Panasonic Cwxc65hu Operating Instructions Manual

							Please read these operating instructions thoroughly
before using your air conditioner and keep for future reference.
For U.S customers :
For assistance, please call : 1-800-211-PANA(7262) or 
Register your product at : http://www.panasonic.com/register
INSTALLATION AND OPERATING INSTRUCTIONS
Room Air Conditioner
Models:CW-XC65HU, CW-XC85HU
CW382820391N
R 
						

							2
Safety Precautions
About the Controls on the Air Conditioner
Features and Installation
Before you call for service...
FOR YOUR RECORDS
Staple your receipt to this page in case you need it later.
Write down the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of each unit.
Dealers Name
Date Purchased
Inside you will find many helpful hints on how to use and
maintain your air conditioner properly. Just a little preventive
care on your part can save you a great deal of time and
money over the life of your air conditioner.
Youll find many answers to common problems in the chart
of troubleshooting tips. If you review our chart of
Troubleshooting Tipsfirst, you may not need to call for
service at all.
READ THIS MANUAL
CAUTION
• Contact an authorized Service technician for repair or
maintenance of this unit.
• The air conditioner is not intended for use by young
children or infirm persons without supervision.
• Young children should be supervised to ensure that they
do not play with the air conditioner.
Safety Precautions
Safety Precautions .............3
About the Controls on
the Air Conditioner
Controls ..............................5
Remote Controller ..............6
Ventilation ..........................7
Air Direction........................7
How to Secure Drain Pipe....7
Care and Maintenance 
Air Filter Cleaning...............8
Features
Features .............................9
Installation
How to Install the Unit ......10
Window Requirements .....10
Installation Kit Contents ...11
Suggested Tool
Requirements ...................11
Cabinet Installation...........12
Electrical Data ..................14
Electrical Safety ...............15
Before you call for
service...
Normal Operation .............16
Abnormal Operation .........16 
						

							WARNING
3
Safety PrecautionsSafety Precautions 
To prevent injury to the user or other people and property damage, the following instructions must be
followed.
Incorrect operation due to ignoring of instruction will cause harm or damage. The seriousness is classified
by the following indications.
WARNING: This symbol indicates the possibility of death or serious injury.
CAUTION:This symbol indicates the possibility of injury or damage to
property only.
Meanings of symbols used in this manual are as shown below.
Be sure not to do this.
Be sure to follow the instructions.
Plug in the power plug
properly.
• Otherwise, it will cause electric
shock or fire due to heat
generation.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
• It will cause electric shock or fire
due to heat generation.
Do not damage or use an
unspecified power cord.
• It will cause electric shock or fire.
• 
If the power cord is damaged, it must
be replaced by the manufacturer or
an authorized service center or a
similarly qualified person in order to
avoid a hazard.
Do not modify power cord
length or share the outlet
with other appliances.
• It will cause electric shock or fire
due to heat generation.
Do not operate with wet
hands or in a damp
environment.
• It will cause electric shock.
Do not direct air flow at room
occupants.
• This could lead to health
problems. 
						

							4
Safety Precautions
When the air filter is to be
removed, do not touch the
metal parts of the unit.
• It may cause an injury.
Do not clean the air
conditioner with water.
• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Ventilate well when used
together with a stove, etc.
• An oxygen shortage may occur.
When the unit is to be
cleaned, switch off, and turn
off the breaker.
• Since the fan rotates at high
speed during operation, it may
cause an injury.
Do not put a pet or house
plant where it will be exposed
to direct air flow.
• This could injure the pets or
plants.
Do not use for special
purposes.
• Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects. 
It may cause deterioration of
quality, etc.
Do not operate switches 
with wet hands
.
• It may cause an electric shock.
Do not apply an insecticide 
or flammable spray.
• It may cause a fire or deformation
of the cabinet.
Do not put a heater, etc.
where it is exposed to direct
air flow.
•It may cause imperfect
combustion. 
						

							5
About the Controls on the Air Conditioner
Model: CW-XC85HU Model: CW-XC65HU
TIMERFA N ECONOMYCOOL
DRY
TIMER TIMERMODE
MODEOFF/ON
FA N
SPEED
AIR
SWINGAIR
SWING
F
hr
4
1
6
7
325
OPERATION
TEMP
TIMERAIR
SWINGAIR
SWINGFA N ECONOMYCOOL
DRY
TIMER TIMERMODE
MODEOFF/ON
F
hr
FA N
SPEED4
1
7
325
OPERATION
TEMP
Controls
OPERATION
• To turn the air conditioner ON, push the
OFF/ON button.
To turn the air conditioner OFF, push the
button again.
• This button takes priority over any other
buttons.
• When you first turn it on, the air conditioner
is on the High cool mode and the
temperature is set at 72°F (22°C)
MODE
• Every time you push this button, it will
toggle between COOL,ECONOMY, FAN
and DRY.
ON/OFF TIMER
• Every time you push the TIMER button,
timer is set as follows. (1Hour 2Hours 
3Hours 4Hours 5Hours 6Hours 
7Hours 8Hours 9Hours 10Hours 
11Hours 12Hours O)
• The Setting Temperature will be raised by
2°F(1˚C) 30 min. later and by 2°F(1˚C) after
another 30 min.
FAN SPEED
• Every time you push this button it is set as
follows. {High(F3) Low(F1) Med(F2) 
High(F3)...}.
TEMPERATURE SETTING
• This button can automatically control the
temperature of the room. The temperature can
be set within a range of 60°F to 86°F by 1°F
(16˚C to 30˚C by 1˚C) Select a lower number for
a lower temperature in the room.
AIR SWING
• This button can automatically control the air flow
direction.
REMOTE CONTROL SIGNAL RECEIVER
About the Controls on the Air Conditioner 
						

