Panasonic Color Cctv Camera Wv Cp500 Operating Instructions

21
Configure alarm notification
Follow the procedure below. Step 1
Move the cursor to "i-VMD" and press the setting button. 
  →  The "i-VMD SETUP" screen appears. 
Step 2
Move the cursor to "ALARM" and configure alarm notification. 
CONT (default): Continues to send alarm signals upon detection. 
1TIME: Sends an alarm signal only once (100 ms) at detection start. 
   **i-VMD SETUP**(1)      
MOTION DET
OBJECT DET     OFF
SCENE CHANGE   OFF
INDICATOR      OFF
ALARM          CONT...

22
Camera system setting [SYSTEM SETUP]
Performs the settings relating to the camera system such as synchronization, alarm input/output terminal, and privacy zone. 
The following settings can be configured on the "SYSTEM SETUP" screen displayed from the top screen. Refer to page 5 for how 
to call up the screen. 
10. Synchronization method selection [SYNC]
This unit supports the following 3 types of synchronization methods, and one of the following is selected. 
 (1)  Multiplexed vertical drive...

23
Step 1
Set "SYNC" to "LL" and press the setting button. 
  →  The "SYNC" screen appears. 
Step 2
Connect  the  video  output  signal  and  external  synchronizing  input  signal  of  the  camera  to  a  2-input  oscilloscope,  and  move  the 
cursor to "COARSE". 
Step 3
Adjust the oscilloscope to the vertical rate, and extend the vertical synchronizing part of the oscilloscope. 
Move the cursor horizontally with use of the right or left button to roughly adjust the...

24
Configure the settings relating to the alarm output terminal
Select the alarm output operation. Follow the procedure below. Step 1
Move the cursor to "ALARM IN/OUT" and press the setting button. 
  →  The "ALARM IN/OUT" screen appears.
Step 2
Move the cursor to "ALARM OUT" and select the alarm output terminal operation from the following. 
OFF (default): Does not perform terminal output. 
ALARM:  The  alarm  output  will  be  performed  upon  a  i-VMD  detection.  The  alarm...

25
Step 2
Move the cursor to the number at the right of the title and select the z\
one number using the right or left button.  
Step 3
Move the cursor to "POSITION" and press the setting button. 
Step 4
Use the up, down, right, and left buttons to determine the left upper position of the zone to be set and press the setting button. 
Step 5
Use the up, down, right, and left buttons to determine the lower right position of the zone to be set and press the setting button. 
  →  The asterisk mark...

26
14. Electronic zoom setting [EL-ZOOM]
Select "On" or "Off" to determine whether or not to use the electronic zoom. 
When "ON" is selected, the zoom factor and the panning/tilting settings \
can be configured. 
ON: Uses the electronic zoom. 
OFF (default): Does not use the electronic zoom. 
Follow the procedure below. Step 1
Move the cursor to "EL-ZOOM", select "ON" and press the setting button. 
  →  The "EL-ZOOM" screen will be displayed. 
Step 2
Move...

27
Back focus setting [BACK-FOCUS SETUP]
Selects  the  back  focus  setting  type  and  performs  fine  adjustment.  The  following  setting  can  be  configured  on  the  "BACK-
FOCUS SETUP" screen displayed from the top screen. Refer to page 5 for how to call up the screen. 
The lens adjustment (☞ Installation Guide) shall be performed before the back focus adjustment. 

The back focus adjustment is performed by changing the distance between the lens and focal point. 
Follow the procedure...

28
Step 3
Move the cursor to "C/L ← → B/W" and select the back focus adjustment type from the following: 
AUTO  (default):  Adjusts  the  back  focus  function  automatically  and  corrects  out  of  focus  when  switching  between  color  and  black-and-white images. 
PRESET:  Performs  the  preset  movement  to  each  specified  back  focus  position  when  switching  between  color  and  black-and-
white  images.  The  preset  position  is  the  back  focus  position  specified  last  time,...

29
Special menu setting [SPECIAL SETUP]
The  special  menu  setup  is  performed  including  the  setting  of  the  camera  image  quality  and  the  communication  configuration 
when  a  receiver  is  used.  The  following  settings  are  to  be  configured  on  the  "SPECIAL  SETUP"  screen  displayed  from  the  top 
screen. Refer to page 5 for how to call up the screen. 
Chroma level adjustment [CHROMA GAIN]
Use	the	right	 or	left	 button	 to	adjust	 the	color	 density	 of	the	 camera...

30
Flaw compensation [PIX OFF]
Flaws in the displayed camera image are corrected. Up to 16 points can be corrected. 
Follow the procedure below.  Step 1
Move the cursor to "PIX OFF" and press the setting button. 
  →  The "PIX OFF" screen appears. 
Step 2
Select a number (1 to 16) with which a pixel compensation point is registered and press the setting button. 
  →  The pixel compensation positioning screen appears. 
Step 3
Use the up, down, right, and left buttons to move the crosshair...