Panasonic Color Cctv Camera Wv Cs574 Operating Instructions

							-31-
■Deleting Preset Positions
1. Move the cursor to PRESET 1 and select the position
number to be deleted with the joystick.
2. Press the CAM (SET) button to display the preset
setting menu.
3. Move the cursor to DEL and press the CAM (SET)
button.
This deletes the preset position and the PRESET
NUMBER SET menu appears. The * mark on the
right of the number disappears.
Note:
Your selected preset number is cancelled only in
the SEQ and SORT mode. The previously set
parameters (for PAN, TILT positions, etc.) are not
changed. If you want to change these parame-
ters, you must set them again.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFFOFF
OFF   
OFF
AUTO PAN
ON
     PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
DWELL TIME
SCENE FILE
PRESET SPEED
RET   DELON 
ALC 
10S
1
••••••••|
L       H
 ** PRESET NUMBER SET **
  2
  6
 10
 14
 18
 22
 26
 30   1*
  5
  9
 13
 17
 21
 25
 29
   ID:DOOR
RET  3
  7
 11
 15
 19
 23
 27
 31  4
  8
 12
 16
 20
 24
 28
 32
■Home Position Setting (HOME
POSITION)
1. To set a position number for the home position
Move the cursor to HOME POSITION and select a
desired position number with the joystick.
2. Select OFF if you are not using the home position
function.
■Self Return Setting (SELF
RETURN)
You can set a return time and one of operation modes
with this menu.
1. Move the cursor to SELF RETURN, select a return
time from among the following with the joystick and
press the CAM (SET) button to confirm your selec-
tion.
MIN stands for minute(s).
2. Select an operation from among the following with
the joystick and press the CAM (SET) button to con-
firm your selection.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFF15
OFF
OFF
AUTO PAN
ON
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFF 1
OFF 
OFF
AUTO PAN
ON
2MIN 3MIN 5MIN 10MIN
60MIN
30MIN 20MIN1MIN
OFF
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFF 1
10MIN AT
OFF
AUTO PAN
ON
AT HP AP SQ
SROFF
PT 
						

							This determines the starting point and the cursor
moves to END.
(3) Move the joystick to select a panning endpoint
and press the CAM (SET) button.
This determines the endpoint and the cursor
moves to POSITION.
4. To set a panning speed
Move the cursor to SPEED, and set a panning
speed with the joystick.
The panning speed increases when the joystick is
moved to the right, and decreases when it is moved
to the left.
Caution:
If the panning range is changed after the camera
has not panned for a long time or has been panning
in the same panning range, the picture may not be
clear or noise may appear. In such cases, pan the
camera fully several times.
If this does not eliminate the problem, refer servicing
to qualified service personnel.
5. To set ENDLESS to ON/OFF
Move the cursor to ENDLESS, and select ON or OFF
with the joystick.
ON:The camera pans from the starting point to the
endpoint, and keeps rotating in the same direc-
tion to return to the starting point. Set PAN LIMIT
to OFF before ENDLESS is set to ON. 
    ** AUTO PAN **
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
ZOOM LIMIT
RETSTART
END
••••|••••
L       H
OFF
1S
OFF
OFF
    ** AUTO PAN **
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
ZOOM LIMIT
RETSTART
END
••••|••••
L       H
OFF
1S
OFF
OFF
    ** AUTO PAN **
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
ZOOM LIMIT
RETSTART
END
••••|••••
L       H
ON
1S
OFF
OFF
-32-
■Auto Mode Selection (AUTO
MODE)
1. To set auto mode
Move the cursor to AUTO MODE and select a mode
with the joystick. Modes change as follows:
2. When AUTO PAN is selected, set details as follows:
Move the cursor to AUTO PAN 
Oand press the
CAM (SET) button to display the AUTO PAN setting
menu.
3. To set a panning starting point and panning end-
point
Follow the steps below.
(1) Move the cursor to POSITION and press the
CAM (SET) button. The cursor moves to START.
(2) Move the joystick to select a panning starting
point and press the CAM (SET) button.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFFOFF
OFF
AUTO PAN
AUTO PAN
ON
OFFSEQSORTAUTO PAN PATROL
    ** AUTO PAN **
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
ZOOM LIMIT
RETSTART
END
••••|••••
L       H
OFF
1S
OFF
OFF
    ** AUTO PAN **
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
ZOOM LIMIT
RETSTART
END
••••|••••
L       H
OFF
1S
OFF
OFF 
						

