Panasonic Compact Stereo System Sc-hc57 Owners Manual

							RQT9708-2P
ESPAÑOL
ENGLISH
until 
2011/12/26
Owner’s Manual
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Please keep this manual for future reference.
If you have any questions, contact:
U.S.A. and Puerto Rico: 1-800-211-PANA (7262)
Canada: 1-800-561-5505
Compact Stereo System
Model No. SC-HC57
Included Installation Instructions (>2, 6)The installation should never be done by any other than a qualified installation specialist.
Before commencing work, carefully read these  installation instructions and the operating 
instructions to ensure that installation is performed correctly.
(Please keep these instructions. You may need t hem when maintaining or moving this unit.)
La referencia rápida en español se puede encontrar en la página 20-21.
 
PPC
SC-HC57~RQT9708.book  1 ページ  ２０１２年４月１７日　火曜日　午後５時３６分 
						

							2
RQT9708
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety 
instructions listed below. Keep these operating instructions handy for future reference.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in 
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, 
heat registers, stoves, or other apparatus (including 
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or 
grounding-type plug. A polarized plug has two blades with 
one wider than the other. A grounding-type plug has two 
blades and a third grounding prong. The wide blade or the 
third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the 
manufacturer.
12 Use only with the cart, stand, tripod, 
bracket, or table specified by the 
manufacturer, or sold with the 
apparatus. When a cart is used, use 
caution when moving the cart/apparatus 
combination to avoid injury from 
tip-over.
13 Unplug this apparatus during lightning storms or when 
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing 
is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.
Unit≥To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or 
splashing.
– Do not place objects filled with liquids, such as vases, on 
this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to 
qualified service personnel.
Power cord≥Install this unit so that the power cord can be unplugged from 
the socket outlet immediately if any problem occurs.
Button-type battery (Lithium battery)≥Risk of fire, explosion and burns. Do not disassemble, heat 
above 60oC (140oF) or incinerate.
Unit≥This unit utilizes a laser. Use of controls or adjustments or 
performance of procedures other than those specified herein 
may result in hazardous radiation exposure.
≥Do not place sources of naked flames, such as lighted 
candles, on this unit.
Placement≥To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in 
cabinet or in another confined space. Ensure this unit is 
well ventilated.
– Do not obstruct this unit’s ventilation openings with 
newspapers, tablecloths, curtains, and similar items.
Button-type battery (Lithium battery)≥Danger of explosion if battery is incorrectly replaced. 
Replace only with the type recommended by the 
manufacturer.
≥When disposing the batteries, please contact your local 
authorities or dealer and ask for the correct method of 
disposal.
≥Keep out of reach of children.
≥Insert with poles aligned.
≥Mishandling of batteries can cause electrolyte leakage and 
may cause a fire.
– Remove batteries if you do not intend to use the remote 
control for a long period of time. Store in a cool, dark 
place.
– Do not heat or expose to flame.
– Do not leave the battery(ies) in a car exposed to direct 
sunlight for a long period of time with doors and windows 
closed.
– Do not touch the terminals (i and j) with metal objects.
– Do not recharge, disassemble, remodel, heat or throw into 
fire.
WARNING
If any electrolyte should come into contact with your hands 
or clothes, wash it off thoroughly with water.
If any electrolyte should come into contact with your eyes, 
never rub the eyes. Rinse eyes thoroughly with water, and 
then consult a doctor.

This product contains a CR Coin Cell Lithium 
Battery which contains Perchlorate Material s 
special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/
perchlorate.
CAUTION
SC-HC57~RQT9708.book  2 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							3
RQT9708
ENGLISH
AccessoriesTHE FOLLOWING APPLIES ONLY IN THE 
U.S.A.
FCC Note:
This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to Part 15 of 
the FCC Rules.
These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful 
interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or 
more of the following measures:
≥Reorient or relocate the receiving antenna.
≥Increase the separation between the equipment and 
receiver.
≥Connect the equipment into an outlet on a circuit 
different from that to which the receiver is connected.
≥Consult the dealer or an experienced radio/TV 
technician for help.
Any unauthorized changes or modifications to this 
equipment would void the user’s authority to operate this 
device.
This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, 
including interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Marketing Company of 
North America
Telephone No.: 1-800-211-PANA (7262)
The lightning flash with arrowhead symbol, within an 
equilateral triangle, is intended to alert the user to the 
presence of uninsulated “dangerous voltage” within 
the product’s enclosure that may be of sufficient 
magnitude to constitute a risk of electric shock to persons.
