Panasonic Color Cctv Cameras Wv Cw484 Operating Instructions

31
Setting Procedures
First, select a language for menu display and camera ID display.
Language Setup (LANGUAGE
SETUP)
1. Select LANGUAGE on the top menu and
press the [SET] button.
→The LANGUAGE SETUP menu opens.
2. Select a language. The default setting is
English.
Available languages: ENGLISH, FRANÇAIS,
DEUTSCH, ESPAÑOL, ITALIANO, êìëëäàâ, JAPANESE, CHINESE
3. Select SET on the menu and press the [SET] button.
1. Camera Identification Setting (CAMERA ID) 
Assign a name to the camera using up to 16...

32
• To erase all characters of the camera ID, select RESET and press the [SET] button.
Note:For Chinese language, up to 8 characters can be entered.
4. To specify the ID display position:
1. Select POSI and press the [SET] button.
→The entered camera ID will be highlighted on the screen.
2. Move it into the appropriate position and press the [SET] button.
→The position is determined and the screen will return to the CAMERA ID menu.
Note:Keep pressing any of [LEFT], [RIGHT], [UP], or [DOWN] button for a...

33
2-2. ALC Mode with SUPER-D3 OFF
1. Move the cursor to ALC on the CAMERA
SETUP menu and select OFF for SUPER-D3
on the ALC CONT menu.
→MASK SET↓appears on the ALC CONT
menu.
2. Select MASK SET and press the [SET] but-
ton. 
→The 48 mask areas appear overlaid on the
camera picture with the blinking cursor in
the upper left corner.
3. Move the cursor to an area where the back-
light is bright and press the [SET] button to
mask the area. 
→The masked area appears alternately
white and blinking when the...

34
Notes:
•Only OFF is available when SUPER-D3 is set to ON.
•When a faster speed is selected for the electronic shutter, the picture will generally become
darker, and sometimes a smear (vertical stripes caused by bright objects) may appear.
4. Gain Control Setting (AGC)
Select an automatic gain control mode. This setting raises the gain and brightens the image
under low light conditions. The default setting is ON (HIGH).
Available modes:ON (HIGH / high), ON (MID / medium), ON (LOW / low), OFF 
5....

35
6. Synchronization Setting (SYNC)
1. Select a sync mode.
VD2:Multiplexed vertical drive, highest priority
LL:Line-Lock, follows the phase of supplied AC power, 2nd priority
INT:Internal sync, lowest priority
Notes: 
•Selection is not available when VD2 is added to the camera. Selection from LL is avail-
able when the respective sync is added.
•When LL is selected, phase adjustment is required.
2. Line-Lock Vertical Phase Adjustment (V PHASE)
•Select LL and press the [SET] button.
•Prepare a dual-trace...

36
AWC Setting
1. Select AWC and press the [LEFT] button. 
→AWC will change to AWC →PUSH SW.
2. Press the [SET] button.
→PUSH SW will be highlighted while the AWC setting is performed.
Note: If the white balance is not set, PUSH SW is being highlighted.
3 . Press the [RIGHT] button.
Manual Fine Adjustment
Perform fine adjustment as necessary. 
1. Select WHITE BAL and press the [SET] but-
ton.
→Fine adjustment menu of ATW or AWC will
open.
2. Adjust finely R (Red) and B (Blue) gain by
moving the I cursor....

37
5. Select ON or OFF for ALARM under DISPLAY MODE.
ON:Outputs an alarm
OFF:Does not output an alarm. This is applicable any of the following controllers are used:
WV-RM70, WV-CU550 series, WV-CU161, WV-CU360, WV-CU650, WV-CU850, WV-
CU950
6. Select DISPLAY MODE and press the [SET] button to see the current settings.
When a motion is detected, the area will blink.
•Press the [SET] button to return to the MODE1 menu.
7. As necessary, repeat to perform LEVEL adjustment and MASK setting by checking on the...

38
About MODE2 of Motion Detection
•The camera will detect a scene change in the following cases.
When the lens is fully sprayed or covered with a cloth, lid, or the like
When the camera direction is suddenly changed
•The camera will not detect a scene change in the following cases.
When a cloth with patterns covers the lens and it sways in the wind
When some portions in the screen are not veiled
When the screens are similar in scene patterns although the camera direction has
changed
•The camera will...

39
→When AUTO1 or AUTO2 is selected, LEVEL and DURATION TIME appear.
3. Select a threshold LEVEL to switch between
the color and black-and-white mode. The
default setting is HIGH.
HIGH:Switches the mode at approx. 5 lx illu-
mination.
LOW:Switches the mode at approx. 1 lx illu-
mination.
4. Select a duration time to determine whether
to switch the mode. The default setting is 30 seconds.
Available time:(Short) 10 s ↔30 s ↔60 s ↔300 s (Long)
5. Select a burst signal mode. The default setting is ON....

40
5. Select →PUSH SW for SCALE and press the [SET] button.
→Zone scale adjustment becomes available.
6. Adjust the zone scale using the [LEFT], [RIGHT], [UP], or [DOWN] button.
7. To apply the settings, move the cursor to SET and press the [SET] button.
→The screen returns to the ZONE NUMBER selection menu.
To delete the settings, select DEL and press the [SET] button.
13. Electronic Zoom (EL-ZOOM)
1. Move the cursor to EL-ZOOM.
2. Select ON or OFF by pressing [LEFT] and
[RIGHT] buttons.
The default...