Panasonic Color CCTV Camera Wv Cf304 Wv Cf314 Installation Guide

21
1 Loosen the zoom knob and adjust to the best view angle between TELE and\
 WIDE.
Note:
 • The focus may not be adjusted smoothly when the zoom adjustment ring is extremely close to the end of W direction (T direction). At this time, slightly adjust the zoom adjustment ring 
towards the T direction (W direction), and then adjust the focus. 
2 Tighten the zoom knob. 
3 Rotate the front of the lens, and make coarse adjustment of the focus between NEAR an\
d FAR.
4 Press the [AF] button on the side of...

22
Attaching the dome cover
1 Align the mark with [|] on the dome cover, 
and then install the dome cover. 
3  Fix the dome cover and camera body 
with the dome cover fixing screw (M3).
(Recommended torque: 0.59 N·m {0.44 lbf·ft}) 
4  After finishing the installation, 
completely peel off the protection sheet 
that had been retained on the camera. 
5  Press the [AF] button again to adjust 
the focus. 
CF314L
For more information, refer to page 21.
Mark
Mark [I]
2  Turn the dome cover clockwise so that...

23
Setup menu
Performing each setting item in the setup menu should be completed in ad\
vance to use this unit.
Perform the settings for each item in accordance with the conditions of the camera shooting area.
List of setup menu
Setup itemDescription
CAMERA ID
 This item specifies the camera title. The camera title that indicates th\
e camera 
location and other information about the camera is created with alphanumeric 
characters and symbol, and then displayed on the screen. 
CAMERA Performs the camera...

24
Screenshot 2
The setup mode changes to "ENABLE", and 
the setup menu becomes ready to be set. Step 3
Move the cursor to the item to be set, and 
press the [SET ] button. 
Screenshot 1
Hold down the [SET] button for about 2 sec-
onds to call up the top screen of the setup 
menu. Step 1
Press the [UP] or [DOWN] button to move the 
cursor to "END".
Step 2
Press the [RIGHT ] button to move the cursor 
to "SETUP", and press the [SET ] button to 
change the setup mode from...

25
Screenshot 3
The selected setup screen in the setup menu 
appears on the screen. 
 
Note: • If the top scr een of the setup menu is 
called up with the operation buttons, the 
setup mode is always "DISABLE" to 
prevent operation errors.
   To perform settings in the setup menu, 
change the setup mode to "ENABLE". 
 • The cursor is a r eversely highlighted part.
    
Step 4
Perform the settings for each item. 
 • Selection of setting item: 
   Press the [UP] or [DOWN] button to move...

26
Screen transition diagram CF314L
Top screen CAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
BACK-FOCUS SETUP screen
 MODEL   WV-CF314L
CAMERA ID     OFF
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE     **CAMERA ID**    
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +- */%$
    SPACE POSI
    RET TOP END RESET
    ................
    **SYSTEM SETUP** 
PRIVACY ZONE  OFF SYNC          INT
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN    OFF
  -     +...

27
Screen transition diagram CF304L
Top screen CAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
 MODEL   WV-CF304L
CAMERA ID     OFF
CAMERA   
SYSTEM
 
 END   SETUP DISABLE
SPECIAL
LANGUAGE
     **CAMERA ID**    
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +- */%$
    SPACE POSI
    RET TOP END RESET
    ................
    **SYSTEM SETUP**  SYNC          INT
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN    OFF
LDC           ....I..160
 RET TOP...

28
Blurred image
The temperature of power cord rises or falls when the 
power cord is bent or 
stretched during use 
Damaged power cord sheathing
No image displayed
Cause/solutionReference page Symptom 
Troubleshooting 
Before asking for repairs, confirm the causes with the following table. 
Contact your dealer if a problem cannot be solved even after checking and trying the solution in th\
e 
table or a problem is not described below. 
–
–
20-22
–
–
16-17
19
	•	 Are	the	power	cord	and	coaxial	cable...

29
Specifications 
WV-CF314LEWV-CF304LE
Power source  24 V AC 50/60 Hz, 12 V DC
Power consumption 24 V AC: 3.6 W, 12 V DC: 410 mA IR LED on 
Image sensor  1/3-type interline transfer CCD
Effective pixels  976 (H)×582 (V)
Scanning area  4.8 mm (H)×3.6 mm (V)
Scanning system 2:1 interlace
Scanning line 625 lines
Horizontal scanning frequency15.625 kHz
Vertical scanning frequency50.00 Hz
Synchronization Internal (INT) (Multiplexed vertical drive (VD2) cannot  be set)
Horizontal resolution 650 TV lines...

30
CD-ROM* ............................................................1 pc.
Installation Guide(this book)
 .................................1 pc.
*The CD-ROM contains the operating installations and installation guide \
(PDF).
The following is used during installation procedures: 
Installation template label
 .....................................1 pc. 
Standard accessories 
   Values of mass and dimensions are approximate. The specification is subject to change without 
notice. 
WV-CF314LEWV-CF304LE...