Panasonic Color Cctv Camera Wv Cw864 Operating Instructions
Have a look at the manual Panasonic Color Cctv Camera Wv Cw864 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
52 Unit Number Switch 1, an 8-bit DIP switch, specifies the unit number or restores the factory default settings when using the Panasonic protocol. When the switch position corresponding to the unit number 1- 96* is selected, setting should be made on the RS485 SET UP menu (see page 47). 1234 ON5678 SW1 8-bit DIP SW For Panasonic’s Protocol 1234 ON5678 Switch positionUnit number 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 Switch positionUnit numberSwitch positionUnit number 1-96* 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 2223 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 4546 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON567 8 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON56 78 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 (to be continued)
53 1234 ON5678 Switch positionUnit number 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 Switch positionUnit numberSwitch positionUnit number 69 70 71 72 73 74 75 76 7778 79 80 81 82 83 84 85 8687 88 89 90 91 92 93 94 951234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678 1234 ON5678
54 (2) Be sure to hook the fall prevention wire into the bracket. (3) Fix the camera to the upper base. •Move the camera up so that its guide pins fit into the guide holes of the upper base. •Turn the camera counter-clockwise to the end, viewed from the bottom. •Fasten 3 screws. Full duplex (4 line) * BP 2 BP 1 Function Switch position Function Switch position RS485 Setting The 4-bit DIP switch is used for RS485 termination. ON OFFTermination ON Termination OFF * 1234 ON SW2 4-bit DIP SW BP 3 BP 4 ON ON ON OFF OFF OFFHalf duplex (2 line) Notes: •Defaults are marked with *. •BP stands for Bit Position. •Full duplex is not available in a daisy chain connection. (Panasonic system controllers only) 5. Mounting the camera (1) Aim the “START” arrow at the bent por- tion of the leaf spring. START Leaf SpringBending Fall Prevention Wire X3 Screws Upper Base Enclosure
55 How to Assemble the Cable with the Accessory Connector Strip back the cable jacket approx. 3 mm (0.1 inch) and separate the individual conductors. Recommended wire gauge sizes for 24 V AC line #24 (0.22mm2) Copper wire size (AWG) Length of cable (approx.)(m) (ft)#22 (0.33mm2)#20 (0.52mm2)#18 (0.83mm2) 20 30 45 75 65 100 160 260 Accessory Connector Information Pin no. Power source 1 2 3 424 V AC LIVE 24 V AC NEUTRAL Ground Not use ContactUp Wire Prepare the individual conductors for clamping. Use MOLEX band tool part number 57027-5000 (for UL-Style Cable UL1015) or 57026-5000 (for UL-Style UL1007) for clamping the contacts. After clamping the contacts, push them into the proper holes in the accessory connector of this camera until they snap in place. •Shrinking the cable-entry seal is a one- time procedure. Do not shrink the cable- entry seal until it has been ascertained that the unit is functioning. •CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. ContactInsert UpAApprox. 3 mm (0.1 inch) Insert the wire until A position and clamp the contacts.Wire UpWire Contact Up Contact Wire Approx. 3 mm (0.1 inch) Insert the wire until A position and clamp the contacts. 1 3 2 4 • 24 V AC Power Supply Connection CAUTIONS Note:When powered up, the unit performs a self-check (including one panning, tilting, zooming and focusing operation). CONNECTIONS • The following connections should be made by qualified service personnel or system installers in accordance with all local codes. • Switch the 24 V AC power source off before installation and connection. Precautions ✻The coaxial cable length (RG-59/U, BELDEN 9259) for the connec- tion is up to 900 meters (3 000 ft.)To VIDEO IN (CAMERA IN) Video output 24 V AC BNC plugCoaxial cableRS485 cable Data port BNC plug Alarm in Alarm outTo sensors To indicators 24 V AC cable for Camera 24 V AC cable for Heater