							-33-
OFF:The camera pans from the starting point to the
endpoint, and rotates backward to the starting
point.
This movement is repeated over and over.
6. To set a dwell time
Move the cursor to DWELL TIME and select a dwell
time with the joystick.
Dwell time changes as follows: (unit: s)
7. To set pan limit ON/OFF
Move the cursor to PAN LIMIT and select ON or OFF
with the joystick.
The factory default setting is OFF.
ON:Manual pan is limited from the starting point to
the endpoint specified by position setting. Set
ENDLESS to OFF before PAN LIMIT is set to ON.
OFF:Manual pan is not limited.
Note: 
When ON is selected for PAN LIMIT, manual pan
moves the camera away from the other side
(PAN LIMIT) of the start-end range.
8. To set zoom limit ON/OFF
Move the cursor to ZOOM LIMIT and select ON or
OFF with the joystick.
ON:Limits the manual zoom operation by following
the procedure below.
(1) Move the cursor to ZOOM LIMIT, select ON and
press the CAM (SET) button.
The ZOOM LIMIT setting menu appears.
    ** AUTO PAN **
POSITION
SPEED
ENDLESS
DWELL TIME
PAN LIMIT
ZOOM LIMIT
RETSTART
END
••••|••••
L       H
OFF
1S
OFF
OFF
0S
1S2S3S
30S 5S10S20S
    ** ZOOM LIMIT **
ZOOM
RET→PUSH SET
(2) Move the cursor to ZOOM, press the CAM (SET)
button, move the joystick to settle the ZOOM
position and return to the AUTO PAN menu. The
manual zoom operation is not available in the
TELE direction beyond the settled zoom position.
OFF:Does not limit the manual zoom operation.
Notes:
•When the panning, tilting, zooming or focusing in
the SEQ, SORT or PATROL mode is controlled
manually, the auto mode function should be can-
celled.
To activate the auto mode, select the desired
auto mode again or set a time for SELF RETURN
in the SET UP menu.
•When 0S is selected, the camera stops without
dwelling and starts.
•Auto refreshing may be activated during the
patrol play or the auto mode to calibrate the lens
position.
■Auto Pan Key Setting (AUTO PAN
KEY)
This is used for assigning one of the following auto
functions to the AUTO button on the controller. Pressing
the AUTO button activates the assigned function after
this setting.
•Move the cursor to AUTO PAN KEY and select an
auto function with the joystick.
The factory default setting is AUTO PAN.
The mode changes as follows:
    ** ZOOM LIMIT **
ZOOM
        U ZOOM D
RET
→PUSH SET
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFFOFF
OFF
OFF
AUTO PAN
ON
SEQSORT PATROL
AUTO PAN 
						

							●Password Lock (PASSWORD LOCK)
Caution:
For security, do not operate your VCR for recording
while the password menus are displayed on the
monitor.
A 3-digit number is used for a password to limit
access to all settings.
1. Move the cursor to PASSWORD LOCK, then select
ON or OFF with the joystick.
Note:
ON or OFF can be selected only after going
through the password verification.
OFF:You can change all settings.
ON:You cannot change settings at all nor operate
AUTO PAN, SEQ, SORT, and PATROL.
2. Press the CAM (SET) button.
Password Verification
3. The password verification menu appears.
3-1 Select a numeral for the first digit with the joy-
stick, and press the CAM (SET) button. Though
the entered password is not displayed, the up-
arrow moves one character to the right.
3-2 Repeat the above step for the 2nd and 3rd dig-
its.
Default: 123
3-3 The cursor moves to OK after all the three digits
have been entered. Unless you want to change
the password, press the CAM (SET) button.
If the correct password is entered, the screen
returns to SET UP MENU. ON and OFF settings
are the same as made on the SET UP MENU
menu is as set in step 1.
If a wrong password is entered, the screen
returns to the verification menu. Repeat steps 3-1
to 3-3 to verify the password.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK ONOFF
OFF
OFF
AUTO PAN
ON
      ** PASSWORD? **
   0 1 2 3 4 5 6 7 8 9
          . . .
          
