Panasonic Color CCTV Camera Wv Cf624 Wv Cf634 Installation Guide

							21
•	Subject	with	large	illuminance	change	 
•	Subject	with	low	illuminance	 
•	Too	bright	or	reflective	subject	 
•	Subject	through	a	window	 
•	Place	where	the	lens	easily	becomes	dirty	 
•	Subject	with	less	contrast	such	as	white	wall	 
•	Subject	with	remarkable	depth	 
•	Subject	with	heavy	flicker	 
•	Subject	with	horizontally	parallel	lines	such	as	a	shutter

1 Loosen the zoom knob and adjust to the best view angle between TELE and WIDE.
Note:
 •	The	focus	may	not	be	adjusted	smoothly	when	the	zoom	adjustment	ring	is	extremely	close	to	
the  end  of  W  direction  (T  direction).  At  this  time,  slightly  adjust  the  zoom  adjustment  ring  
towards the T direction (W direction), and then adjust the focus. 
2 Tighten the zoom knob. 
3 Rotate the front of the lens, and make coarse adjustment of the focus between NEAR and FAR. 
4 Press the [AF] button on the side of the camera, which will automatically focus. 
Note:
 •	 The	AF	function	is	not	available	over	the	entire	focus	range.	Be	sure	to	perform	approximate	
adjustment of the view angle before manual focusing, and then press the [AF] button to enable  
the AF function. 
•	 For	the	following	subjects,	select	ELC	control	method,	and	then	manually	adjust	the	focus.	
•	Fast-moving	subject	
•	Subject	with	significant	illuminance	change
•	Subject	with	low	illuminance	(such	as	high	beam	light)	
•	Too	bright	or	reflective	subject	
•	Subject	behind	a	window	
•	Less	contrasty	subject	(such	as	white	wall)	
•	Subject	with	remarkable	depth	
•	Subject	with	flicker
•	Subject	with	parallel	lines	(such	as	a	shutter)	
•	Blurred	or	dirty	spherical	cover	 
						

							22
Attaching the dome cover
1  Align the mark with [|] on the dome cover, 
and then install the dome cover. 
Mark
Mark [|] 
2 Adjust the orientation of the dome cover. 
Turn	the	enclosure	clockwise	so	that	the	
mark	aligns	with	[||].	 
Turn  the  dome  cover  to  the  left  or  right 
while viewing the monitor so that the light is 
not	blocked.	
Important: 
•	 Be	sure	to	align	the	mark	with	[||]	when	
adjusting the dome cover. Do not apply 
excessive force, or you may cause  
damage.
3  Turn the dome cover clockwise so that 
the mark aligns with [|||].
Mark
Mark 
						

							23
AF button
4  Fix the dome cover and camera body with  
the dome cover fixing screw (M3).
(Recommended torque: 0.59 N·m  
{0.43 lbf·ft}) 
5  After finishing the installation,  
completely peel off the protection sheet  
that had been retained on the camera. 
6  Press  the  [AF]  button  again  to  adjust 
the focus. CF634 
For more information, refer to page 21.
Dome coverxing 
screw (M3) 
						

							24
Setup menu
Performing each setting item in the setup menu should be completed in advance to use this unit. Perform  the  settings  for  each  item  in  accordance  with  the  conditions  of  the  camera  shooting area.
List of setup menu
Setup itemDescription
CAMERA ID This item specifies the camera title. The camera title that indicates the camera loca-tion and other information about the camera is created with alphanumeric characters  and symbol, and then displayed on the screen. 
CAMERAPerforms the camera operation settings. 
SCENE 1/SCENE 2 Selects  a  scene  file.  It  is  possible  to  register  and  save  the  settings  as  a  scene  file  in case that it is necessary to change the settings such when shooting at night. 
ALC/ELCSelects the method of controlling the quantity of light in accordance with the lens to be used. 
SHUTTER Specifies the electronic shutter speed. 
AGC Specifies gain adjustment. 
SENS UP Specifies electronic sensitivity enhancement. 
WHITE BAL Specifies white balance adjustment. 
DNR Selects the level of the digital noise reduction function.
D&N(ELE)Performs	each	setting	regarding	the	black-and-white	mode	such	as	switching	between	color	and	black-and-white	images.
VMDPerforms settings regarding VMD (Video Motion Detection)
SYSTEM Performs	the	settings	regarding	the	camera	system	such	as	synchronization	and	pri-vacy	zone.	
SYNC Specifies	the	synchronization	type.
PRIVACY ZONE Hides undesired portions in the camera shooting area. 
STABILIZER Decides	whether	or	not	to	enable	the	image	stabilizer.	
EL-ZOOM Switches	the	electronic	zoom	on	and	off.	
UPSIDE-DOWNFlips	the	camera	images	vertically	or	horizontally.	
LDCAdjusts  the  lens  distortion  correction  to  convert  the  image  so  that  it  matches  the square monitor. 
BACK-FOCUS CF634 Selects	the	adjustment	method	and	fine	adjustment	method	for	back	focus.	
SPECIAL 
CHROMA GAINAdjusts the chroma level (color density). 
AP GAINAdjusts the aperture level. 
PEDESTAL Adjusts the pedestal (brightness) level.  
HUEAdjusts the chroma phase (hue).
DISPLAYPerforms the image display setting.
PIX OFF Corrects image defects such as flaws. 
CAMERARESET Restores the settings in the setup menu to the default settings.
SER.NO.Displays the serial number of this product.  
LANGUAGESelects a language to be used in the setup menu. 
						

