Panasonic Color CCTV Camera Wv Cw334 Wv Cw364 Operating Instructions

11
Screw tightening
	 •	 The	screws	and	bolts	 must	 be	tightened	
with  an  appropriate  tightening  torque 
according  to  the  material  and  strength  of 
the installation area.
	 •	 Do	 not	use	 an	impact	 driver.	Failure	 to	
observe this may cause overtightening and 
consequently damage to the screws.  
	 •	 When	 a	screw	 is	tightened,	 make	the	
screw  at  a  right  angle  to  the  surface.  After 
tightening  the  screws  or  bolts,  perform 
visual check to ensure tightening is enough 
and...

12
Major operating controls and their functions
12
3 4
q Power cord
* This illustration shows the camera  without the inner dome.
w Video output cable
e Dome cover
t Panning table
!0 Focus lock knobo  Zoom lock knob y
Tilting table
u Tilting lock screw (left and right) 
!5
 Inner dome
!1 Camera xing screw
!2 Heater output connector
!3
 Dip switch
i Azimuth adjuster
!4Monitor output connector 
(RCA)
r Panning lock screw [LOCK] 

13
 q  Power cord
    Supplies  24  V  AC  or  12  V  DC  from  an 
external power source.
 w  Video output cable
    Transmits  composite  video  signals.  If  this 
unit  is  connected  to  the  multiplex  unit,  the 
multiplexed VD2 that is prioritized over INT 
is automatically selected.
  e  Dome cover
  r  Panning lock screw [LOCK]
    Fixes the panning table.
  t  Panning table
    Rotate  this  table  to  adjust  the  panning 
angle of the camera.
  y  Tilting table
    Adjusts the tilting...

14
   Adaptive black stretch selector [B.S.]:
ON (default): Corrects the dark area of an 
object automatically to lighten it.
OFF: Does not compensate.
Note:
	 •	 When	 set	to	"ON",	 noise	may	be	increased	
in the dark area of the object.
    In  addition,  darkness  and  brightness  may 
be emphasized in the vicinity of the bound-
ary between the dark and bright areas.
      Backlight compensation selector 
[BLC]:
ON:  Compensates  the  background  auto-
matically if it is brighter than the...

15
Preparations
When  installing  the  camera  on  a  wall  or  a  ceiling,  there  are  two  methods  as  specified  below.  
(+ Next page)
	 •	 Using	a	two-gang	junction	box
	 •	 Using	the	mounting	base
Refer  to  all  work  related  to  the  installation  of  this  product  to  qualified  service  personnel  or  system 
installer. 
	 •	 The	mounting	base	is	supplied.	Use	the	screws	supplied	with	this	product.	
Important:
	 •	 Prepare	 the	mounting	 screw	according	 to	the	 material	 of	the	 area...

16
Using a two-gang junction box
	 •	 When	the	camera	 is	installed	 using	the	two-gang	 junction	box,	mount	 the	camera	 attachment	
(accessory) to the embedded box installed on the wall or ceiling as a \
first step.  
Note:
  •  For wall mounting: 
    Installation  shall  be  performed  in  such  a  manner  that  "MTOP"  of  the  camera  attachment  faces 
upward. 
  •  For ceiling mounting: 
    The front side (model number indication face) of the camera shall be aligned in the direction of...

17
z Install the mounting base on the wall/ceiling.
Note:
	 •	 Only	 the	same	 type	of	holes,	 A  or B,  shall  be 
used for mounting. 
    
B B
B
A
A
A
51 mm {2 inches}
ø27 mm {1-1/16 inches}
Cable access hole
Center of mounting base
Female thread for conduit
(For use of the hole A) (For use of the hole B)
138 mm
{5-7/16 inches} 138 mm
{5-7/16 inshes}85 mm
{3-11/32 inches}
85 mm
{3-11/32 inches}
(A For use of the hole)
Mounting base
B
B B
B A
A
A
A 

18
x   Previously run the cables from the wall or ceiling through the cable access hole. 
c   Mount the attachment onto the mount bracket. 
    Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Camera attachment
FRONTTOP
Note:
  •  For wall mounting: 
    Installation  shall  be  performed  in  such  a  manner  that  "MTOP"  of  the  camera  attachment  faces 
upward. (Except for the case of connecting the conduit from the top. (+ page 27))
  •  For ceiling mounting: 
    The front side...

19
Camera installation
z Mount the camera. 

 q  Connect the power cord and the video output cable. (+ page 28)
  w  Align the "OPEN" mark of the camera with the protrusion of the camera attachment. 
  e  Engage  the  attachment  mounting  screw  of  the  camera  with  the  camera  mounting  hole  of  the 
camera attachment and rotate the camera in the direction of the arrow to the "LOCK" position 
to secure the camera to the camera attachment without any backlash. 
FRONTTOP
OPEN
LOCK...

20

 q  Attach the camera onto the camera attachment 
while  aligning  the  "OPEN"  mark  of  the  camera 
with the projection of the camera attachment.
Important:
	 •	 When	 mounting	the	camera	 body,	cables	 shall	
be  run  between  the  camera  attachment  and 
mounting base as indicated by the arrow in the 
illustration. 
  * Cable  running  as  indicated  by  the  arrow  is  an 
example.  Cable  running  shall  be  varied  with 
installation environment. 
    
LOCKOPEN
LOCKOPEN
Projection