CAUTION
CAUTION :TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is 
intended to alert the user to the presence of important 
operating and maintenance (servicing) instructions in 
the literature accompanying the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Check the supplied accessories before using this 
unit.
∏1 Remote control 
(with a battery)
(N2QAYC000056)
∏1 AC power supply 
cord
(K2CB2YY00059)∏1 FM indoor 
antenna 
(RSAX0002)
Wall mounting accessories
∏1 Safety holder
(RGQ0660-K)
∏1 Screw 
(XTB3i8JFJK)∏2 Wall mount 
brackets
(RMQX1082-K)
(ONLY FOR CANADA)
The enclosed Canadian French label sheet corresponds to the 
English display on the top of the unit.
	≥Do not use AC power supply cord with other equipment.
≥Product numbers provided in this Owner’s Manual are 
correct as of December 2011. These may be subject to 
change.
THE FOLLOWING APPLIES IN THE U.S.A. 
AND CANADA
This device complies with Part 15 of FCC Rules and RSS-Gen 
of IC Rules.
Operation is subject to the following two conditions: 
(1) This device may not cause interference, and 
(2) this device must accept any interference, including 
interference that may cause undesired operation of this device.
This transmitter must not be co-located or operated in 
conjunction with any other antenna or transmitter.
This equipment complies with FCC/IC radiation exposure limits 
set forth for an uncontrolled environment and meets the FCC 
radio frequency (RF) Exposure Guidelines in Supplement C to 
OET65 and RSS-102 of the IC radio frequency (RF) Exposure 
rules. This equipment has very low levels of RF energy that is 
deemed to comply without maximum permissive exposure 
evaluation (MPE). But it is desirable that it should be installed 
and operated keeping the radiator at least 20 cm (7
7/8q) or more 
away from person’s body (excluding extremities: hands, wrists, 
feet and ankles).
THE FOLLOWING APPLIES ONLY IN 
CANADA.
This device complies with RSS-210 of the IC Rules. 
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
(2) This device must accept any interference received, 
including interference that may cause undesired operation 
of the device.
Product Identification Marking is located on the bottom of 
the unit.
SC-HC57~RQT9708.book  3 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							4
RQT9708
Table of contents
IMPORTANT SAFETY INSTRUCTIONS ........... 2
Accessories....................................................... 3
Playable media .................................................. 4
Control reference guide ................................... 5
Attaching the unit to a wall (optional) ............. 6
Connections ...................................................... 8
Inserting or removing media ........................... 8
AirPlay ............................................................... 9
Playback operations ........................................11
Listening to the radio ..................................... 12
Internet Radio.................................................. 13
Sound adjustment .......................................... 13
Clock and Timer .............................................. 13
Others .............................................................. 14
Troubleshooting.............................................. 16
Specifications ................................................. 18
Unit and media care........................................ 19
Licenses .......................................................... 19
Spanish Quick Reference / Referencia 
rápida en español
Conexiones ..................................................... 20
Insertar o sacar los medios ........................... 20
Las operaciones de reproducción de CD, iPod/
iPhone .............................................................. 20
Radio ................................................................ 21
Reloj y temporizador ...................................... 21
Limited Warranty (ONLY FOR U.S.A. AND 
PUERTO RICO)................................................ 22
Limited Warranty (ONLY FOR CANADA) ...... 23
Playable media
(as of December 2011)
	≥Compatibility depends on the software version. Update your 
iPod/iPhone to the latest software before using it with this 
unit.
≥Depending on the model, it may be necessary to remove the 
iPod/iPhone and select the album, artist, etc. on the iPod/
iPhone.
≥Be sure to use a dock adapter that is compatible with your 
iPod/iPhone. To purchase a dock adapter, consult your iPod/
iPhone dealer. If a dock adapter is not available, insert and 
remove the iPod/iPhone with care.
≥Please be aware that Panasonic accepts no responsibility for 
the loss of data and/or information.
Charging the iPod/iPhoneThe iPod/iPhone will start being charged once connected 
to this unit.
≥In standby mode, “IPOD CHARGING” is shown on the main 
unit’s display.
≥Check the iPod/iPhone to see if the battery is fully charged. 
(Once fully recharged, additional recharging will not occur.)
≥A disc with the CD Logo.
≥This unit can play back discs that conform to the CD-DA 
format.
≥The unit may not be able to play some discs due to the 
condition of the recording.
≥This unit cannot play back MP3 files.
Note about using a DualDisc≥The digital audio content side of a DualDisc does not meet 
the technical specifications of the Compact Disc Digital Audio 
(CD-DA) format so play may not be possible.