							25
Screenshot 2
The  setup  mode  changes  to  "ENABLE",  and  
the setup menu becomes ready to be set. 
Step 3
Move  the  cursor  to  the  item  to  be  set,  and 
press the [SET ] button. 
Screenshot 1
Hold  down  the  [SET]  button  for  about  2  sec-
onds  to  call  up  the  top  screen  of  the  setup 
menu. 
Step 1
Press the [UP] button or the [DOWN] button to  
move the cursor to "END".
Step 2
Press  the  [RIGHT]  button  to  move  the  cursor 
to  "SETUP",  and  press  the  [SET ]  button  to  
change  the  setup  mode  from  "DISABLE"  to 
"ENABLE". 
 MODEL   WV-CF634 CAMERA ID     OFF CAMERA   SYSTEM 
SPECIALBACK-FOCUS 
LANGUAGE 
 END   SETUP DISABIE
 MODEL   WV-CF634CAMERA ID     OFF CAMERA   SYSTEM BACK-FOCUS SPECIALLANGUAGE 
 END   SETUP ENABLE
The  operations  in  the  setup  menu  are  performed  with  the  operation  buttons  after  calling  up  the  
setup menu on the connected video monitor. 
The description below explains how to operate the setup menu basically. 
Screenshots of WV-CF634 are shown as an example. 
     
Basic operation 
						

							26
Screenshot 3
The  selected  setup  screen  in  the  setup  menu  
appears on the screen. 
Note: 
	 •	 If	the	top	screen	of	the	setup	menu	is	
called  up  with  the  operation  buttons,  the  
s e t u p   m o d e   i s   a l w a y s   " D I S A B L E "   t o 
prevent operation errors. 
   To  perform  settings  in  the  setup  menu, 
change the setup mode to "ENABLE". 
	 •	 The	cursor	is	a	reversely	highlighted	part.	 
     
Step 4
Perform the settings for each item.
•	Selection of setting item:
Press the [UP] button or [DOWN] button to  
move the cursor.
•	Change	of	settings:
Press the [RIGHT] button or [LEFT] button.
•	Display	of	advanced	setup	screen:
P r e s s   t h e   [ S E T ]   b u t t o n   w h e n   ""   i s 
attached to the target setting item.
•	Return	to	previous	setup	screen:
Move  the  cursor  to  "RET"  and  press  the 
[SET] button.
•	Return	to	the	top	screen:
Move  the  cursor  to  "TOP"  and  press  the 
[SET]  button,  to  display  the  top  screen  of 
the setup menu.
Step 5
Move the cursor to “END” and press the [SET]
button to return to the camera image screen,
or wait about 5 minutes and the setup menu
will automatically close.
    **CAMERA SETUP** SCENE1  ALC/ELC     ALC     SHUTTER     OFF AGC         ON(HIGH) SENS UP     OFF WHITE BAL   ATW1 DNR         HIGH      AUTO1      OFF VMD 
 RET TOP END
D&N(IR) 
						

							
27
Screen transition diagram CF634 
Top screenCAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
SPECIAL  SETUP screen
LANGUAGE SETUP screen 
 MODEL   WV-CF634
CAMERA ID     OFF
CAMERA    
SYSTEM
BACK-FOCUS
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
     **CAMERA ID**   
 
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +- */%$
    SPACE POSI
    RET TOP END RESET
    ................
    **SYSTEM SETUP** 
PRIVACY ZONE  OFF SYNC          INT
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN      OFF
  -     +
LDC           I......  
0
 RET TOP END
BACK-FOCUS SETUP screen
    **BACK-FOCUS SETUP**  MANUAL-ADJ     
ABF           PUSH SET
C/L  B/W      FI
X
 
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        .. .
I ... 20
PEDESTAL       . .
.
I ... 15
HUE           ...I...   0
DISPLAY       ALARM               -      +
PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX
 RET TOP END
    **CAMERA SETUP** 
SCENE1
 ALC/ELC     ALC     
 SHUTTER     OFF
 AGC         ON(HIGH)
 SENS UP     OFF
 WHITE BAL   ATW1
 DNR         HIGH       AUTO1
 VMD
 RET TOP END
D&N(IR )
OFF 
						

							28
Top screenCAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
SPECIAL SETUP screen
LANGUAGE SETUP screen 
 MODEL   WV-CF624 CAMERA ID     OFFCAMERA   SYSTEM SPECIAL LANGUAGE 
  