							6
About the Controls on the Air Conditioner
OPERATION
TEMP
TIMERAIR
SWING
MODE
ECONOMYFAN SPEED1
3
24
6
5
7
OPERATION
TEMP
TIMER
MODE
ECONOMYFAN SPEED1
3
24
6
5
Model: CW-XC85HU Model: CW-XC65HU
Remote controller
OPERATION
• To turn the air conditioner ON, push the button. 
To turn the air conditioner OFF, push the button
again.
• This button takes priority over any other buttons.
• When you first turn it on, the air conditioner is on
the High cool mode and the temp. at 72°F (22˚C).
MODE
• Every time you push this button,it will toggle
between COOL, ECONOMY, FAN and DRY.
ON/OFF TIMER
- STOPPING OPERATION
• Every time you push this button,  when the air
conditioner is operating, timer is set as follows.
(1Hour 2Hours 3Hours 4Hours 5Hours
6Hours 7Hours 8Hours 9Hours 
10Hours 11Hours 12Hours O)
• The Setting Temperature will be raised by 
2°F (1°C) 30 min. later and by 2°F (1°C) after
another 30 min.
- STARTING OPERATION
• Every time you push this button, when the air
conditioner is not operating, timer is set as follows.
(1Hour 2Hours 3Hours 4Hours 5Hours
6Hours 7Hours 8Hours 9Hours 
10Hours 11Hours 12Hours O)
FAN SPEED
• Every time you push this button it is set as follows.
{High(F3) Low(F1) Med(F2) High(F3)...}.
TEMPERATURE SETTING
• This button can automatically control the
temperature of the room. 
The temperature can be set within a range of 60°F
to 86°F by 2°F.(16˚C to 30˚C by 1˚C) Select the
lower number for lower temperature of the room.
ECONOMY
• If the switch is set to On, the fan stops when the
compressor stops cooling. Approximately every 3
minutes the fan will turn on and check the room air
to determine if cooling is needed.
AIR SWING
• This button can automatically control the air flow
direction.
DRY
• When this unit is in dry mode, the fan rotates in
low speed. The fan stops when the compressor
stops cooling.
Approximately every 3 minutes the fan will turn on
and the unit checks the room air temperature to
set itself.
Precaution:The Remote Controller will not function properly if strong light strikes the sensor window of the
air conditioner or if there are obstacles between the Remote Controller and the air conditioner. 
						

							7
About the Controls on the Air Conditioner
VENT CLOSE
OPEN
Par tA
Par tB
Drain pipe
Drain cap
Fig. 4 Fig. 3
Fig. 2
DRAIN
PA NDRAIN HOSE
Inside diameter 17mm (5/8)
Fig. 1
CABINET
SCREW
Controlled
manuallyControlled
manuallyControlled by Remote
Controller (Model: CW-XC85HU)
O
F
F
/
O
NO
P
ER
A
T
I
O
NTEMP/TIMERC
O
O
L
F
A
N
H
I
G
H
M
E
D
L
O
WM
O
D
E
F
A
N 
S
P
E
E
DSETT
I
MERS
E
T
/
C
A
N
C
E
LA
I
R 
S
W
I
N
GECONOMYh
r FW
i
re
l
e
s
sR
e
m
o
t
e
 C
o
n
t
ro
l
Remove therubber plug
O
F
F/
O
NO
P
E
R
A
T
I
O
NT
E
P
/T
IC
O
O
L
F
A
N
H
I
G
H
M
E
D
L
O
WM
O
E
F
A
N
 
