Panasonic Color CCTV Camera Wv Cw334 Wv Cw364 Operating Instructions

21
 w  Engage the attachment mounting screw of 
the camera with the camera mounting hole 
of  the  camera  attachment  and  rotate  the 
camera  in  the  direction  of  the  arrow  to  the 
"LOCK"  position  to  secure  the  camera  to 
the  camera  attachment  without  any  back-
lash. 
  e  Connect  the  power  cord  and  the  video 
output  cable  at  the  side  of  the  mounting 
base. (+ page 28)
    Apply  waterproof  treatment  to  the  con-
nected section. (+ page 26)
  r  Accommodate...

22
 t  Mount  the  supplied  base  cover  on  the 
mounting base. 
Important:
	 •	 To	 prevent	 the	cables	 from	being	 caught	
when the base cover is attached, keep the 
cables inside the cable guide. 
  y  Use  the  bit  for  tamperproof  screw  (acces-
sory)  to  tighten  the  fixing  screws  provided 
on both sides of the base cover. 
    (Recommended tightening torque:  
0.78 N·m {0.58 lbf·ft})
x   Remove the dome cover from the 
main body by loosening the three 
fixing screws. 
    Loosen the three...

23
c   Secure the camera to the bracket 
with the camera fixing screw (red, 1 
position). 
Important:
	 •	 The	 camera	fixing	screw	 shall	be	securely	
tightened.  Otherwise,  water  exposure  may 
cause  damage  or  malfunction  of  camera, 
or  camera  dropping  may  result  in  injury. 
(Recommended tightening torque: 
    0.78 N·m {0.58 lbf·ft})
     

24
Adjust the camera
z
   Pan, tilt and azimuth adjustment 
Important:
	 •	 Do	 not	touch	 the	iris	motor.	 Failure	 to	
observe this may cause trouble.
	 •	 Do	 not	hold	 the	camera	 by	the	 lens	 unit	
when adjusting panning, tilting, or azimuth.
Detach  the  inner  dome  from  the  camera  by 
picking the front and rear sides.
Note:
	 •	 Do	not	touch	the	lens.
 
At  the  same  time  as  the  pan  and  tilt  adjust-
ments,  make  the  zoom  and  focus  adjustments 
in Step 2.  
q  Rotate the panning...

25
Note:
	 •	 When	 the	zoom	 lock	knob  is  adjusted  to 
the  WIDE  side  and  the  tilt  angle  is  approx. 
±75  °,  1/3  part  of  the  screen  may  be  hid-
den.
Important
	 •	 Tighten	 the	panning	 table	lock	screw	 and	
tilting  lock  screw.  (Recommended  tighten-
ing torque: 0.59 N·m {0.44 lbf·ft})
  e  Rotate  the  azimuth  adjuster  to  adjust  the 
azimuth  angle  of  the  image  (Range: 
±100°).
x   Zoom and focus adjustment
At  the  same  time  as  adjusting  the  pan  and 
tilt(Step 2),...

26
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when the camera with exposed cables is 
installed  by  means  of  the  mounting  base  or  it  is  installed  under  the  eaves.  The  camera  body  is 
waterproof, but the cable ends are not waterproof. 
Be sure to use the supplied butyl tape at the connection parts of the power cord and video output 
cable  to  apply  waterproof  treatment  in  the  following  procedure.  Failure  to  observe...

27
Important:
	 •	 If	 open	wiring	 is	conducted,	 be	sure	 to	use	 conduits	 and	run	the	cables	 inside	the	tubes	 to	pro-
tect the cables from direct sunlight. 
	 •	 When	 the	conduit	 is	connected	 at	the	 lateral	 or	bottom	 position,	 either	of	the	 arrow	 marks	 on	
the bracket shall be the top position.
	 •	 When	 the	conduit	 is	connected	 from	the	top,	 the	arrow	 mark	on	the	 attachment	 shall	be	either	
of the right or left position. 
    
    
	 •	 For	 installation	 on	the	 wall,	 do	not...

28
Make a connection
Cautions:
	 •	FOR  UL  LISTED  MODEL(S),  ONLY  CONNECT  THIS  TO 24  V  AC  OR  12  V  DC  CLASS  2 
POWER SUPPLY.
	 •	 Be	sure	to	connect	the	grounding	lead	to	the	GND	terminal.
* When using 12 V DC power suppl y,
the optional heater unit is unavailable. T
o 24  VAC/12 V DC* 
power supply
V ideo output cable  Brown (Live)
Blue (Neutral)
Green/
Yello w (GND)
To GND (only for 24 V AC)
BNC connector BNC connector
BNC connectorTo VIDEO IN
Power cord  
l Video output connection
The...

29
• Cord length and wire gauge
24 V AC
The  recommended  cord  length  and  copper 
wire size are shown in the table for reference. 
The  voltage  supplied  to  the  camera  should  be 
between 19.5 V AC and 28 V AC. 
Recommended wire gauge for 24 V AC line. 
Copper wire size 
(AWG)#24 
(0.22 mm2) #22 
(0.33 mm2) #20 
(0.52 mm2) #18 
(0.83 mm2)
Length of 
cable 
(approx.) m
20 304575
feet 66 100 150250
12 V DC
The  recommended  resisance  and  copper  wire 
size are shown in the table for reference....

30
Optional Heater Unit WV-CW5H (option)
Installing  the  heater  unit  enables  the  camera  to  operate  in  a  low-temperature  environment  below 
–30 °C {–22 °F}. The heater turns on automatically when the temperature inside the camera drops 
below +10 °C {50 °F} and turns off when the temperature rises. A small fan inside the unit will mini-
mize  condensation  on  the  surface  of  the dome  cover  caused  by  changes  in  ambient  temperature 
unless temperatures change too rapidly.  
Important:...