memory
registration keys from  (M1) through  (M5) which is
to be erased.
3. “Writing Memory 2” (2is the dial memory number)
appears on the LCD panel and the telephone number is
erased.
51
#
START#CLEAR 
						

							19
Attaching the rack mounting adapters
Changing the position of the rear panel
To install the adapter in a rack, use the rack mounting adapters and four of the mounting screws (M4) supplied.
1. Remove the three screws from the bottom panel and
remove the blank panel.
2. Remove the three screws from the rear panel and
remove the rear panel.3. Use the three screws to firmly secure the rear panel
where the blank panel was removed from the bottom
panel.
Take care not to catch the internal wiring when reattaching the panels.
RS-232C CONTROL OUT
P5 P4 P3 P2 P1
P5 P4 P3 P2 PAN/TILT
CONTROL INCAMERA
CONTROL INGND DC 12V IN TO RCB/PC
A
B
P1TO CAMERA & PAN/TILT HEAD TO MODEM
RS-422 CONTROL OUTTO CAMERA & PAN/TILT HEADTO CONTROL PANEL
OUT PUT
IN PUT
4. Use the three screws to firmly secure the blank panel
where the rear panel was removed.
RS-232C CONTROL OUT
P5 P4 P3 P2 P1
P5 P4 P3 P2 PAN/TILT
CONTROL INCAMERA
CONTROL INGND DC 12V IN TO RCB/PC
A
B
P1TO CAMERA & PAN/TILT HEAD TO MODEM
RS-422 CONTROL OUTTO CAMERA & PAN/TILT HEADTO CONTROL PANEL
OUT PUT
IN PUT
Screws
ScrewsScrews
Screws Blank panel
Blank panel Rack mounting adapterScrew 
						

							20
Attaching the joint angle adapter
To attach the adapter to the controller, use the joint angle adapter, rack mounting adapter and mounting screws (M4 x 8)
supplied.
Rack mounting adapterScrew
Joint angle adapters