Panasonic Color Cctv Cameras Wv Cw484 Operating Instructions

11
qPower cable (12 V DC or 24 V AC)
Cautions:
Supplies 24 V AC or 12 V DC from an
external power source.
wVideo output cable with BNC connec-
tor
Connects with the video connector.
eEnclosure
rFocus lever
Fixes the focus position after adjusting.
tZoom lever
Fixes the zoom position after adjusting.
yTilting lock screw
Fixes the tilting position after adjusting.
uAzimuth (Angle adjuster)
Shoots in a straight-angle field of view
when aiming at an object in a slanting
direction even if the tilt angle has...

12
Lens Mounting (WV-CW484FK, CW484SK)
1. Before mounting the lens, remove the protection sheet from the camera.
2. Mount the optional lens to the camera by turning the lens clockwise.
3. Insert the connector of lens into the connector of camera, and bind the connectors with the
fixing band. 

13
Installations
• The following installation should be made by qualified service personnel or system
installers.
• Mounting Bracket (WV-Q114) is optional for WV-CW484F, WV-CW484FK. 
Use the screws provided to the Mounting Bracket.
• Mounting Bracket is provided to WV-CW484S, WV-CW484SK.
Use the screws provided to this product.
Important:
• Prepare four fixing screws to be used to mount the provided camera attachment according
to the material of the area where the attachment is to be installed....

Using Mounting Bracket
• Secure the camera mounting bracket to wall or ceiling, and fix the provided camera attach-
ment to the mounting bracket with the screws for to the mounting bracket. (Refer to the fol-
lowing figures.)
Verify the camera attachment and mounting bracket are mounted firmly after screwing
them.
• When routing cables sideway or through the wall/ceiling, the mounting bracket is used.
• When routing cables sideway, open the
sideway cable exit unscrewing the lid by
use of a hexagon...

15

Camera attachment (provided)
TOP
TOPTOPMounting bracket 

16
How to mount the camera
1. Connect the power cable and the BNC plug of the video output cable. (Refer to p. 23
Connections.)
2. Secure the camera with four attachment fix-
ing screws.

3. Fit the protrusion at the rear of camera unit in
the dent of camera attachment.
Protrusion
Rear screw Screw hole of 
camera attachment
4. Hook the rear screws on the screw holes of
camera attachment, and turn the camera unit
clockwise to fix the camera unit and camera
attachment.
Dent
TOP
Dent

3. Fit the protrusion...

17
5. Remove the enclosure from the main
body by loosening the three fixing
screws.
The enclosure is fixed with tamperproof
screws.
Loosen the three fixing screws by using
the provided bit for tamperproof screw.
Note:Perform the same procedure when
replacing with the optional dome
cover WV-CW4C. 4. Hook the rear screws on the screw holes
of camera attachment, and turn the cam-
era unit clockwise to fix the camera unit
and camera attachment.
Protrusion
Rear screw Screw hole of 
camera attachment
6. Remove...

18
7. Secure the camera unit to the bracket with
the camera lock screw.
(The illustration describes an example using
a junction box.)
Camera fixing screw
8. Adjust the camera. (Refer to p. 21.)
9. Attach the enclosure to the camera.
Firmly tighten the three tamper-proof
screws.
(Recommended tightening torque 0.78
N·m {0.58 lbf·ft})
Notes:
• Defocus may be caused by the reinstalled enclosure. When using a system controller,
adjust the back-focus on the setup menu after attaching the enclosure.
• When not...

19
Waterproof Process
• When routing cables sideway using Mounting Bracket or installing the camera under
eaves, apply waterproof process to the cable and relevant portions.
• The cables are not waterproofed. Provide water sealing for the tube ends and the portions
between cable cores as well as connecting portions.
• The use of vinyl tape or other tapes instead of the butyl tape may cause water absorption
from a gap and finally condensation and water leakage.
Waterproof processing of cable connection...

20
Notes:
• Surely attach a pipe fitting to the bracket to avoid exposing the cables. Otherwise, cable
deterioration resulting from cable exposure may cause a short circuit.
• Run the conduit downward or pull the conduit out of the side of the bracket. When pulling
the conduit out of the side of the bracket, run the conduit downward once, and upward.
• For wall installation, face the drain slitdownward and do not block the slit. When rain water
is accumulated in the bracket, the water blocks the...