≥Do not use a DualDisc in this unit as it may not be possible to 
insert it correctly and it may get scratched or scraped.
Operations in these instructions are described 
using the remote control, but you can do the 
operations with the main unit if the operations 
are the same.
Compatible iPod/iPhone for 
docking
iPod touch1st, 2nd, 3rd, and 4th generation
iPod nano2nd, 3rd, 4th, 5th, and 6th generation
iPod classic
iPhone 4S / iPhone 4 / iPhone 3GS / iPhone 3G 
/ iPhone
Compatible CD
SC-HC57~RQT9708.book  4 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							5
RQT9708
ENGLISH
Control reference guide
Remote control
1 Turn this unit on or off
2 Select the audio source
3 Basic playback control buttons
4 Enter setup menu
5 Enter the iPod/iPhone menu / 
Change displayed information
6 Open/close the sliding door
7 Adjust the volume8 Mute the soundMutes the sound. Press again to 
cancel. “MUTE” is also canceled 
when the volume is adjusted or the 
unit is turned off.
9 Enter playback menu
10 Enter sound menu
11 Selection/OK 
∫Preparation
Remove the insulation sheet A before using.
∫To replace a button-type battery
1 While pressing the stopper B, 
pull out the battery holder.2 Set the button-type battery 
with its (i) mark facing 
upward and then put the 
battery holder back in place.
Keep the button-type battery out 
of reach of children to prevent 
swallowing.
Battery type: CR2025 (Lithium battery)≥The battery should normally last about 1 year, however this depends on how 
frequently the unit is used.
Main unit
1 Standby/on switch [Í/I]Press to switch the unit from on to standby mode or vice 
versa.
In standby mode, the unit is still consuming a small 
amount of power.
2 Open/close the sliding door (for iPod/iPhone)
3 Select the audio source
4 Basic playback control buttons
5 Adjust the volume (0(min) to 50(max))
6 Open/close the sliding door (for discs)
7 WPS pairing button (>9)
8 Headphone jack
Plug type: ‰3.5 mm (1/8q) stereo
Recommended plug type: Straight Plug
≥To prevent hearing damage, avoid listening for 
prolonged periods of time.
Excessive sound pressure from earphones and 
headphones can cause hearing loss.
9 Standby indicator
10 Wi-Fi® status indicator
11 D i s p l a y
12 Sliding door
13 Remote control signal sensor
Distance:
Within approx. 7 m (23 ft) directly in front.
≥To avoid interference, please do not put any objects in 
front of signal sensor.

8
Top view
SC-HC57~RQT9708.book  5 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							6
RQT9708
Attaching the unit to a wall 
(optional)
∫Supplied accessories
≥1 Safety holder
≥1 Screw
≥2 Wall mount brackets
∫Commercially available accessories 
(not supplied)
≥4 Wall mount bracket fixing screws
≥1 Safety holder fixing screw
≥1 Fall prevention cord
≥1 Screw eye
	Use screws with a nominal diameter of ‰4 mm (5/32q), which are 
suitable to the material of the wall (e.g., wood, steel, concrete, 
etc.)
1Detach the stand from the unit.
{.Unscrew the fixing screw (2 pieces) at the bottom of the 
unit.
{.Gently pull the stand off the unit as illustrated.
≥Keep the removed screws and stand in a safe place.
2Measure and mark the position of the wall 
mount brackets (Both sides).
{.Use figures below to identify the screwing positions.
The position to attach the wall mount brackets
Space required
Installation accessories
≥Keep the safety holder out of reach of children to 
prevent swallowing.
≥Keep the screws out of reach of children to prevent 
swallowing.
≥Keep the wall mount brackets out of reach of children 
to prevent swallowing.
Safety precautions
Professional installation is required.
The installation should never be done by any 
other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY 
DAMAGE AND/OR SERIOUS INJURY, 
INCLUDING DEATH RESULTING FROM 
IMPROPER INSTALLATION OR INCORRECT 
HANDLING.
≥Be sure to install this unit as indicated 
within this Owner’s Manual.
Wall mount instructions
Before installation, turn the unit off and disconnect the 
AC power supply cord from the AC outlet.
Before deciding the location to place the unit, be sure 
to check that the Wi-Fi signal strength is sufficient. 