↑
OK  RESET
NEW PASSWORD
RET        
-34-
AUTO PAN:Assigns the auto panning function to
the button.
SEQ: Assigns the SEQUENCE function to the but-
ton.
SORT:Assigns the SORT function to the button.
PATROL:Assigns the PATROL PLAY function to the
button.
Note:
AUTO PAN LED on the controller does not light if
something other than AUTO PAN is assigned.
AUTO PAN does not stop with the AUTO PAN
button.
If PASSWORD LOCK is set to ON, you cannot
operate AUTO PAN, SEQ, SORT, and PATROL
even by pressing the AUTO button. 
■Digital Flip Setting (DIGITAL FLIP)
Move the cursor to DIGITAL FLIP and select ON or OFF
with the joystick.
OFF:The tilt range is limited from 0 ° to 90 °.
ON:The digital flip function allows the tilt angle to
widen up to 180 °. The image on the monitor
screen is flipped horizontally and vertically at the
tilt angle of approx. 135 ° (If the camera is
installed on a ceiling).
Note:
The tilt range narrows from 0 ° to 90 ° if PAN
LIMIT is set to ON.
Notes:
•Digital flip functions while moving the joystick down-
wards. In case of moving the joystick to other direc-
tions, it does not function.
•When OFF is selected for DIGITAL FLIP, the follow-
ing operations are required to move the camera
180 ° vertically.
1) Move the joystick downwards to aim the camera
down.
2) Move the joystick to the right or left to rotate the
camera 180 ° horizontally.
3) Move the joystick upwards.
•To set the preset position directly from WV-CU360
System Controller, it is temporarily required to set
both the electronic zoom function and digital flip
function to OFF.
Tilt range setting is disabled between 90 ° and 185 °.
   ** SET UP MENU **
PRESET 1 
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFFOFF
OFF
OFF
AUTO PAN
ON 
						

							-35- 3-4 To cancel an incomplete password, move the
cursor to RESET, and press the CAM (SET) but-
ton. The screen returns to the verification menu. 
3-5 To return to the SET UP MENU menu without ver-
ifying the password, move the cursor to RET, and
press the CAM (SET) button.
New Password
4. To change the password in step 3-3 above, move
the cursor from OK to NEW PASSWORD, then press
the CAM (SET) button. NEW PASSWORD menu
appears.
Note:
The NEW PASSWORD menu is accessible only
after the verification has been completed.
The up-arrow mark appears indicating the first digit
on the first line.
4-1 Enter a new three-digit password in the same
way as in steps 3-1 to 3-2.
4-2 The cursor moves to OK after all the three digits
have been entered. Press the CAM (SET) button
to move the cursor to the first digit on the second
line.
4-3 Enter the same password as the one you have
entered on the first line.
4-4 The cursor moves to OK. Press the CAM (SET)
button. If the new password is successfully
entered, the screen returns to SET UP MENU.
4-5 Retry steps 4-1 to 4-4. If the first entry for the
password is different from the second one, the
screen returns to the NEW PASSWORD? menu.
4-6 To return to the SET UP MENU menu without
changing the password, move the cursor to RET,
and press the CAM (SET) button.
   **  NEW PASSWORD? **
   
   0 1 2 3 4 5 6 7 8 9
          . . .
          
↑          . . .
         
