Panasonic Color CCTV Camera Wv Cf304 Wv Cf314 Installation Guide

							21
1 Loosen the zoom knob and adjust to the best view angle between TELE and\
 WIDE.
Note:
 • The focus may not be adjusted smoothly when the zoom adjustment ring is extremely close to the end of W direction (T direction). At this time, slightly adjust the zoom adjustment ring 
towards the T direction (W direction), and then adjust the focus. 
2 Tighten the zoom knob. 
3 Rotate the front of the lens, and make coarse adjustment of the focus between NEAR an\
d FAR.
4 Press the [AF] button on the side of the camera, and the ABF function will automatica\
lly 
focus.
Note:
 • The ABF function is not available over the entir e focus range. Be sure to perform approximate 
adjustment of the view angle before manual focusing, and then press the [AF] button to enable 
the ABF function. 
• For the following subjects, select ELC control method, and then manually adjust the focus. 
• Fast-moving subject 
• Subject with significant illuminance change
• Subject with low illuminance (such as high beam light) 
• Too bright or reflective subject 
• Subject behind a window 
• Less contrasty subject (such as white wall) 
• Subject with remarkable depth 
• Subject with flicker
• Subject with parallel lines (such as a shutter) 
• Blurred or dirty spherical cover 
Rotation angle: 
+120 ° 
NEAR
WIDE FA R
TELE
Zoom knob Focus knob 
 
						

							22
Attaching the dome cover
1 Align the mark with [|] on the dome cover, 
and then install the dome cover. 
3  Fix the dome cover and camera body 
with the dome cover fixing screw (M3).
(Recommended torque: 0.59 N·m {0.44 lbf·ft}) 
4  After finishing the installation, 
completely peel off the protection sheet 
that had been retained on the camera. 
5  Press the [AF] button again to adjust 
the focus. 
CF314L
For more information, refer to page 21.
Mark
Mark [I]
2  Turn the dome cover clockwise so that 
the mark aligns with [||].
Mark [II]
Dome cover fixing 
screw (M3)
AF button  
						

							23
Setup menu
Performing each setting item in the setup menu should be completed in ad\
vance to use this unit.
Perform the settings for each item in accordance with the conditions of the camera shooting area.
List of setup menu
Setup itemDescription
CAMERA ID
 This item specifies the camera title. The camera title that indicates th\
e camera 
location and other information about the camera is created with alphanumeric 
characters and symbol, and then displayed on the screen. 
CAMERA Performs the camera operation settings. 
SCENE 1/
SCENE 2  Selects a scene file.  It is possible to register and save the settings as a scene file in 
case that it is necessary to change the settings such when shooting at n\
ight. 
ALC/ELC Selects the method of controlling the quantity of light in accordance with the lens to 
be used. 
SHUTTER  Specifies the electronic shutter speed. 
AGC  Specifies gain adjustment. 
SENS UP  Specifies electronic sensitivity enhancement. 
WHITE BAL  Specifies white balance adjustment. 
DNR  Selects the level of the digital noise reduction function.
D&N
(IR) Performs each setting regarding the black-and-white mode such as switching 
between color and black-and-white images.
VMD Performs settings regarding VMD (Video Motion Detection)
SYSTEM
 Performs the settings regarding the camera system such as synchronization and pri -
vacy zone. 
SYNC  Only INT method can be used; VD2 synchronization cannot be used. 
PRIVACY ZONE  Hides undesired portions in the camera shooting area. 
STABILIZER  Decides whether or not to enable the image stabilizer. 
EL-ZOOM  Switches the electronic zoom on and off. 
UPSIDE-DOWN Flips the camera images vertically or horizontally. 
LDC Adjusts the lens distortion correction to convert the image so that it matches the 
square monitor. 
BACK-FOCUS CF314LSelects the adjustment method and fine adjustment method for back focus.\
 
SPECIAL 
CHROMA GAIN Adjusts the chroma level (color density). 
AP GAIN Adjusts the aperture level. 
PEDESTAL  Adjusts the pedestal (brightness) level.  
PIX OFF  Corrects image defects such as flaws. 
CAMERA
RESET  Restores the settings in the setup menu to the default settings.
SER.NO. Displays the serial number of this product.  
LANGUAGE Selects a language to be used in the setup menu.  
						

							24
Screenshot 2
The setup mode changes to "ENABLE", and 
the setup menu becomes ready to be set. Step 3
Move the cursor to the item to be set, and 
press the [SET ] button. 
Screenshot 1
Hold down the [SET] button for about 2 sec-
onds to call up the top screen of the setup 
menu. Step 1
Press the [UP] or [DOWN] button to move the 
cursor to "END".
Step 2
Press the [RIGHT ] button to move the cursor 
to "SETUP", and press the [SET ] button to 
change the setup mode from "DISABLE" to 
"ENABLE". 
 MODEL   WV-CF314L
CAMERA ID     OFF
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 END   SETUP DISABIE
BACK-FOCUS
 MODEL   WV-CF314L
CAMERA ID     OFF
CAMERA   
SYSTEM
 END   SETUP ENABLE
SPECIAL
LANGUAGEBACK-FOCUS
The operations in the setup menu are performed with the operation buttons after calling up the 
setup menu on the connected video monitor. 
The description below explains how to operate the setup menu basically. 
Screenshots of WV-CF314LE are shown as an example. 
    