(>9, 15)
Bottom of main unit
Stand
Soft blanket or clothFixing screw
232 mm (91/8q) 12.5 mm (
1/2q)
300 mm (1113/16q)
247 mm (9
23/32q)
680 mm (30
23/32q) 65 mm
(2
9/18q)
232 mm (9
1/8q)11 6 m m ( 4
9/16q)
11 8 m m
(4
21/32q)
480 mm (19q)11 3 m m
(4
13/32q) 15 mm
(19/32q)
SC-HC57~RQT9708.book  6 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							7
RQT9708
ENGLISH
3Attach the wall mount bracket to the wall with 2 
screws (not supplied). (Both sides)
≥Use a spirit level to ensure both wall mount brackets are 
level.
≥Make sure that the screw used and the wall are strong 
enough to support the weight of at least 33 kg (72.8 lbs).
4Fix the safety holder onto the unit with the 
screw (supplied).
{.Screw tightening torque: 50 N0cm (0.4 lbf0ft) to 70 
N0cm (0.5 lbf0ft).
5Attach the fall prevention cord (not supplied) to 
this unit.
≥Use a cord that is capable of supporting over 33 kg 
(72.8 lbs) (with a diameter of about 1.5 mm (1/16q)).
6Hook the unit securely onto the wall mount 
brackets with both hands.
≥Connect the FM antenna and the AC power supply cord 
to the unit before hanging the unit onto the wall. (>8)
≥After hanging the unit, release your hand carefully to 
confirm the unit sits securely on the wall.
7Drive the safety holder fixing screw 
(not supplied) to secure the safety holder onto 
the wall.
≥Make sure that the screw used and the wall are strong 
enough to support the weight of at least 33 kg (72.8 lbs).
≥Refer to step 3 for requirements before screwing.
8Attach the fall prevention cord (not supplied) to 
the wall.
≥Make sure that the screw used and the wall are strong 
enough to support the weight of at least 33 kg (72.8 lbs).
≥Make sure that the slack of the cord is minimal.
At least 30 mm (13/16q)
‰7.5 mm (
19/64q) to 
‰9.4 mm (3/8q)
4mm 
(
5/32q)
Wall mount bracket
Screw
(supplied)
Cord (not supplied)
Wall
Safety holder fixing screw 
(not supplied)Safety holder
Fixed to the wall
Cord (not supplied) Screw eye (not supplied)
Wall
SC-HC57~RQT9708.book  7 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							8
RQT9708
Connections
	≥These speakers do not have magnetic shielding. Do not 
place them near a television, personal computer or other 
devices easily influenced by magnetism.≥Tape the antenna to a wall or column in a position with the 
least amount of interference. (Use an FM outdoor antenna if 
radio reception is poor.)
Inser ting or removing media
	*1: Make sure to tilt the disc so as not to touch the sliding door.
*2: Do not push or pull the dock manually.
*3: When inserting or removing the iPod/iPhone, tilt the dock 
slightly by holding the corner of the dock.
≥Make sure that the unit does not fall when inserting or 
removing media.
≥Be sure to remove the iPod/iPhone from its case.≥When moving this unit, be sure to remove all media and turn 
this unit to standby mode.
0ç0î0Á0â0ï0õ
0Ø0Ö„
0
						

							9
RQT9708
ENGLISH
AirPlay
With this feature you can wirelessly stream music 
to this unit’s speakers.
∫Compatible devices(as of December 2011)
AirPlay works with;
≥iOS 4.2 or later (iPod touch (2nd, 3rd, and 4th 
generation), iPhone 4S, iPhone 4, iPhone 3GS, 
iPad 2, iPad)
≥iTunes 10.2 or later (Mac / PC)
To use the AirPlay function, this unit must join the 
same wireless network as the compatible device.
Preparation
With this unit there are 2 methods to setup the 
wireless connection. Determine which type of 
wireless network router you are using and follow 
the method that matches your device.
≥Refer to the operating instructions of the wireless 
network router for details.
≥Turn the unit on.
	≥When performing the network settings, place this unit close 
to the wireless router.
≥Simultaneous use with other 2.4 GHz devices, such as 
microwaves, cordless telephones, etc., may result in 
connection interruptions.
≥Immediately after this unit is turned on, the network setup 
may take longer to start.
≥This unit cannot join a wireless network using WEP security 
settings with “Method 1”. Use “Method 2” to join the wireless 
network.
≥To cancel this setting in the middle, press [Í] to turn off the 
unit.
≥For up to date compatibility information on your Wireless 
router refer to 
http://panasonic.jp/support/global/cs/
(This site is in English only.)
∫Using the WPS Push Button Configuration 
(PBC)
1Press and hold [– WPS] on the unit.{.“CONNECT” flashes on the display. (Wi-Fi status 
indicator blinks blue.)
