Panasonic Color Cctv Camera Wv Cw964p Operating Instructions

RS485 SETUP
The following procedure is to configure the RS485
setup when using the system controller to control the
camera (pan, tilt, etc.) via the cameras data port. 
1. Display the setup menu (page 25), move the cursor
to COMMUNICATION O, and then press the CAM
(SET) button. 
This will display the RS485 setup menu. 
2. Check the unit number. (page 13)
The UNIT NUMBER item shows the unit number
specified by DIP Switch 1. The factory default unit
number is 1. 
If DIP Switch 1 specifies 1 to 96 as the...

USING THE SETUP MENU 
This manual describe procedures for operating system
controller WV-CU650. 
All setting configuration procedures start from the
setup menu. This section explains how to display the
setup menu and provides details about the menu items
that it contains. 
■Displaying the Setup Menu 
● When using the WV-CU650
(1) Select the camera (this camera), and the
monitor where displays the setup menu. 
(2) Press the MENU button to display LCD MENU CAM 101. 
(3) Press the ENTER button or CAM (SET)...

-23-
■Scene Select Settings
Display the scene select setting menu from the setup
menu to configure scene select settings. First, display
the scene select setting menu. 
1. Display the setup menu (page 22), move the cursor
to SCENE SELECT O, and then press the CAM
(SET) button. 
This will display the scene select setting menu. 
●Scene Select Settings
Use the following procedure to configure scene select
settings. 
1. Move the cursor to SCENE, and then tilt the joystick
left or right to change the scene...

-24- 2. Move the cursor to →PUSH SET to the right of
PAN/TILT, and then press the CAM (SET) button to
display the PAN/TILT setting menu. 
3. Use the joystick to position the camera, and then
press the CAM (SET) button. 
4. Move the cursor to →PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET)
button to display the ZOOM/FOCUS setting menu. 
5. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
Notes:
•
Focusing may be...

-25-
3.
Use the joystick to move the cursor the character you
want to input, and then press the CAM (SET) button. 
The text input procedure is the same as that for
camera ID input. 
See steps 3 through 5 under “Camera ID Settings”
on page 22 for information about inputting the text
for the preset ID and specifying its position on the
display. 
To copy the preset ID of another position number  Move the cursor to COPY, and then press the CAM
(SET) button. This displays the preset ID of the
position number...

CAMERA SETTINGS
■Using the Camera Setup Menu 
Display the camera setup menu from the setup
menu (Advanced Menu) to configure camera
settings (page 25). 
1.Display the setup menu (page 25), move the cursor to
CAMERA O, and then press the CAM (SET) button. 
This will display the camera setup menu. 
*The following sections numbered qto !3explain
how to use each of the camera setup menu items. 
(1) Camera ID (CAMERA ID)
See page 22 for information on the camera ID
settings method. The factory default setting...

-27- (2) Press the CAM (SET) button to mask the cell. 
Moving the cursor to a cell that is already
masked causes the blinking pattern of the
cursor to alternate between horizontal stripes
and white. 
Pressing the CAM (SET) button while the cursor
is located at a masked cell cancels the masking
of the cell. 
To cancel all masking areas, press the F3
button.
(3) After masking all of the cells you want, press the
MON (ESC) button to return to the ALC CONT
menu in step 1.
6. Move the cursor to LEVEL, and...

-28- (6) Synchronization (SYNC)
This camera supports the following three sync modes,
which are listed in priority sequence from highest
priority to lowest. 
(1) Multiplexed vertical drive (VD2) 
(2) Internal sync (INT)
(3) Line-lock (LL)
Input of a multiplexed vertical driver (VD2) signal
automatically switches to VD2 sync, regardless of the
cameras current sync mode (SYNC). In this case, the
camera setting menu shows EXT (VD2) for the SYNC
setting, which cannot be changed to internal sync
(INT) or...

-29- Note:White balance is adjusted in accordance with
on-screen color temperature, which the camera
detects automatically. Correct adjustment may not
be possible if a strong light source is shining on the
screen.
(8) Digital Noise Reduction (DNR) 
1. Move the cursor to DNR, and then tilt the joystick
left or right to select a digital noise reduction (DNR)
setting.  
LOW :Low DNR, Low afterimage. This is the factory
default setting.
HIGH :High DNR, High afterimage
(9) Resolution (RESOLUTION) 
1. Move the...

-30- (11) Auto Focus (AF MODE)
1. Move the cursor to AF MODE, and then tilt the
joystick left or right to select an auto-focus mode
setting.
MANUAL S.M.L :Activates auto-focus when the AF
button on the system controller is
pressed. 
AUTO S.M.L :Auto focus is used automatically
when PAN, TILT or ZOOM are
used in manual operation. 
The letters S (Small), M (Medium), and L (Large)
indicate the size of the auto-focus sensing area.  
The factory default setting is AUTO L.
Notes:
•The AUTO (S.M.L.) setting can...