Basic operation 
						

							25
Screenshot 3
The selected setup screen in the setup menu 
appears on the screen. 
 
Note: • If the top scr een of the setup menu is 
called up with the operation buttons, the 
setup mode is always "DISABLE" to 
prevent operation errors.
   To perform settings in the setup menu, 
change the setup mode to "ENABLE". 
 • The cursor is a r eversely highlighted part.
    
Step 4
Perform the settings for each item. 
 • Selection of setting item: 
   Press the [UP] or [DOWN] button to move 
the cursor. 
 •  Change of settings: 
   Press the [RIGHT ] or [LEFT ] button. 
 • Display of advanced setup screen: 
   Press the [SET ] button when "" is 
attached to the target setting item. 
	 •	
Return to previous setup screen: 
   Move the cursor to "RET" and pr ess the 
[SET ] button. 
	 •	Return to the top screen:
   Move the cursor to "TOP" and pr ess the 
[SET ] button, to display the top screen 
of the setup me
nu. 
Step 5
Move the cursor to “END” and press the [SET ] 
button to return to the camera image screen, 
or wait about 5 minutes and the setup menu 
will automatically close. 
    **CAMERA SETUP**  SCENE1
 ALC/ELC     ALC    
 SHUTTER     OFF
 AGC         ON(LOW)
 SENS UP     OFF
 WHITE BAL   ATW1
 DNR         HIGH
 VMD         OFF
 RET TOP END
D&N(IR)     AUTO2 
						

							26
Screen transition diagram CF314L
Top screen CAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
BACK-FOCUS SETUP screen
 MODEL   WV-CF314L
CAMERA ID     OFF
CAMERA   
SYSTEM
SPECIAL
LANGUAGE
 
 END   SETUP DISABLE     **CAMERA ID**    
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +- */%$
    SPACE POSI
    RET TOP END RESET
    ................
    **SYSTEM SETUP** 
PRIVACY ZONE  OFF SYNC          INT
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN    OFF
  -     +
LDC           I......  0
 RET TOP END
   **BACK-FOCUS SETUP** ABF            PUSH SET   
MANUAL-ADJ     
C/L  B/W       FIX
 RET TOP END
SPECIAL SETUP screen
LANGUAGE SETUP screen 
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ...I.... 32
PEDESTAL       . .
.
I ... 16
              -     +
PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX
 RET TOP END
    **CAMERA SETUP** 
SCENE1
 ALC/ELC     ALC    
 SHUTTER     OFF
 AGC         ON(LOW)
 SENS UP     OFF
 WHITE BAL   ATW1
 DNR         HIGH       AUTO2
 VMD
 RET TOP END
D&N(IR)
OFF
BACK-FOCUS 
						

							27
Screen transition diagram CF304L
Top screen CAMERA ID screen
CAMERA SETUP screen
SYSTEM SETUP screen
 MODEL   WV-CF304L
CAMERA ID     OFF
CAMERA   
SYSTEM
 
 END   SETUP DISABLE
SPECIAL
LANGUAGE
     **CAMERA ID**    
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +- */%$
    SPACE POSI
    RET TOP END RESET
    ................
    **SYSTEM SETUP**  SYNC          INT
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN    OFF
LDC           ....I..160
 RET TOP END
SPECIAL SETUP screen
LANGUAGE SETUP screen 
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ...I.... 32
PEDESTAL       . .
.
I ... 16
              -     +
PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX
 RET TOP END
    **CAMERA SETUP** 
SCENE1
 ALC/ELC     ELC    
 SHUTTER     ---
 AGC         ON(LOW)
 SENS UP     OFF
 WHITE BAL   ATW1
 DNR         HIGH       AUTO2
 VMD
 RET TOP END
D&N(IR)
OFF
  -     + 
						

