Panasonic Color CCTV Camera Wv Cf624 Wv Cf634 Installation Guide

21
•	Subject	with	large	illuminance	change	 
•	Subject	with	low	illuminance	 
•	Too	bright	or	reflective	subject	 
•	Subject	through	a	window	 
•	Place	where	the	lens	easily	becomes	dirty	 
•	Subject	with	less	contrast	such	as	white	wall	 
•	Subject	with	remarkable	depth	 
•	Subject	with	heavy	flicker	 
•	Subject	with	horizontally	parallel	lines	such	as	a	shutter

1 Loosen the zoom knob and adjust to the best view angle between TELE and WIDE.
Note:
 •	The	focus	may	not	be	adjusted	smoothly	when	the	zoom...

22
Attaching the dome cover
1  Align the mark with [|] on the dome cover, 
and then install the dome cover. 
Mark
Mark [|] 
2 Adjust the orientation of the dome cover. 
Turn	the	enclosure	clockwise	so	that	the	
mark	aligns	with	[||].	 
Turn  the  dome  cover  to  the  left  or  right 
while viewing the monitor so that the light is 
not	blocked.	
Important: 
•	 Be	sure	to	align	the	mark	with	[||]	when	
adjusting the dome cover. Do not apply 
excessive force, or you may cause  
damage.
3  Turn the dome...

23
AF button
4  Fix the dome cover and camera body with  
the dome cover fixing screw (M3).
(Recommended torque: 0.59 N·m  
{0.43 lbf·ft}) 
5  After finishing the installation,  
completely peel off the protection sheet  
that had been retained on the camera. 
6  Press  the  [AF]  button  again  to  adjust 
the focus. CF634 
For more information, refer to page 21.
Dome coverxing 
screw (M3) 

24
Setup menu
Performing each setting item in the setup menu should be completed in advance to use this unit. Perform  the  settings  for  each  item  in  accordance  with  the  conditions  of  the  camera  shooting area.
List of setup menu
Setup itemDescription
CAMERA ID This item specifies the camera title. The camera title that indicates the camera loca-tion and other information about the camera is created with alphanumeric characters  and symbol, and then displayed on the screen. 
CAMERAPerforms the...

25
Screenshot 2
The  setup  mode  changes  to  "ENABLE",  and  
the setup menu becomes ready to be set. 
Step 3
Move  the  cursor  to  the  item  to  be  set,  and 
press the [SET ] button. 
Screenshot 1
Hold  down  the  [SET]  button  for  about  2  sec-
onds  to  call  up  the  top  screen  of  the  setup 
menu. 
Step 1
Press the [UP] button or the [DOWN] button to  
move the cursor to "END".
Step 2
Press  the  [RIGHT]  button  to  move  the  cursor 
to  "SETUP",  and  press...

26
Screenshot 3
The  selected  setup  screen  in  the  setup  menu  
appears on the screen. 
Note: 
	 •	 If	the	top	screen	of	the	setup	menu	is	
called  up  with  the  operation  buttons,  the  
s e t u p   m o d e   i s   a l w a y s   " D I S A B L E "   t o 
prevent operation errors. 
   To  perform  settings  in  the  setup  menu, 
change the setup mode to "ENABLE". 
	 •	 The	cursor	is	a	reversely	highlighted	part.	 
     
Step 4
Perform the settings for each item.
•	Selection of...

27
Screen transition diagram CF634 
Top screenCAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
SPECIAL  SETUP screen
LANGUAGE SETUP screen 
 MODEL   WV-CF634
CAMERA ID     OFF
CAMERA    
SYSTEM
BACK-FOCUS
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
     **CAMERA ID**   
 
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +- */%$
    SPACE POSI
    RET TOP END RESET
    ................
    **SYSTEM SETUP**...

28
Top screenCAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
SPECIAL SETUP screen
LANGUAGE SETUP screen 
 MODEL   WV-CF624 CAMERA ID     OFFCAMERA   SYSTEM SPECIAL LANGUAGE 
  
 END   SETUP DISABLE
   **LANGUAGE SETUP** 
LANGUAGE      ENGLISH 
 SET  RET TOP END
     **CAMERA ID**         0123456789     ABCDEFGHIJKLM     NOPQRSTUVWXYZ     ().,:;&#!?=     +-*/%$
    SPACE POSI    RET TOP END RESET 
    ................
    **SYSTEM SETUP** 
PRIVACY ZONE  OFF 
SYNC          INT 
STABILIZER    OFF...

29
Blurred image
No image displayed
Cause/solutionReference page Symptom 
Troubleshooting 
Before asking for repairs, confirm the causes with the following table.  
Contact your dealer if a problem cannot be solved even after checking and trying the solution in 
the table or a problem is not described below. 
–
20-21
–
–
–
15-16
18
	•	 Are	the	power	cord	and	coaxial	cable	connected appropriately? →	 Check	whether	the	connection	is	appropriately established.
	•	 Is	the	adjustment	monitor	connected?	 →...

30
Specifications 
WV-CF634WV-CF624
Power source 24	V	AC	60	Hz,	12	V	DC	
Power consumption24 V AC: 2.5 W, 12 V DC: 220 mA 
Image sensor 1/3-type interline transfer CCD
Effective pixels 976 (H)×494 (V) 
Scanning area 4.8 mm (H)×3.6 mm (V) {3/16 inches (H)×5/32 inches (V)}
Scanning system2:1 interlace
Scanning line525 lines
Horizontal	scanning	frequency15.734	kHz
Vertical scanning frequency59.94	Hz
SynchronizationInternal (INT) , Multiplexed vertical drive(VD2)
Horizontal	resolution650 TV lines 
Vertical...