Panasonic Color Cctv Camera Wv Cw964p Operating Instructions

PAN/TILT SETTINGS
■Using the Pan/Tilt Setup Menu 
Display the pan/tilt setup menu from the setup menu to
configure pan and tilt settings. 
First, display the pan/tilt setup menu. 
1.Display the setup menu (page 25), move the cursor to
PAN/TILT O, and then press the CAM (SET) button.
This will display the pan/tilt setup menu. 
*The following sections numbered qto !4explain
how to use each of the pan/tilt setup menu items. 
(1) Position Number Selection (PRESET)
Positions can be assigned numbers, each of...

●Auto Focus (AF MODE)
1.Move the cursor to AF MODE, and then tilt the joystick
left or right to select an auto-focus function setting.
MANUAL S.M.L :Auto focus does not operate
after moving to a preset position. 
AUTO S.M.L :Auto focus operates after
moving to a preset position. 
●Sequence/Sort DWELL Time 
(DWELL TIME)
This section explains how to set the length of time the
camera stops (time it stops rotating) and tapes the
scene while in the various preset positions for the
sequence and sort operations...

Notes:
•The HOME setting should be selected when you
want to normally leave the camera in the home
position and occasionally perform pan and tilt,
or when you want to activate SEQ. 
•PATR1-4 displays only the set number of patrol
routines (page 35). 
(5) Auto Mode Setting (AUTO MODE) 
Use the auto mode setting to specify the camera
movement mode (OFF, SEQ, SORT, AUTO PAN,
PATROL 1~4, AUTO TRACK). 
After selecting AUTO PAN, you can use the AUTO PAN
setting menu to configure detailed settings. 
1. Move the...

4. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select the start point and end
point dwell time setting.  
Tilting the joystick cycles through the stop time
display in the sequence shown below. (unit: sec)
5. Move the cursor to PAN LIMIT, and then tilt the
joystick left or right to toggle it on and off. 
ON :Limits manual panning to the zone between the
start point and the end point. The TILT range is
from horizontal to straight down. Select OFF for
the ENDLESS setting (step...

(2) Operate the camera to store the movements. 
LEARNING (***S) is displayed in the center of the
screen when the movements are being stored.
(unit: sec)
*(***S) indicates the amount of time that remains
for storing movements. 
(3) The setup menu is displayed and teaching stops. 
Storing movements stops when the remaining time
reaches 0S. 
Notes:
•Selecting LEARN to teach the camera a patrol
routine causes the following parameters to be
stored along with the camera movements. 
(1) Parameters at the...

6.Use the joystick to point the camera at the location to
be masked, and then press the CAM (SET) button. 
This registers the camera position and returns to
the zone setting menu. 
7.Move the cursor to →PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET) button.
This will display the ZOOM/FOCUS setting menu. 
8. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.  
This completes the adjustment procedure and
returns to...

(10) Digital Flip Setting (DIGITAL FLIP) 
Normally, a camera needs to stop when it points
straight down during tilt. With digital flip, however, the
camera is able to tilt from 0° to 180° in a single motion.
This makes it possible to track objects passing directly
under the camera more smoothly. The picture is
flipped vertically and horizontally when the camera is
at an angle of around 135°. 
1. Move the cursor to DIGITAL FLIP, and then tilt the
joystick left or right to toggle it on and off. 
ON :Turns...

4. Input an area title. 
The text input procedure is the same as that for
camera ID input. 
See steps 3 through 5 under “Camera ID Settings”
on page 22 for information about inputting the text
for the area title and specifying its position on the
display. 
5. Repeat steps 1 through 4 for the other area
numbers, if you want. 
(13) Tilt Angle Setting (TILT ANGLE) 
Selecting 5° for the TILT ANGLE setting allows tilting
past horizontal, in the range of -5° to 185°. 
1. Move the cursor to TILT ANGLE, and then...

-39-
ALARM SETTINGS
■Using the Alarm Setup Menu 
Display the alarm setup menu from the setup menu to
configure alarm settings. 
First, display the alarm setup menu. 
1.Display the setup menu (page 25), move the cursor
to ALARM O, and then press the CAM (SET) button. 
This will display the alarm setup menu. 
*The following sections numbered qto eexplain
how to use each of the alarm setup menu items. 
(1) Motion Detector Setting (MOTION DET)
1. Move the cursor to MOTION DET, and then tilt the
joystick left...

6. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select an alarm detect dwell
time setting. 
After alarm detection, the next alarm is not detected
until the specified dwell time elapses. 
Tilting the joystick cycles through the setting
display in the sequence shown below. (unit: sec)
7. Move the cursor to RECOVER TIME, and then tilt
the joystick left or right to select an alarm reset time
setting. 
Tilting the joystick cycles through the setting
display in the sequence shown...