S
P
E
E
DS
ETTIMERS
E
T
/
C
N
EA
I
R
 ECONOMYFW
ir
e
l
e
s
sR
em
o
te
 
C
o
n
t
r
o
l
Additional controls and important information.
Ventilation
The ventilation lever must be in the CLOSE position in order to maintain the best
cooling conditions. When fresh air is necessary in the room, set the ventilation
lever to the OPEN position. 
The damper is opened and room air is drawn out.
NOTE:Before using the ventilation feature, and prior to installing the front grille,
pull down part 
until level with part .
Air Direction
The vertical air direction is adjusted by
rotating the horizontal louver forward or
backward manually.The horizontal air direction is adjusted by rotating
the vertical louver right or left manually or by
Remote Controller. The direction of air can be controlled wherever you want to cool by adjusting the horizontal
louver and the vertical louver.
•VERTICAL AIR-DIRECTION CONTROL•HORIZONTAL AIR-DIRECTION CONTROL
How to Secure the Drain Pipe
In humid weather, excess water may cause the BASE PAN to overflow. To drain the water, remove the
DRAIN CAP and secure the DRAIN PIPE to the rear hole of the BASE PAN. Press the drain pipe into the
hole by pushing down and away from the fins to avoid injury.(See Fig.1)
Optional(CW3H02502C)
1. Remove the rubber plug and slide the chassis out
from the cabinet.(See Fig. 2)
2. Install the drain pan over the corner of the cabinet
where you removed the plug with 4 (or 2)
screws.(See Fig. 3)
3. Connect the drain hose to the outlet located at the
bottom of the drain pan. You can purchase the drain
hose or tubing locally to satisfy your particular
needs. (Drain hose is not supplied).(See Fig. 3)
4. Select the most appropriate connection from among
the figures to the right (by considering the hole of the
unit) to fit drain pan to your own unit.(See Fig. 3)
5. Slide the chassis back into the cabinet. Reinstall the
cabinet screws. Secure the cabinet to chassis by
using screws. (See Fig. 4) 
						

							8
About the Controls on the Air Conditioner
Air Filter Cleaning
The air filter behind the front grille should be checked and cleaned at least once every 2
weeks or more often if necessary.
TO REMOVE: 
1. Open the inlet grille upward by pulling out the bottom of the inlet grille or downward by
pulling out the top of the inlet grille.
2. Using the tab, pull up slightly on the filter to release it and pull it down or up.
3. Clean the filter with warm, soapy water under 40°C (104°F).
4. Rinse and gently shake the water from the filter and let it dry before replacing it.
CAUTION:DO NOT operate the air conditioner without a filter because dirt and lint will
clog it and reduce performance.
How to Insert Batteries
Care and Maintenance
TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.
1.Remove the cover from the back of
the remote controller.
2.Insert two AAA dry cell batteries.
• Be sure that the (+) and (-)
directions are correct.
• Be sure that both batteries are
new.
3.Re-attach the cover.• Do not use rechargeable
batteries. Such batteries 
differ from standard dry cells in
shape, dimensions, and
performance.
• Remove the batteries from the
remote controller if the air
conditioner is not going to be
used for an extended length of
time.
• Keep the remote control away
from infants and small children to
prevent them from accidentally
swallowing the batteries. 
						

							9
Features and Installation
Learning parts name prior to installation will help you understand the installation procedure.
Features
Features
CABINET
FRONT GRILLE
AIR FILTER
AIR INTAKE
(INLET GRILLE) AIR DISCHARGE HORIZONTAL AIR DEFLECTOR
(VERTICAL LOUVER) VERTICAL AIR DEFLECTOR
(HORIZONTAL LOUVER)
EVAPORATOR
POWER CORD BASE PAN CONDENSER COMPRESSOR BRACE
CONTROL BOARD
EVAPORATOR
POWER CORD BASE PAN CONDENSER COMPRESSOR BRACE
CONTROL BOARD
REMOTE CONTROLLERVERTICAL LOUVER
Model: CW-XC85HU
Model: CW-XC65HU
REMOTE CONTROLLER
FAN
ECONOMY
COOL
DRYTIMERTIMER
TIMERMODE
MODEO
F
F
/
O
N
F
h
rFAN
SPEED
AIR
SWING AIR
SWING
FAN
ECONOMYCOOL
DRYTIMERTIMER
TIMERMODE
MODEO
F
F
/
O
N
F
h
rFA N
SPEED 
						

							10
Features and Installation
About 12.7 mm (1/2)
76.2 cm (30)~
152.4 cm (60)
Awning
Cooled airFence
Over 50.8 cm (20)
Heat 
radiation
55.8 cm (22) to
91.44 cm (36)
Offset12.7 mm (1/2) to
31.8 mm (11/4)
Sill
Exterior
Interior wall
47 cm (181/2) min.(Without frame curtain)
Stool38 cm (15) min
(With frame curtain)
INSTALLATION
1. To prevent vibration and noise, make sure
the unit is installed securely and firmly
2. Install the unit where the sunlight does not
shine directly on the unit.
3. The outside of the cabinet must extend
outward for at least 28 cm (11) and there
should be no obstacles, such as a fence or
wall, within 50.8 cm (20) from the back of
the cabinet because it will prevent heat
radiation of the condenser.
Restriction of outside air will greatly reduce
the cooling efficiency of the air conditioner.
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the
structure.
4. Install the unit a little slanted so the back is slightly lower than the front 
(about 12.7 mm (
1/2)).
This will force condensed water to flow to the outside.
5. Install the unit with the bottom about 76.2 cm (30)~152.4 cm (60) above the floor level.
Window Requirements
NOTE: All supporting parts should be secured to firm wood, masonry, or metal.
This unit is designed for installation in
standard double hung windows with actual
opening widths from 55.88 cm (22) to 91.44
cm (36).
The top and bottom window sash must open
sufficiently to allow a clear vertical opening of
38 cm (15) from the bottom of the upper
sash to the window stool.
How to Install the Unit