Panasonic Color Cctv Camera Wv Cp500 Operating Instructions

11
When not using the SUPER-D5 function
Follow	the	procedure	below.Step 1
When	the	SUPER-D5	function	is	set	to	"OFF",	bright	areas	of	an	image	are	masked	to	facilitate	the	visibility	of	dark	areas.	
Move	the	cursor	to	"MASK	SET"	and	press	the	setting	button.	
  →	 The	mask	setting	screen	appears.	
Step 2
Mask	bright	areas.	
Use	 the	up,	 down,	 right,	and	left	buttons	 to	select	 an	area	 to	be	 masked	 and	press	 the	setting	 button.	 When	the	selected	 area	is	
masked,	 the	masked	 area...

12
When the SUPER-D5 function is set to "OFF": OFF (1/60) (default), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 00\
0, and  1/10 000
When the SUPER-D5 function is set to "ON" or "ON(i-VMD)": OFF (1/60) (default), 1/100
Note:
	 •	 When	"ALC/ELC"	is	set	to	"ELC"	or	"ALC+"	(+	page	9),	"---"	appears	and	the	electronic	shutter	function	cannot	be	activated.
	 •	 If	the	controller,	WV-CU254	or	WV-CU204	is	used,	SW	LED	and	the	status	of	"SHUTTER"...

13
Note:
   If the situation meets one of the following or other, color may not be accurately reproduced. 
	 •	 The	subject	is	mostly	highly-colored.	
	 •	 The	photographic	atmosphere	is	under	the	bright	blue	sky	or	at	nightfall.	
	 •	 The	illumination	of	the	light	illuminating	the	subject	is	insufficient.	
ATW2:  Activates  the  sodium  lamp  automatic  color  temperature  tracking  mode.  The  camera  automatically  achieves  an  optimal 
white balance under the sodium lamp. The adjustment of the color...

14
Manual fine adjustment of white balance
The  white  balance  is  manually  fine  adjusted  after  white  balance  automatically  adjustment  in  the  automatic  color  temperature 
tracking mode (ATW1, ATW2) or automatic white balance control mode (AWC). 
Follow the procedure below. Step 1
Set "WHITE BAL" to "ATW1", "ATW2" or "AWC" and press the setting button. 
  →  The fine adjustment screen appears. 
Step 2
Move the cursor to "R" and "B" and use the...

15
Step 1
Move the cursor to "BW MODE" and select the black-and-white control from the following: 
AUTO1  (default):  Automatically  toggles  between  color  and  black-and-white  images  in  accordance  with  the  screen  brightness  (illuminance). The black-and-white mode is selected for dark images, a\
nd the color mode is selected for bright images. 
AUTO2: Uses a near-infrared light source at nighttime. 
ON: Displays black-and-white images. 
OFF: Displays color images. 
Note:
	 •	 The	 auto...

16
9. i-VMD setting [i-VMD]
The  intelligent  motion  detection  function  allows  the  camera  to  detect  motion  and  appearance/disappearance  of  an  object  or 
scene  change  with  the  camera.  Detection  of  motion  and  appearance/disappearance  of  an  object  or scene  change  with  the 
camera can be announced by issuing an alarm signal or displaying a frame on the screen. 
Important:
	 •	 The	 following	 circumstances	 may	result	 in	detection	 failure	or	false	 detection:	 Adjusting	the...

17
Detect motion of objects
Move the cursor to "MOTION" and select from the following. 
ON: Provides an alarm signal when motion is detected. 
OFF (default): Does not detect motion. 
Detect objects that move continuously within a specified period
Move the cursor to "LOITERING" and select the duration from the following:
When a continuously moving object is detected within a specified period,\
 an alarm signal is issued. 
OFF (default)/ON (5 s)/ON (10 s)/ON (20 s)/ON (30 s)/ON (40 s\
)/ON...

18
Perform the settings relating to the detection of appearance/disappearan\
ce of stationary objects
Perform the settings relating to the detection of appearance/disappearance of stationary objects as follows. Up to 4 appearanc-
es/disappearances of stationary objects can be simultaneously detected. However, use of the scene change detection function 
decreases the maximum simultaneous detectable appearances/disappearances of \
stationary objects to 3. 
Follow the procedure below. 
Step 1
Move the...

19
Set the detection areas
Set the detection areas for motion detection and the detection of appearance/disappearance o\
f stationary objects. 
Up to 2 detection areas can be set. 
Follow the procedure below. Step 1
Move the cursor to "AREA" and select "SETUP", and then press the setting button. 
  →  The "AREA" screen appears. 
Step 2
Move the cursor onto the number to select the area number using the right or left button. 
Step 3
Move the cursor to "POSITION" and press...

20
Setting of scene change detection 
This  function  detects  a  change  in  the  subject  state  that  occurs  by  covering  the  camera  with  a  cloth,  a  cap,  or  others,  or  by 
changing the camera direction largely. 
Follow the procedure below. Step 1
Move the cursor to "i-VMD" and press the setting button. 
  →  The "i-VMD SETUP" screen appears. 
Step 2
Move the cursor to "SCENE CHANGE" and select from the following. 
ON: Provides an alarm signal when scene change is...