Panasonic Color CCTV Camera Wv Cf624 Wv Cf634 Installation Guide

11
Locally procure the screws 
Screws  are  not  supplied  with  this  product.  
Prepare  the  screws  according  to  the  material, 
structure,  strength  and  other  factors  of  the 
mounting  area  and  the  total  weight  of  objects 
to be mounted. 
Screw tightening 
	 •	 The	screws	and	bolts	must	be	tightened	
w i t h   a n   a p p ro p r i a t e   t i g h t e n i n g   t o rq u e  
according  to  the  material  and  strength  of 
the installation area. 
	 •	 Do	not	use	an	impact	driver.	Failure...

12
Major operating controls and their functions
(This illustration represents WV-CF634.)
1 Video output connector 
Transmits composite video signals. 
2 Mark
This mark is used when the dome cover is  
installed.
3 Lens
4 Focus knob CF634 
  Focus knob (with lock function) CF624

Locks the focus position after focus adjust-
ment.
5  Zoom knob (with lock function) 
Locks the zoom position after zoom adjust- 
ment.
6  Tilting lock screw  
Locks the tilting position. 
7  AF button [AF]CF634 
 page 21.
8...

13
Installation 
placeApplicable mount
bracket Recommended 
screwNumber 
of screwMinimum pull-out 
strength (per 1 pc.)
Ceiling / wall  One-gang junction box 
(locally procured)  M4
2 pcs.196 N {44.06 lbf}
Ceiling / wall  (Direct mounting)  M42 pcs.196 N {44.06 lbf}
Ceiling  WV-Q174 
(approx. 310 g {0.66 lbs}) -
-*1
*1
  Make sure that the installed mount bracket can support more than 5 times of the weight of the 
camera.
When installing the camera on a wall or ceiling, two are two methods as specified...

14
 About the side cable access hole 
If  you  choose  not  to  drill  hole  in  the  wall  or  
ceiling,  but  to  wire  the  camera  with  the  cable 
exposed, cut the cable access hole on the side 
of the dome cover to provide a cable entry.  
Precautions when wiring from the side:  
•	 Remove	the	dust	guard	cap.	Run	the	cable	
through  the  cable  access  hole  and  bend  it 
inward, then reinstall the dust guard cap. 
•	 Move	the	cable	to	one	side	as	shown.	
•	 Be	careful	not	to	pinch	the	cable...

15
Installing the camera directly on a wall or ceiling
Affix the installation template label (accessory) to the ceiling or wall, and use a pen to mark the posi- 
tions of the screws and cable mounting hole in the ceiling or wall. 
Remove the installation template label, and attach the camera with 2 screws (M4, locally procured). 
      29 mm{1-1/8 inches}
 83.5 mm {3-9/32 inches}
21 mm{13/16 inches}
Recommended screw  (M4, 2 pcs.) 
Screws (M4, locally procured)
Side cable  access hole
Cable mounting hole...

16
Important: 
	 •	 The	power	supply	of	24	V	AC/12	V	DC	shall	be	insulated	against	120	V	AC. 
	 •	 The	power	supply	is	automatically	switchover	either	24	V	AC	or	12	V	DC.	No	setting	is	required	
with this camera. 
Cable length and wire gauge 
24 V AC  
The  recommended  cable  length  and  wire  gauge  are  shown  in  the  table  for  reference.  The  voltage  
supplied to the power terminals of the camera should be within 19.5 V AC and 28 V AC.
The	recommended	wire	size	for	24	V	AC	power	cord	is	shown...

17
Installation of camera 
Turn off the power of all related devices before installation.  
1  Remove the camera dome cover.
2 Connect all cables. 
   If necessary, bind the cable with cable tie (locally procured). 
3 Install the camera (The illustration below shows installation using a gang junction box (locally 
procured) ).
   Mount the camera with 2 screws (M4, locally procured). 
Important: 
•	 Be	sure	to	avoid	twisting	the	cables	when	tightening	the	screws.
Note:
•		 When	attached	to	the	ceiling:...

18
1 Connect the ∅3.5 mm miniature plug (mono channel) to the adjustment monitor output jack. 
Important: 
•		This	video	output	is	intended	for	confirmation	of	view	angle,	etc.	during	installation	or	repair	
service, and not for recording or monitoring. 
Note: 
•	 Video	cannot	be	output	through	the	video	output	cable	after	connecting	the	adjustment	
monitor.
2 Pan, tilt and azimuth adjustment 
Important: 
•	 When	adjusting	pan,	tilt	or	azimuth,	do	not	hold	the	lens	of	the	camera.
1	 Adjustment of panning...

19
3 Adjustment of azimuth 
  Adjust	the	azimuth	by	rotating	the	azimuth	
adjuster. (adjustable range: ±100 °) 
Note:
	•	 Adjust	azimuth	so	that	the	image	top	mark	is	facing	“∆”  to  display  the  image  properly  rather 
than upside-down.
Image top mark
TOP mark 
azimuth adjuster
Rotation  angle: +100 º Rotation angle: -100 º
Image top mark 

20
3	Zoom	and	focus	adjustment	
Perform the zoom and focus adjustments at the same time as pan and tilt adjustments (Step 2). 
Note:
	•	 If the camera is used in near-horizontal position, the shadow of the dome cover may appear in  
the image. 
1  Loosen  the  zoom  knob  and  focus  knob.  Select  photographic  subject  and  choose  proper  view 
angle through zooming. Adjust the zoom and focus rings to make the image clear (approximate  
adjustment). 
Note:
	•  The  focus  may  not  be  adjusted...