OK  RESET
RET        
■Special 1 Menu Setting
(SPECIAL 1)
●Privacy Zone (PRIVACY ZONE)
Up to 8 unwanted zones can be masked on the monitor
screen.
1. Move the cursor to PRIVACY ZONE and select ON
or OFF with the joystick. Press the CAM (SET) button
to display the ZONE NUMBER setting menu.
ON:Preset privacy zones are veiled on the monitor
screen.
OFF:The veiling function does not work.
2. Select a zone number with the joystick, and press
the CAM (SET) button.
•A zone number followed by * (asterisk) indicates
that the zone has already been registered.
•When a zone number having no * is selected, the
picture is zoomed out (WIDE).
•When a registered zone number is selected, the
camera moves to the preset position. Note that if
you move PAN/TILT, ZOOM/FOCUS or ZONE
SCALE in that position, the registered zone number
having (*) is cancelled.
•The zone frame appears in the center of the screen
if 3 or fewer mask areas exist in that picture and if
the zone number is not registered yet.
•Up to 4 zones can be registered on the fully dis-
played screen (WIDE). 
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
** ZONE NUMBER 1*/8 **
  
 
 
 
 
 
 
 
 
RET
** ZONE NUMBER 1*/8 ** 
PAN/TILT     →PUSH SET 
ZOOM/FOCUS   →PUSH SET 
 
 
 
 
 
ZONE SCALE   ••••|•••• 
SET DEL      L       H
RET 
						

							Moving the joystick in the L direction decreases
the zone frame, and moving it in the H direction
increases it. However, the aspect ratio is fixed at
3 to 4.
The privacy zone setting has been completed.
The menu returns to the ZONE NUMBER setting
menu.
3-6
•To complete new settings and repeat other set-
tings, move the cursor to SET and press the
CAM (SET) button. The ZONE NUMBER setting
menu reappears.
•To cancel new settings and return to the SPE-
CIAL 1 menu, move the cursor to DEL and press
the CAM (SET) button. New settings are not reg-
istered.
•To complete new settings and return to the SPE-
CIAL 1 menu, move the cursor to RET and press
the CAM (SET) button.
●Proportional Pan/Tilt (PROPO. P/T)
Move the cursor to PROPO. P/T and select either ON or
OFF with the joystick.
Factory default setting: ON
ON:Pan/tilt speed is in inverse proportion to the
zoom ratio as follows:
Zoom ratio Speed level
x1 7 (fastest)
x2 5
x4 3
x8 1
x15 or more 0 (slowest)
*  The speed level values are approximate.
OFF:The speed is constant at the fastest level
regardless of the zoom ratio. 
** ZONE NUMBER 3*/8 **  
PAN/TILT     →PUSH SET 
ZOOM/FOCUS   →PUSH SET 
 
 
 
 
ZONE SCALE   ••••|•••• 
SET DEL      L       H
RET
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
-36- •When 5 privacy zones or more are framed on the
displayed screen in the same time, the whole screen
will be masked. In this case, diminish the number of
the zones and set the privacy zones larger.
•The privacy zone may appear on the monitor screen
depending on the direction of the camera.
•The privacy zone function will not work at start-up
immediately after turning the power on.
3. To register a new zone
3-1 For PAN/TILT, move the cursor to PUSH SET and
press the CAM (SET) button.
3-2 Adjust the pan and tilt position so that the
desired position comes into the zone frame with
the joystick.
3-3 For ZOOM/FOCUS, move the cursor to PUSH
SET , and press the CAM (SET) button.
3-4 Adjust zoom and focus, and press the CAM
(SET) button.
Zoom can be adjusted within the range of 1 to 10
magnifications.
3-5 Move the cursor to ZONE SCALE, and move the
joystick to the right or left to adjust the zone
frame. Press the CAM (SET) button after the
adjustment.
** ZONE NUMBER 3*/8 **  
PAN/TILT     →PUSH SET 
ZOOM/FOCUS   →PUSH SET 
 
 
 
 
 
ZONE SCALE   ••••|•••• 
SET DEL      L       H
RET
** ZONE NUMBER 3*/8 **  
PAN/TILT     →PUSH SET 
ZOOM/FOCUS   →PUSH SET 
     U TILT D/L PAN R 
 
 
 
 
ZONE SCALE   ••••|•••• 
SET DEL      L       H
RET
** ZONE NUMBER 3*/8 **  
PAN/TILT     →PUSH SET 
ZOOM/FOCUS   →PUSH SET 
   U ZOOM D/L FOCUS R 
 
 
 
