Panasonic Color CCTV Camera Wv Cf304 Wv Cf314 Installation Guide

11
Locally procure the screws
Screws are not supplied with this product. 
Prepare the screws according to the material, 
structure, strength and other factors of the 
mounting area and the total weight of objects 
to be mounted.
Screw tightening
 • The scr ews and bolts must be tightened 
with an appropriate tightening torque 
according to the material and strength of 
the installation area. 
 • Do not use an impact driver . Failure to 
observe this may cause overtightening and 
consequently damage to...

12
Major operating controls and their functions
1 Video output connector
Transmits composite video signals.
2
 Mark
This mark is used when the dome cover is 
installed.
3
 Lens
4 Panning table lock screw [LOCK]
Locks the panning position after adjustment.
5 Panning table
Adjusts the panning position of the camera.
6
 Tilting lock scr ew 
Fixes the tilting position.  7
 AF button [ABF] CF314L
 page 21.
8
 Setup button [SET]
Hold down the [SET] button for more 
than 2 seconds and the setup menu will 
be...

13
• [SET]: Press this button in the menu to 
confirm the selected value or function. In 
addition, this button is used to open 
submenus. 
9
 Adjustment monitor output jack
Connect the adjustment monitor (small LCD 
monitor, etc.) to the adjustment monitor 
output jack to adjust the camera angle.  
0
 Azimuth adjuster
Adjusts the azimuth angle of the camera.
A
 Zoom knob (with lock function) CF314L
Locks the zoom position after zoom 
adjustment.
B
 Focus knob CF314L
C IR LED 
D LED photoptic
E Tilting...

14
 Remove the dome cover
1 Peel off the protection sheet from the dome 
cover. Don't remove completely as this 
protects the dome during installation. 
2 Loosen the dome cover fixing screw.
3 Adjust the mark on this unit to [|] on the 
dome cover, and turn the dome cover 
counterclockwise to remove it.
When installing the camera on a wall or ceiling, there are two methods as specified below.
	 •	 Use	the	two-gang	junction	box
	 •	 Installing	the	camera	directly	on	a	wall	or	ceiling
Important:
	 •...

15
 About the side cable access hole 
If you choose not to drill hole in the wall or 
ceiling, but to wire the camera with the cable 
exposed, cut the cable access hole on the side 
of the dome cover to provide a cable entry. 
Precautions when wiring from the side: 
• Remove the dust guar d cap. Run the cable 
through the cable access hole and bend it 
inward, then reinstall the dust guard cap. 
• Run the cable through the side cable access 
hole as shown. 
• Be careful not to pinch the cable with the...

16
Installing the camera directly on a wall or ceiling
Affix the installation template label (accessory) to the ceiling or wall\
, and use a pen to mark the 
positions of the screws and cable mounting hole in the ceiling or wall. 
Remove the installation template label, and attach the camera with 4 scr\
ews (M4, locally procured). 
 Connections
Connect the video output
Important: 
	 •	 Be	sure	to	turn	off	the	power	of	each	
device before connecting. 
	 •	 Be	sure	to	secure	the	coaxial	cable...

17
Important:  • The power supply of 24 V AC/12 V DC shall be insulated against  220 to 240 V AC.
 • The power supply is automatically switchover either 24 V AC or  12 V DC. No setting is required 
with this camera. 
Connection of power cord
When connecting the power cord, use connectors that are designed for the power cord, and be 
careful not to let the power cord fall off. 
In addition, waterproofing work is needed at the joint, e.g., wrapping waterproof tape around the 
joint. 
Cable length and wire...

18
Installation of camera 
Turn off the power of all related devices before installation. 
1	 Remove the dome cover.
2 Connect all cables.
3 Install the camera (The illustration below shows installation using a \
gang junction box). Mount the camera with 4 screws (M4, locally procured). 
Important: 
• Be sure to avoid twisting the cables when tightening the screws.
Note:
•  When attached to the ceiling:
Install the camera with the “FRONT ” arrow of the installation mark facing forward.
• When attached to...

19
1 Connect the ∅3.5 mm miniature plug (mono channel) to the adjustment monitor output jack. 
Important:
 
• This video output is intended for confirmation of view angle, e tc. during installation or repair 
service, and not for recording or monitoring. 
Note: 
• Adjustment monitor output jack is prior to video output cable.  Video cannot be output through 
the video output cable after connecting the adjustment monitor.
2 When the camera is installed on the wall, select "ON" for...

20
3  Adjustment of azimuth 
   Adjust the azimuth by rotating the azimuth adjuster. 
Note:
 • CF314L Adjust  azimuth adjuster to make the image in the forward direction.
 • CF304L Adjust azimuth adjuster, refer to the following pictures, to display the image properly  
          rather than upside-down.
(This illustration represents WV-CF304LE.)(This illustration represents WV-CF314LE.)
Rotation angle: 
-100 ° 
Rotation angle: 
+100 ° 
Rotation angle: 
-120 °  Rotation angle: 
+120 ° 
TO
P
On the wall...