Panasonic Coaxial Lan Converter WJ-PR204 WJ-PR201 WJ-PC200 Operating Instructions

1.4  Included ItemsConfirm that the following items are included in the unit’s packaging.
WJ-PR204/WJ-PR204E/WJ-PR201/WJ-PR201E • Operating Instructions (this document) (1 pc.)
• Warranty Card (1 pc.) WJ-PR204, WJ-PR201
• AC adapter (1 pc.)
• AC Cord (1 pc.) WJ-PR204, WJ-PR201
• AC Cord (2 pcs.) *1
 WJ-PR204E, WJ-PR201E
• BNC Connector Cover (4 ch.) (1 pc.) 
• BNC Connector Cover cap (3 pcs.) *2
 
• BNC Connector Cover (1 ch.) (1 pc.) 
• Screw (M2.6  ´ 10 mm {3/8 inches}) (2 pcs. of them, 1 for spare)...

1.5  For Your SafetyTo prevent severe injury and loss of life/property, read this section carefully before using
the unit to ensure proper and safe operation of your unit.
1.5.1  WARNINGConsult an authorized dealer for mounting.
• Experience and knowledge are required to perform mounting of the unit. Incorrect
mounting can cause damage to the unit, fire, electric shock, or injury. Make sure
to consult an authorized dealer for mounting.Stop the operation immediately when something is wrong with this...

Always hold the plug when unplugging the power cord. 
• Otherwise, the cord may be damaged and result in a fire or electric shock.
The exclusively designed mount bracket shall be used. 
•Failure to observe this may cause a drop resulting in injury or accidents. Use the
exclusively designed mount bracket for installation.
The screws and bolts must be tightened to the specified torque.
• Failure to observe this may cause a drop resulting in injury or accidents.Periodic inspections shall be conducted.
•...

Avoid installing this product in the locations where salt damage occurs
or corrosive gas is produced.
• Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product may occur.Do not damage the power cable.  
•Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable.
Do not place heavy objects on it, and keep it away from heat sources. Use of a
damaged power cable may cause electric shock, short circuit, or fire. Consult the
dealer for repair.
Do...

Never touch the power plug with wet hands.  
• This may result in electric shock.
Do not pour or wet the unit.
• This may result electric shock or fire. Turn the power off immediately and contact
qualified service personnel for service.Do not touch the unit, ethernet cable, coaxial cable, AC cord, or power
plug during thunderstorms.
• This may result in electric shock.Do not touch the core of the coaxial cable.
• This may result in electric shock. A maximum of DC 60 V is applied to the coaxial
cable....

allow the power to be quickly turned off, use a distribution panel with a circuit
breaker capable of disconnecting the power, or connect this unit to a power
source controller.
5. Handle this product with care. • Do not drop this product, nor apply shock or vibration to the product. Failure toobserve this may cause trouble.
6. Power cable 
 
• The attached AC adapter is designed exclusively for this unit. Do not use it for other devices. In addition, do not use other AC adapters for this unit.
7....

1.7  Precautions for InstallationInstall the unit in accordance with electrical equipment technical standards.
Before beginning to install and connect the unit, check and prepare all necessary
peripheral equipment and cables. Turn off the power supply of the unit, camera, and
other components before connecting them.
All electrical wiring should be performed by a qualified electrician.
Consult an authorized dealer for installation.
Power supply
This product has no power switch. When turning off the power,...

4. Precautions before receiver installations  
•When mounting 3 to 4 connected receiver side units to the rack, use the following
bracket (locally procured).
– Rack mount bracket: For WJ-PR204/WJ-PR201: BY-HCA10A
For WJ-PR204E/WJ-PR201E: BY-HCA10CE
• Available racks – EIA standard rack or equivalent (third party)EIA19 type
• Rack mounting screws
– M5  ´ 12 mm {15/32 inches} screws
5. Precautions before camera installations 
• Use the screws with the specifications shown on page 25 when mounting the...

6. Screw tightening• The screws and bolts must be tightened with an appropriate tightening torqueaccording to the material and strength of the installation area.
• Do not use an impact driver. Use of an impact driver may damage the screws or
cause tightening excessively.
• When a screw is tightened, make the screw at a right angle to the surface. After
tightening the screws or bolts, perform checks to ensure that the tightening is
sufficient enough so that there is no movement or looseness.
7. Coaxial...

8. Mounting and connections• Do not mount camera side units above or below other camera side units. Thiscan cause transmission interference. When mounting several camera side units
in the same area, mount them side by side each other.
• When connecting the coaxial cable to the unit, make sure that no other devices are connected to the coaxial cable. Connecting the coaxial cable to the unit when
there are other devices connected (such as an analog CCTV camera), may
cause damage to the connected device.
•...