 
ZONE SCALE   ••••|•••• 
SET DEL      L       H
RET 
						

							-37-
●Area Title (AREA TITLE)
Up to 8 area titles can be added in specific positions.
1. Select ON (NESW), ON (USER) or OFF with the joy-
stick.
ON (NESW):An area title is displayed for indicating
the camera direction: North (N), North-East (NE),
East (E), South-East (SE), South (S), South-West
(SW), West (W) and North-West (NW).
ON (USER):A user customized area title appears in
a maximum of 16 characters.
OFF:Area title does not appear.
Factory default setting: OFF
2. Press the CAM (SET) button. A submenu appears
except when OFF is selected.
Settings for ON (NESW)
1. Move the cursor to PUSH SET for PAN/TILT, and
press the CAM (SET) button. PAN/TILT is highlight-
ed and U TILT D/L PAN R appears.
2. Turn the camera north with the joystick, and press
the CAM (SET) button. The origin of the direction
(North) is set.
Note:
Area titles are highlighted until the origin is set.
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
→PUSH SET→PUSH SET
 ** DIRECTION(NESW) **
PAN/TILT
ZOOM/FOCUS
POSI
           +           N
RET
→PUSH SET
→PUSH SET→PUSH SET
 ** DIRECTION(NESW) **
PAN/TILT
ZOOM/FOCUS
POSI
    U TILT D/L PAN R
           +
           N
RET
3. Move the cursor to PUSH SET for ZOOM/FOCUS,
and press the CAM (SET) button. ZOOM/FOCUS is
highlighted and U ZOOM D/L FOCUS R appears.
4. Adjust the zoom or focus with the joystick.
5. Move the cursor to POSI 
O, and press the CAM
(SET) button. The area title position appears on the
monitor screen. If needed, change the display posi-
tion with the joystick, and press the MON (ESC) but-
ton.
An area title always appears under the camera ID.
If the camera ID and an area title are set to be
shown in separate positions, the area title appears
above the camera ID.
6. Move the cursor to RET, and press the CAM (SET)
button. The SPECIAL 1 menu appears again.
Setting for ON (USER)
If ON (USER) is selected on the SPECIAL 1 menu,
the AREA TITLE (USER) menu appears. The screen
has a number column and title column above RET
and RESET.
Note:
An area number followed by an asterisk * has
already been preset.
→PUSH SET→PUSH SET
 ** DIRECTION(NESW) **
PAN/TILT
ZOOM/FOCUS
POSI
   U ZOOM D/L FOCUS R
           +
           N
RET
     
FLOOR 1
N
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET 
						

							To Quit Editing
•To return to the AREA TITLE menu, move the cursor
to RET, and press the CAM (SET) button.
•To cancel one area title, move the cursor to RESET
in the AREA TITLE menu, and press the CAM (SET)
button.
•To return to the SPECIAL 1 menu, move the cursor
to RET, and press the CAM (SET) button.
•To erase all the area titles, move the cursor to
RESET in the AREA TITLE (USER) selection menu,
and press the CAM (SET) button.
Notes:
•An area title appears under the camera ID if both
are set in the same position. If the setting is dif-
ferent, they appear in the area title position.
•In case of sharing a common subject in a scene
of other camera number, the nearest area title
appears while the camera direction deviates
within 45 ° from the set position. If two or more
area numbers are set in the same position, the
title of the highest number appears.
●Patrol-learn and Patrol Play (PATROL)
A routine of manual operations can be stored for 1
minute at the maximum and reproduced repetitively.
PATROL
1. Set the following parameters for the patrol-learn
starting position. These parameters are stored when
the patrol-learn mode starts.
•PAN/TILT/ZOOM/FOCUS
•IRIS
•SHUTTER
•AGC
•SENS UP
•WHITE BALANCE
•IMAGE HOLD
•AREA TITLE 
     