56 Gray White Pink Yellow green or light blue Black Brown Red Orange Yellow Light blue or green Blue PurpleWire color Wire color •RS485 Connection Note: Use the cable that is described below for RS485 site communication. •Shielded, twisted pair cable •Low impedance •Wire gauge size is thicker than AWG #22 (0.33 mm 2). •ALARM IN Connections An 8-pin and a 4-pin harness are supplied with the camera as standard accessories. Connect exter- nal sensors to this connector. Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low when active). The table below shows wire colors versus pin functions. GND Brown Red Data transmission Data receptionOrange Yellow Green T (B) T (A) R (B) R (A) Note:Use a relay if the voltage or current of the connected device exceeds the ratings. •ALARM OUT Connections Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications are low-active, open-collector and a drive capacity of 16 V DC 100 mA maximum. The table below shows wire colors versus pin functions. Function OUT 1 GND OUT 2 GND Alarm OUT (4-pin) Function IN 1 GND IN 2 GND IN 3 GND IN 4 GND Alarm IN (8-pin)
57 Note:When any peripheral is turned off and turned on again, the camera is also turned off and turned back on. SYSTEM CONNECTIONS 123456789MO NCAM ESC SET0ACK RESETBACK SEQFORWARD SEQ ALTDEC –1CAMINC +1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS NEAR ZOOM TELE FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP DOWN ALARMBUSYF3F4F2F1AF123456789MO NCAM ESC SET0ACK RESETBACK SEQFORWARD SEQ ALTDEC –1CAMINC +1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS NEAR ZOOM TELE FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP DOWN ALARMBUSYF3F4F2F1AF123456789MO NCAM ESC SET0ACK RESETBACK SEQFORWARD SEQ ALTDEC –1CAMINC +1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS NEAR ZOOM TELE FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP DOWN ALARMBUSYF3F4F2F1AF123456789MO NCAM ESC SET0ACK RESETBACK SEQFORWARD SEQ ALTDEC –1CAMINC +1CAM STOP12AUXCLOSE OPENIRISPRESETFOCUS NEAR ZOOM TELE FAR WIDESystem Controller WV-CU550550BLEFT RIGHTUP DOWN ALARMBUSYF3F4F2F1AF Max. 64 cameras VCRs (up to 16) Monitors (up to 16) Printer System controller Color CCTV cameras Matrix switcher Personal computer RS-232C port System status monitor Alarm inputs
58 Zoom ratio Bright object SmearWhen the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. SPECIFICATIONS PREVENTION OF BLOOMING AND SMEAR Power source3.65 mm (H) x 2.74 mm (V), 1/4” 768 (H) x 494 (V) Dimensions Focus speed Effective pixels 15.734 kHz F1.6 to 22, CLOSE Focal length BLC 24 V AC, 60 Hz 200 mm (D) x 360 mm (H) [7-7/8” (D) x 14-3/16” (H)] approx. 5 kg (11 lbs) −30 °C to +50 °C (–22 °F to 122 °F) * See note. Caméra: 18 W, Cauffage: 41W Power consumption Ambient operating temperature Weight selectable ON/OFF (SETUP MENU) x 22 +digital zoom x10 internal/line-lock / multiplexed vertical drive (VD2) 59.94 Hz 1.0 V[p-p] NTSC composite/75 Ω more than 480 lines at center (C/L), 570 lines at center (B/W) more than 350 lines at center 50 dB (AGC OFF, weight on) 0.5 lx (0.05 foot-candle) C/L, 0.03 lx (0.003 foot-candle) B/W at SENS UP x 2 (AGC HIGH) approx. 4.5 s (TELE/WIDE) in manual mode approx. 6.0 s (FAR/NEAR) in manual mode automatic (open/close is possible)/manual 1 : 1.6 (WIDE) - 3.0 (TELE) 3.79 to 83.4 mm 2.6 ° to 51.7 ° 2.0 ° to 39.9 ° 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s Scanning area Synchronization Horizontal scanning fre- quency Vertical scanning fre- quency Video output Horizontal resolution Vertical resolution Signal-to-noise ratio Minimum illumination Zoom speed Iris Maximum aperture ratio Angular field of viewH V Electronic shutter Iris range max 32 times, AUTO/FIX SENS UP ON (LOW)/ON (MID)/ON (HIGH)/OFF AGC WV-CW864 * Note:The picture quality and camera performance are not guaranteed until the inside temperature rises up to –10 °C (14 °F).
59 Controls Panning range Weights and dimensions indicated are approximate. Specifications are subject to change without notice.360° endless possible (in auto-pan mode) manual/sequential position/sort position/auto pan manual : approx. 0.1 °/s to 120 °/s 8-steps/64-steps sequence position : maximum approx. 300 °/s 0° to 180° manual/sequential position/sort position manual : approx. 0.1 °/s to 120 °/s. 8-steps/64-steps sequential position : maximum approx. 300 °/s pan/tilt, lens, 64 preset positions, home position Panning angle setting Panning mode Panning speed Tilting range Tilting mode Tilting speed ACCESSORIES Alarm in cable .................................................................. 1 pc. Alarm out cable ................................................................ 1 pc. Connector for 24 V AC ..................................................... 1 pc.MANUAL/AUTO OFF/SEQ/SORT/AUTO PAN/PATROL SEQ/SORT/AUTO PAN/PATROL PLAY ON/OFF preset ID, camera ID, area title : up to 16 characters ON/OFF 4 inputs (ALARM IN 1 - 4) 2 outputs (ALARM/AUX1, B/W/AUX2) AUTO/ON/OFF ON/OFF, up to 8 zones ON/OFF LEARN/PLAY/STOP, up to 30 seconds ON/OFF Auto mode Auto pan key Digital flip Camera ID Motion DET Alarm IN Alarm OUT B/W mode Privacy zone Proportional PAN/TILT Patrol Cleaning OPTIONAL ACCESSORIES Sun shield ............................................................................................... WV-7176EImage Hold ON/OFF Auto Focus