							28
Blurred image
The temperature of power cord rises or falls when the 
power cord is bent or 
stretched during use 
Damaged power cord sheathing
No image displayed
Cause/solutionReference page Symptom 
Troubleshooting 
Before asking for repairs, confirm the causes with the following table. 
Contact your dealer if a problem cannot be solved even after checking and trying the solution in th\
e 
table or a problem is not described below. 
–
–
20-22
–
–
16-17
19
	•	 Are	the	power	cord	and	coaxial	cable	connected appropriately? → Check whether the connection is appropriately established.
	•	 Is	the	adjustment	monitor	connected?	 → Confirm whether the monitor is con-nected.
	•	 Is	the	cushioning	material	in	the	spherical	cover removed?  → Confirm whether the cushioning material has been removed. 
	•	 Is	the	spherical	cover	dirty	or	damaged?	 → Ve r ify the state of the spherical cover. 
	•	 Is	the	focus	adjusted	correctly?			 → Check	if	the	focus	is	adjusted	correctly.	
	•	 Is	the	lens	of	the	camera	soiled	with	dirt	or	dust? → Check whether the lens of the camera is 
clean.  
	•	 The	power	cord	or	connector	is	damaged.	Continuous use of the damaged cord or 
connector may cause electric shock or 
fire. 
   Turn off the power supply immediately and request repair from your dealer. 
Heated portion of power line 
consisting of power cord and 
connector during use
–
	•	 Is	the	connected	system	controller	set	to	multiplexed	vertical	drive	(VD2)? → Check whether the connected system controller is set correctly.Black line in image 
						

							29
Specifications 
WV-CF314LEWV-CF304LE
Power source  24 V AC 50/60 Hz, 12 V DC
Power consumption 24 V AC: 3.6 W, 12 V DC: 410 mA IR LED on 
Image sensor  1/3-type interline transfer CCD
Effective pixels  976 (H)×582 (V)
Scanning area  4.8 mm (H)×3.6 mm (V)
Scanning system 2:1 interlace
Scanning line 625 lines
Horizontal scanning frequency15.625 kHz
Vertical scanning frequency50.00 Hz
Synchronization Internal (INT) (Multiplexed vertical drive (VD2) cannot  be set)
Horizontal resolution 650 TV lines 
Vertical resolution 400 TV lines
Video output 1.0 V [p-p] PAL composite video signal 75 
Signal-to-noise ratio52 dB (AGC OFF)
Minimum illumination 0.08 lx (color mode)
0.15 lx (color mode)
0.008 lx (black-and-white mode•IR LED off) 0.015 lx (black-and-white mode•IR LED off)
0 lx (black-and-white mode•IR LED on)
0 lx (black-and-white mode•IR LED on)
Lens 3.6x vari-focal lens Fixed-focal lens
Focal length 2.8 mm to 10.0 mm 2.8 mm
Aperture ratio F1.3 (WIDE) to F3.1 (TELE) F2.0
View angle Horizontal: 100°50' (WIDE)  
to 27°39' (TELE) 
Vertical: 73°51' (WIDE)  
to 20°45' (TELE) Horizontal: 101°30' 
Vertical: 75°
Adjustable angle range  Pan: –170 
° to +180 
° 
Tilt: 0 to 75 ° 
Azimuth: -100 ° to +100 °   Azimuth: -120 ° to +120 ° 
Ambient operating temperature –10 
°C to +50 
°C
Ambient operating humidityLess than 90 %
Dimensions ø123 mm × 106 mm (H)
Mass Approx. 390 g Approx. 330 g
Camera title  English letter, numbers and symbols: up to 16 characters. 
Light control mode setting ALC/ALC+/ELC ELC
Back light compensation (BLC)ON/OFF
Adaptive black stretch (ABS)ON/OFF
Shutter speed  OFF (1/50), 1/120, 1/250, 1/500, 1/1000, 
1/2000, 1/4000, 1/10000, 1/120000 
(s)---
Auto gain control ON (HIGH, MID, LOW)/OFF
Sensitivity up OFF/AUTO (×2, ×4, ×6, ×10, ×16, 
×32) /FIX (×2, ×4, ×6, ×10, ×16, 
×32, ×64, ×128, ×256, ×512)  OFF/AUTO (×2, ×4, ×6, ×10, ×16, 
×32)
White balance ATW1/ATW2/AWC
Digital noise reduction LOW/HIGH 
						

							30
CD-ROM* ............................................................1 pc.
Installation Guide(this book)
 .................................1 pc.
*The CD-ROM contains the operating installations and installation guide \
(PDF).
The following is used during installation procedures: 
Installation template label
 .....................................1 pc. 
Standard accessories 
   Values of mass and dimensions are approximate. The specification is subject to change without 
notice. 
WV-CF314LEWV-CF304LE
Day&Night (IR) AUTO1/AUTO2/ON/OFF 
IR LED lights irradiation 
distance 20 m  
10 m 
IR LED lights OFF/AUTO/FIX
Video motion detection OFF/MOTION DETECTION/SCENE CHANGE  
Number of scene file 2
Privacy zone ON (1)/ON (2)/OFF
Image stabilizer  ON/OFF 
Electronic zoom  ON (up to 2x)/OFF
Upside-down ON/OFF
Lens distortion correction 0 to 255
Back-focus setup ABF/MANUAL ---