FLOOR 1
NORTH
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         PLAY
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
-38- 1. To select a camera direction, move the cursor to the
desired number, and press the CAM (SET) button.
The direction menu of the selected number appears.
2. Adjust PAN/TILT, ZOOM/FOCUS and display the
position in the same way as AREA TITLE, DIREC-
TION (NESW). See page 37.
3. To add a user-customized title, move the cursor to
the title of the desired number, and press the CAM
(SET) button. The AREA TITLE menu of the selected
number appears.
Area Title Editing
1. Move the cursor to the desired character in the
character field with the joystick, and press the CAM
(SET) button.
2. The selected character appears in the editing field
and the blinking cursor moves one position to the
right.
3. Repeat steps 1 and 2 until one area title is complet-
ed.
4. Move the cursor to POSI 
O, and press the CAM
(SET) button. The area title appears on the monitor
screen. If needed, change the display position with
the joystick, and press the MON (ESC) button.
  ** AREA TITLE(USER) **
       NORTH
 2
 3     EAST
 4     SOUTH-EAST
 5     SOUTH
 6     SOUTH-WEST 7
 8     NORTH-WEST
RET  RESET
1* 
→PUSH SET→PUSH SET
 ** DIRECTION(USER) 1 **
PAN/TILT
ZOOM/FOCUS
            +          NORTH
RET  DEL
     AREA TITLE 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
         POSI RET RESET
    ................
     
						

							-39- •DIGITAL FLIP
•PRIVACY ZONE
•CAMERA ID
•PROPO.PT
•PAN LIMIT
•ZOOM LIMIT
•TILT ANGLE
•CLEANING
After starting the patrol-learn, the following manual
operations are stored.
•PAN/TILT/ZOOM/FOCUS operation
•IRIS operation
•Preset positioning
The auto focus function is disabled during the patrol
operation. Under such circumstances, the camera
goes out of focus when zooming in with WIDE
selected resulting from a characteristic of a zoom
lens. For storing the zoom operation, start with the
TELE mode keeps the camera in focus.
The patrol operation ranges from the horizontal
direction to the downward direction. The digital flip
function is disabled (page 34).
2. Open the SET UP menu and move the cursor to
SPECIAL 1. For PATROL, select LEARN, PLAY or
STOP with the joystick.
The factory default setting is STOP.
LEARN:A series of manual operations is stored.
PLAY:Stored operations are reproduced.
STOP:LEARN or PLAY is not activated.
PATROL LEARN with a Controller Having PATROL
Button
1. Press the PATROL button and the CAM (SET) button
simultaneously to start patrol-learn. The setup menu
displays LEARNING(60S), and the starting points
are stored. (unit: s)
2. Operate patrol-learn manually. The operation data is
stored. The countdown to complete learning is dis-
played.
3. To stop patrol-learn, press the PATROL STOP but-
ton. 
Patrol-learn with a Controller not Having the
PATROL Button
1. Close the SET UP or SPECIAL 1 menu to start
PATROL LEARN. Starting point parameters are
stored and LEARNING(60S) is displayed on the
monitor.
LEARNING(60S)
2. Operate patrol-learn manually.
3. Open the SET UP menu to stop learning.
Notes:
•It is recommended to set PAN LIMIT to ON for
patrol-learn. Otherwise PAN LIMIT is invalid in
playback. 
•If the power fails in the patrol-learn mode, start
the patrol-learn function again from the starting
point.
•LEARN also stops 1 minute after starting if the
memory is full.
•Auto refreshing may be activated in the patrol
play mode or the auto mode to calibrate the lens
position.
Patrol Play with a Controller Having the PATROL
Button
1. Press the PATROL PLAY button. The camera turns
to the starting point and reproduces the operations
stored in the memory. Iris operation is valid only in
the playback mode.
2. Press the PATROL STOP button and PROGRAM
button simultaneously to stop playback or press any
manual operation button (e.g., PAN/TILT/ ZOOM/
FOCUS) except the iris buttons.
Patrol Play with a Controller not Having the PATROL
Button
1. Select patrol play in the setup menu, and then close
the menu. The camera turns to the starting point and
the operations stored in memory are reproduced.
Iris operation is valid only in the playback mode.
2. Open the SET UP menu, or press any of manual
operation button (e.g., PAN/TILT/ZOOM/FOCUS)
except the iris buttons to stop playback.
Patrol Play with the AUTO PAN Button
1. If the PATROL PLAY function is assigned to the
AUTO PAN button, press the AUTO PAN button to
turn the camera back to the starting point and to
reproduce the operation data stored in the memory.
2. To stop playback, press the PATROL STOP button
or any manual operation button (e.g., PAN/TILT/
ZOOM/FOCUS) except the iris buttons.
Notes: 
•In the patrol play mode, the camera movement may
occasionally deviate from the entered routine when
the routine includes a move to a preset position. If
this happens, re-enter the routine of manual opera-
tions for patrol-learn.
•In the patrol play mode, black and white automatic
switching does not work.
•In the patrol play mode, when the power of the con-
troller is turned on or off, the patrol play stops. In this
case, press the PATROL PLAY button again. (If
SELF RETURN is set to ON, the patrol play will start
again after elapsing the setting return time.) 
						