60 Selecting a PRESET position From #1 to #64 #1 [1] + [CAM FUNC] #10 [1] + [0] + [CAM FUNC] #64 [6] + [4] + [CAM FUNC] AUTO PAN ON [6] + [5] + [CAM FUNC] OFF [6] + [6] + [CAM FUNC] Speed Up [6] + [7] + [CAM FUNC] Speed Down [6] + [8] + [CAM FUNC] Setting Start Point [6] + [9] + [CAM FUNC] Setting End Point [7] + [0] + [CAM FUNC] Setting PAN Reverse [7] + [4] + [CAM FUNC] AUTO MODE MODE Off [7] + [1] + [CAM FUNC] SEQ On [7] + [2] + [CAM FUNC] SORT On [7] + [3] + [CAM FUNC] ENDLESS PAN On [7] + [6] + [CAM FUNC] Off [7] + [7] + [CAM FUNC] DIGITAL FLIP On [7] + [8] + [CAM FUNC] Off [7] + [9] + [CAM FUNC] PROP. PAN/TILT On [8] + [0] + [CAM FUNC] Off [8] + [1] + [CAM FUNC] BLC On [8] + [4] + [CAM FUNC] Off [8] + [5] + [CAM FUNC] AUTO FOCUS STOP AF On* [8] + [6] + [CAM FUNC] STOP AF Off* [8] + [7] + [CAM FUNC] AF On (Activate) [8] + [8] + [CAM FUNC] HOME POSITION Move to HOME [8] + [9] + [CAM FUNC] B/W or C/L B/W On* [9] + [0] + [CAM FUNC] B/W Off* [9] + [1] + [CAM FUNC] B/W AUTO* [9] + [2] + [CAM FUNC] CAMERA ID On [9] + [3] + [CAM FUNC] Off [9] + [4] + [CAM FUNC] AREA TITLE NESW On [9] + [5] + [CAM FUNC] USER On [9] + [6] + [CAM FUNC] TITLE Off [9] + [7] + [CAM FUNC]EL-ZOOM On [9] + [8] + [CAM FUNC] Off [9] + [9] + [CAM FUNC] RESTART Begin [1] + [0] + [0] + [CAM FUNC] Memorize PRESET From #1 to #64** Position #1 [1] + [0] + [1] + [CAM FUNC] Position #10 [1] + [1] + [0] + [CAM FUNC] Position #64 [1] + [6] + [4] + [CAM FUNC] PATROL PLAY [1] + [6] + [5] + [CAM FUNC] STOP [1] + [6] + [6] + [CAM FUNC] LEARN (Start) [1] + [6] + [7] + [CAM FUNC] IRIS Open [1] + [6] + [9] + [CAM FUNC] Close [1] + [7] + [0] + [CAM FUNC] EL-SHUTTER On [1] + [7] + [1] + [CAM FUNC] Off [1] + [7] + [2] + [CAM FUNC] Speed Up [1] + [7] + [3] + [CAM FUNC] Speed Down [1] + [7] + [4] + [CAM FUNC] AGC On [1] + [7] + [5] + [CAM FUNC] Off [1] + [7] + [6] + [CAM FUNC] SENS UP On [1] + [7] + [7] + [CAM FUNC] Off [1] + [7] + [8] + [CAM FUNC] Up [1] + [7] + [9] + [CAM FUNC] Down [1] + [8] + [0] + [CAM FUNC] SENS UP AUTO On [1] + [8] + [1] + [CAM FUNC] Off [1] + [8] + [2] + [CAM FUNC] Up [1] + [8] + [3] + [CAM FUNC] Down [1] + [8] + [4] + [CAM FUNC] LL SYNC phase INC [1] + [8] + [5] + [CAM FUNC] DEC [1] + [8] + [6] + [CAM FUNC] PAN 180 ° turn [1] + [8] + [7] + [CAM FUNC] CLEANING On [1] + [8] + [8] + [CAM FUNC] Off [1] + [8] + [9] + [CAM FUNC] BW SW AUTO 30 sec. [1] + [9] + [0] + [CAM FUNC] 60 sec. [1] + [9] + [1] + [CAM FUNC] 300 sec. [1] + [9] + [2] + [CAM FUNC] 600 sec. [1] + [9] + [3] + [CAM FUNC] Function APPENDIX Shortcuts Shortcut operations are available for controllers having the CAM FUNCTION key. Entering from one to three digits using the numeric key(s) and pressing the CAM FUNCTION key will create a shortcut to the respective functions. The CAM FUNCTION key is abbreviated as [CAM FUNC] in the table below. Key Function Key Notes: •Shortcut operations marked with * will change parameter settings only. Actual operation takes place when the conditions for the changed settings are met. •When entering shortcuts marked with **, “NO REGS. ; FLIP ON” may appear on the monitor. Re-enter the shortcut. •Shortcuts may be ignored while PAN/TILT, ZOOM or FOCUS is in operation. •PATROL LEARN saves only [1] through [6]+[4], [1]+[6]+[9] and [1]+[7]+[0] in the memory. •PATROL PLAY stops when a shortcut other than [1]+[6]+[9] or [1]+[7]+[0] is entered.
N0202-1032 V8QA5996BN Printed in Japan Imprimé au Japon 2002 © Matsushita Communication Industrial Co., Ltd. All rights reserved. Panasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 Panasonic Sales Company Division of Matsushita Electricof Puerto Rico Inc. Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 (809)750-4300 Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840