≥Complete step 2 within 2 mins.
2Press the WPS button on the wireless router.{.When a link is established “LINKING” is indicated on 
this unit’s display.
{.When the configuration is finished “SUCCESS” is 
indicated on this unit’s display. (Wi-Fi status indicator 
lights blue.)
3Press [OK] on the remote control to complete 
the setting.
	≥This unit can also be set using the WPS PIN code.
Replace step 2 of “Method 1” with the following steps.
(Before starting, refer to the wireless network router’s 
operating instructions for details on how to enter the PIN 
code.)
1 While “CONNECT” is flashing press and hold [– WPS] 
again to display the 8 digit PIN code. (Wi-Fi status 
indicator blinks purple.)
2 Enter the PIN code into the wireless router.
≥To edit this system’s name it is necessary to use “Method 2”.
≥“FAIL” may be displayed if the connection was not made 
within the set time limit. Try the setting again. If “FAIL” is still 
displayed, try “Method 2”.
With this method, you will access this unit’s 
wireless network settings from the Internet browser 
of your compatible device.
≥The illustrations and explanations are based on an iPhone. 
However, the word “iPhone” can be replaced with your 
compatible device.
Preparation
≥Check your home wireless network name 
(Network name (SSID)) and password for this 
network. This can often be found on the wireless 
router itself.
≥Turn on your iPhone.
(Continues to next page)
*1: WPS stands for “Wi-Fi Protected SetupTM”.
Network settings
If you do not know which type of wireless network 
router you are using, use “Method 2”.
Method 1
If your wireless network router supports WPS*1.
WPS Push Button Configuration 
(PBC) compatible wireless router 
may have this mark.
Method 2
If your wireless network router does not support 
WPS*1.
SC-HC57~RQT9708.book  9 ページ  ２０１２年３月２日　金曜日　午後２時４分 
						

							10
RQT9708
1Press [SETUP] on the remote control 
repeatedly to select “NET SETUP” and then 
press [OK].
{.“SETTING” is indicated on the display. (Wi-Fi status 
indicator blinks purple.)
2Connect your iPhone to this unit’s wireless 
network called “Setup _ _ _ _ _ _”*1, 2.
≥Once “Setup _ _ _ _ _ _” is selected, the iPhone is 
connected with this unit.
3Start Safari on your iPhone and type 
“http://192.168.1.12/” into the URL address 
field and display the page.
{.This unit’s setup window is displayed.
4Select “Search wireless network”.
5Select and input the details.
6Perform the “Additional settings”. (>right)
If they do not apply, continue to the next step.
7Select “JOIN” to apply the settings.
{.In the pop-up screen select “OK” to continue.
– Select “CANCEL” to return to the setup window.
{.The wireless status indicator lights blue.
– You can now close the Safari browser.
{.When the configuration is finished “SUCCESS” is 
indicated on this unit’s display.
8Press [OK] on the remote control to complete 
the settings.
9Connect your iPhone back to your home 
wireless network.
	≥Enable Java and Cookies in your browser settings.
≥To cancel this setting in the middle, press [Í] to turn off the 
unit.
*1: “ _ ” stands for a digit that is unique to each set.
*2: Make sure that DHCP is enabled for the network setting on 
the iPhone.
*3: If you have set your wireless network to be invisible, select 
“BACK” and refer to “Alternative settings”. (>above)
[1]Select your home wireless network 
name.*3
[2]Type the password.
[3]Select “NEXT”.
3
If “FAIL” is displayed press [OK]. Then check the 
wireless network password and other settings 
and start again from step 1.
Alternative settings
Instead of steps 4 and 5:
Select “Manual settings”.
1 Type your home wireless network name 
into the “Network name (SSID)” field.
2 Select the encryption method from the 
“Security system” drop down list.
3 Type the password into the “Password” field 
and then select “NEXT”.
Additional settings
In step 6:If your home wireless network has been setup 
to use specific IP Addresses, Subnet Mask, 
Default Gateway, Primary DNS, etc.
Select “Advanced network settings”.
{.Input the required addresses into each field and select 
“OK”.
≥To change the settings back to DHCP, select “ON” from 
the “DHCP” drop down list.
If you want to change the name of this unit that 
is displayed as the AirPlay speakers.
Select “Edit STEREO SYSTEM name”.
{.Only ASCII characters can be used.
{.Type a new name into the “STEREO SYSTEM name” 
field and select “OK”.
SC-HC57~RQT9708.book  10 ページ  ２０１２年３月２日　金曜日　午後２時４分