 END   SETUP DISABLE
   **LANGUAGE SETUP** 
LANGUAGE      ENGLISH 
 SET  RET TOP END
     **CAMERA ID**         0123456789     ABCDEFGHIJKLM     NOPQRSTUVWXYZ     ().,:;&#!?=     +-*/%$
    SPACE POSI    RET TOP END RESET 
    ................
    **SYSTEM SETUP** 
PRIVACY ZONE  OFF 
SYNC          INT 
STABILIZER    OFF EL-ZOOM       OFF UPSIDE-DOWN    OFF
 -     +LDC           I......  0
 RET TOP END
   **SPECIAL SETUP** CHROMA GAIN   ....I..160AP GAIN       ..I.... 20PEDESTAL      . ..I... 15HUE           ...I...  0 
DISPLAY       ALARM               -     + 
PIX OFF CAMERA RESET  PUSH SET  SER.NO. XXXXXXXX  RET TOP END
    **CAMERA SETUP**  SCENE1 ALC/ELC     ALC     SHUTTER     OFF AGC         ON(HIGH) SENS UP     OFF WHITE BAL   ATW1 DNR         HIGH      AUTO1 VMD 
 RET TOP END
D&N(IR)OFF
Screen transition diagram CF624
 
						

							29
Blurred image
No image displayed
Cause/solutionReference page Symptom 
Troubleshooting 
Before asking for repairs, confirm the causes with the following table.  
Contact your dealer if a problem cannot be solved even after checking and trying the solution in 
the table or a problem is not described below. 
–
20-21
–
–
–
15-16
18
	•	 Are	the	power	cord	and	coaxial	cable	connected appropriately? →	 Check	whether	the	connection	is	appropriately established.
	•	 Is	the	adjustment	monitor	connected?	 → Confirm whether the monitor is con-nected.
	•	 Is	the	monitor	brightness	appropriately	adjusted, or is the contrast appropriately  adjusted?  →	Check	whether	the	monitor	settings	are	appropriate.
	•	 Is	the	cushioning	material	in	the	spherical	cover removed?  → Confirm whether the cushioning material has been removed. 
–	•	 Is	the	spherical	cover	dirty	or	damaged?	 → Verify the state of the spherical cover. 
	•	 Is	the	focus	adjusted	correctly?			 → Check	if	the	focus	is	adjusted	correctly.	
	•	 Is	the	lens	of	the	camera	soiled	with	dirt	or	dust? → Check	whether	the	lens	of	the	camera	is	clean.  
	•	 The	power	cord	or	connector	is	damaged.	Continuous use of the damaged cord or  connector	may	cause	electric	shock	or	fire.    Turn off the power supply immediately and request repair from your dealer. The temperature of power 
cord rises or falls when the  
power cord is bent or 
stretched during use 
Damaged power cord 
sheathing
Heated portion of power line  consisting of power cord and connector during use 
						

							30
Specifications 
WV-CF634WV-CF624
Power source 24	V	AC	60	Hz,	12	V	DC	
Power consumption24 V AC: 2.5 W, 12 V DC: 220 mA 
Image sensor 1/3-type interline transfer CCD
Effective pixels 976 (H)×494 (V) 
Scanning area 4.8 mm (H)×3.6 mm (V) {3/16 inches (H)×5/32 inches (V)}
Scanning system2:1 interlace
Scanning line525 lines
Horizontal	scanning	frequency15.734	kHz
Vertical scanning frequency59.94	Hz
SynchronizationInternal (INT) , Multiplexed vertical drive(VD2)
Horizontal	resolution650 TV lines 
Vertical resolution350 TV lines
Video output1.0 V [p-p] NTSC composite video signal 75 Ω
Signal-to-noise ratio52 dB (AGC OFF)
Dynamic range52 dB typ. (Super Dynamic 6 ON)
Minimum illumination0.08 lx {0.008 footcandle} (color mode) 
0.008	lx	{0.0008	footcandle}	(black-and-white	mode)
Lens 3.6x vari-focal lens
Focal length2.8 mm to 10.0 mm {5/16 inches-13/32 inches}
Aperture ratioF1.3 (WIDE)  to F3.1 (TELE)
View angleWIDE (H×V) 100.8°×73.8° TELE (H×V) 27.6°×20.7°
Adjustable angle range Pan: –170° to +180°Tilt:±90 °Azimuth:±100	° 
Ambient operating temperature –10 °C to +50 °C {14°F to 122°F}
Ambient operating humidityLess than 90 %
Dimensions108 mm  (D) × 94 mm (H) {4-1/4 inches (D) x 3-23/32 inches (H)}
Mass320 g {0.71lbs}
Camera title English letter, numbers and symbols: up to 16 characters. 
Light control mode settingALC/ALC+/ELC
Super dynamicON/OFF
Shutter speed OFF (1/60), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/120000 (s)
Auto gain controlON (HIGH, MID, LOW)/OFF
Sensitivity upOFF/AUTO (×2, ×4, ×6, ×10, ×16, ×32) /FIX (×2, ×4, ×6, ×10, ×16, ×32, ×64, ×128, ×256, ×512) 
White balanceATW1/ATW2/AWC
Digital noise reductionLOW/HIGH