							CNT-CLS 1, 2 (Output)
Two contact closure signals (Open collector type) are
output through the Alarm Output connector.
1. Move the cursor to CNT-CLS 1, and select OFF,
ALARM or AUX 1 with the joystick.
The factory default setting is OFF.
When ALARM is selected, TIME OUT appears.
Select an appropriate duration from among 100 MS,
200 MS, 1000 MS (1 s), 2000 MS (2 s) and 4000 MS
(4 s) with the joystick. (unit: s)
The factory default setting is 100 MS. (unit: ms)
Note:
The shorter the duration, the more frequent will
be the detection output.
2. Move the cursor to CNT-CLS 2, then select OFF,
AUX 2 with the joystick.
The factory default setting is OFF.
OFF:Contact closure signals are deactivated.
ALARM:Available for CNT-CLS 1 only. A motion
detection signal is output.
AUX 1(2):An alarm signal is output when the cam-
era receives a command from the controller.
Note:
It is recommended to set the connected external
device to ignore the shorter alarm outputs of 90
ms or less from the camera.
COAXIAL ALARM OUT
Alarm output signals are supplied through the coaxial
cable.
1. Move the cursor to COAX ALM OUT and select ON
or OFF.
2. Press the CAM (SET) button.
The factory default setting is OFF.
ON:The camera sends an alarm output signal after
it turns to a preset position.
OFF:The camera does not send an output signal.
Notes:
•The camera ignores alarm inputs during manual
operation.
•To download or upload preset data to the system
controller, select “OFF”.
-40-
●Alarm Input/Output (ALARM IN/OUT)
Move the cursor to ALARM IN/OUT, and press the CAM
(SET) button. The ALARM IN/OUT submenu appears.
Note:
While the camera is in the AF mode or the lens
moves between WIDE and TELE, alarm input may
be ignored if several alarm inputs are received in
succession.
ALARM IN 1-4
Alarm input signals are supplied from external devices
through the ALARM IN connector to turn the camera to
a preset position.
1. Move the cursor to ALARM IN 1* and select a preset
position or OFF with the joystick, then press the
CAM (SET) button.
The factory default setting is OFF.
*Set ALARM IN 2, 3 and 4 in the same way as
ALARM IN 1.
1 POSI, 2 POSI, 3 POSI and 4 POSI:Preset posi-
tion. If an alarm input is received, the camera
turns to a preset position, and sends an alarm
output signal. The position number corresponds
to the alarm input number (1-1, 2-2, 3-3 and 4-4).
OFF:The camera ignores alarm inputs.
    ** SPECIAL 1 **
PRIVACY ZONE   OFF
PROPO.P/T      ON
AREA TITLE     ON(USER)
PATROL         STOP
ALARM IN/OUT
CLEANING       OFF
EL-ZOOM        ON
PRESET ALM     OFF
IMAGE HOLD     OFF
TILT ANGLE     0°
RET
   ** ALARM IN/OUT **
ALARM IN 1
ALARM IN 2
ALARM IN 3
ALARM IN 4
 
CNT-CLS 1
 TIME OUT
CNT-CLS 2
COAX ALM OUT
RET         OFF 
 OFF 
 OFF
 OFF
   
 OFF  
 100MS 
 OFF  
 OFF