Panasonic Color CCTV Camera WV CS584 WV CW594 Wv Cs580 Wv Cs590 Series Operating Instructions

11
Note: 
•		The 	following 	are 	the 	differences 	between 	AUTO	
and	FIX.	
     AUTO  :		Selecting	 X32	AUTO,	 for	example, 	
automatically  increases  sensitivity,  up  to 
a	maximum	of	32	times.	
     FIX  :		Selecting	 X32	FIX,	 for	example, 	
increases sensitivity 32 times. 
•		 Turning	on	SENS	UP	can	cause	digital	noise
			and	white	spots	(blemish)	to	appear	in	the	picture.
6  White Balance (WHITE BAL)
  1.  Move  the  cursor  to  WHITE  BAL,  and  then  tilt  the 
joystick  left  or  right  to...

12
Note:
•			 With some monitors and VTR models, output of a 
camera images in the black and white mode will 
not display a proper image unless a burst signal is 
provided.	Select	ON	for	this	setting	when	using	
equipment that requires a burst signal.
 
9   Auto Focus (AF MODE)
	1.	 Move 	the 	cursor 	to 	AF 	MODE, 	and 	then 	tilt 	the	
joystick  left  or  right  to  select  an  auto-focus  mode 
setting.
   MANUAL S.M.L:    Auto  focus  does  not  operate  after 
moving  to  a  preset  position,  when...

13
Notes:
•			If	zoom	limit	is	set	to	more	than	36x,	then	zoom	
operation	pauses	at	36x	magnification.
•		 Increasing	the	zoom	to	over	36x	magnification	
(digital	zoom)	decreases	the	resolution.
•		 You	cannot	set	a	zoom	magnification	of	greater	
than	36x	as	a	preset	position.
 
A   Auto Image Stabilizer (STABILIZER)
T h i s   f u n c t i o n   e l e c t ro n i c a l l y   c o m p e n s a t e s   f o r   a n 
u n s t a b l e   c a m e r a   i m a g e   d u e   t o   m o v e m e n t   o f   a 
mounting...

14
Pan/tilt settings
n Using the Pan/Tilt Setup Menu 
Display the pan/tilt setup menu from the setup menu to 
configure pan and tilt settings. 
First,	display	the	pan/tilt	setup	menu.	
	1.	 Display	the	advanced	 setup	menu	(page	 8),	move	
the	 cursor	 to	PAN/TILT	
,  and  then  press  the  CAM 
(SET)	button.	
   This will display the pan/tilt setup menu. 
  *	 The	 following	 sections	numbered	 1  to  D	explain	
how to use each of the pan/tilt setup menu items. 
 
1  Position Number Selection (PRESET)...

15
	2.	 Press	the	CAM	(SET)	button.	
   This will display the scene file setting menu.
    The  following  items  can  be  set  on  the  Scene  file 
settings  menu.  See  camera  settings  for  details  on 
each setting. 
	 •	 SHUTTER	(page	10)
	 •	 AGC	(page	10)
	 •	 SENS	UP	(page	10)	
	 •	 WHITE	BAL	(page	11)
	 •	 VMD	(page	22)	
l    Preset Speed Setting (PRESET SPEED)
Set  the  speed  the  camera  moves  to  the  various  preset 
positions	 for	the	 sequence	 and	sort	operations	 (page	
16).	
  1....

16
Notes: 
•			 The 	HOME 	setting 	should 	be 	selected 	when 	you	
want  to  normally  leave  the  camera  in  the  home 
position  and  occasionally  perform  pan  and  tilt,  or 
when you want to activate SEQ. 
•		 	PTR1-4 	displays 	only 	the 	set 	number 	of 	patrol	
routines	(page	17).	
 
5  Auto Mode Setting (AUTO MODE) 
Use  the  auto  mode  setting  to  specify  the  camera 
movement	 mode	(OFF,	SEQ,	SORT,	 AUTOPAN, 	
PATROL	1~4,	AUTOTRACK).	
After	 selecting	 AUTOPAN,	 you	can	 use	the	AUTOPAN...

17
 4.  Move  the  cursor  to  DWELL  TIME,  and  then  tilt  the 
joystick left or right to select the start point and end 
point dwell time setting.  
    Tilting  the  joystick  cycles  through  the  stop  time 
display	in	the	sequence	shown	below.	(unit:	sec)
    The factory default setting is 1S.
	5.	 Move 	the 	cursor 	to 	PAN 	LIMIT, 	and 	then 	tilt 	the	
joystick	left	or	right	to	toggle	it	ON	and	OFF.	
   ON  :	Limits	 manual	 panning	 to	the	 zone	 between 	
the  start  point  and  the  end...

18
 Note	 that	the	total	 patrol	 time	is	two	 minutes,	 and	the	
time allowed for each routine depends on the number 
of  patrol  routines  that  are  configured.  The  values  in 
parentheses  indicate  the  time  of  each  patrol  routine 
(two	 minutes	 for	one	 pattern,	 one	minute	 each	for	two	
patterns,	30	seconds	each	for	four	patterns).	
  
If  you  want  to  change  the  number  of  patrol  routines 
f ro m   a   p re v i o u s   s e t t i n g ,   f i r s t   d e l e t e   a l l   o f   t h e...

19
 7.  Use the joystick to point the camera at the location to 
be	masked,	and	then	press	the	CAM	(SET)	button.	
    This  registers  the  camera  position  and  returns  to  
the	zone	setting	menu.	
  8.  Move the cursor to  →PUSH	 SET	to	the	 right	 of	ZOOM/
FOCUS,	and	then	press	the	CAM	(SET)	button.	
	 	 This	will	display	the	ZOOM/FOCUS	setting	menu.	
  9.  Move  the  joystick  left,  right,  up  and  down  to  adjust 
the  position  of  the  lens  focus,  and  then  press  the 
CAM	(SET)	button....

20
The	direction	 indicators	 are	N	(north),	 NE	(northeast),	 E	
(east), 	SE 	(southeast), 	S 	(south), 	SW 	(southwest), 	W 	
(west),	and	NW	(northwest).
  1.  Move  the  cursor  to  AREA  TITLE,  and  then  tilt  the 
joystick  left  or  right  to  turn  the  area  title  display 
function on or off. 
   ON (NESW)  : Displays direction indicators. 
	 	 	 Selecting 	ON 	(NESW) 	and 	pressing 	the	
CAM 	(SET) 	button 	will 	display 	the 	position	
(NESW)	 setting	menu,	which	you	can	 use	for...