Panasonic Cf30 Service Manual

							9-29
9.2.16. Setting the KB Cable Cover, Keyboard and LCD Cable Cover
1. Set the Keyboard onto the Computer.
2. Connect the 2 Cables to the 2 Cables. (CN13,CN14)
3. Fix the KB Cable Cover using the 7 Screws.  No1 to
No7
4. Set the LCD Cable Plate.
5. Fix the LCD Cable Cover using the 3 Screws.  No1 to No3
Note: Tighten the Screws in the numbered order (No1 to No7).
Tighten the Screws in the numbered order (No1 to No3).
Screws : DRQT26+D3FKL
Q  Arranging the Keyboard
 







 to Connector
   (CN14)
Connector
  (CN13)Connector
  (CN14)
 to Connector
   (CN13)
KB Cable Cover
LCD 
Cable Cover
LCD 
Cable Plate
Keyboard
No.6 No.4
No.1 No.5
No.3
No.7
No.2
No.1
No.2
No.3
Attach the Keyboard 
Spacer Tape
Attach the Keyboard 
Spacer Sheet Attach the Keyboard 
Back Plate
Keyboard US is installed
Attach the Keyboard Fook Spacer Lower
Plate hole
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
1. Attach the Keyboard US and Keyboard Spacer. (KB Preparation)
2. Attach the Keyboard Back Plate and Keyboard Spacer Sheet. (Plate Prepar\
ation) (Ensure Keyboard Spacer Sheet does not run over the level of Keyboard B\
ack Plate.)
3. Attach the prepared KB to the prepared plate. (Insert the KB protrusions into the plate holes and determine the posit\
ion.)
: Fit to the edge of plate (KBD back plate).Both sides should not come over the plate. 
						

							9-30
7.2.17. Setting the KB Cover, Hinge Cover L, Hinge Cover R and Keyboard
1. Insert the front hooks of the Keyboard to the Top Cabinet inorder, and set the Keyboard.
2. Fix the Hinge Cover L and R using the 4 Screws  No1 to No3
3. Fix the Hinge Cover L and R using the 2 Screws.  No1, No2
4. Fix the Bluetooth PCB using the Screw. 
5.  Fix the KB  Co ver using the 4  Screws.    No1 to No4
Note: Tighten the Screws in the numbered order (No1 to No4).
Tighten the Screws in the numbered order (No1 to No3).
Tighten the Screws in the numbered order (No1, No2).
Screws : DRHM5054XA
Screws : DRQT26+D4FKL
7.2.18. Setting the HDD
1. Set the HDD FPC to HDD.
2. Attach the Heater to HDD.
3. Attach the Heater Sheet to the Heater.
4. Attach the 2 Sheets to HDD.
5. Attach the 6 HDD Forming MFYPC and the two HDD  Terminal Plate Upper to the HDD Damper Assy.
6. Attach the six HDD Forming MFYPC and the two HDD 
Terminal Plate Upper to the HDD Damper Assy.
7. Set the HDD Damper Assy to HDD.
8. Attach the Side Cushion to the HDD L Case Assy.
9. Set the HDD U Case Assy and the HDD L Case Assy, and set the two Tabs of the HDD L Case Assy.
10. Fix the HDD U Case Assy and the HDD L Case Assy using the 4 Screws  and Screw .
Screws : DFHE5025XA
Screws : DRQT2+E8FKL


 




KB Cover Hinge Cover L
Hinge Cover R
Keyboard
Bluetooth PCBNo.1
No.3
No.2No.4 No.1
No.2No.3
No.1
No.2
HDD U Case Ass’y
HDD FPC
Heater  
HDD L 
Case Ass’y
Ta b Ta b
HDD
HDD 
Damper
Ass’y
Heater Sheet
Sheet
Sheet
 
						

							9-31
Q
 Preparation oh HDD ASSY
0   1
0   1
Attach the HDD Tape S
HDD is setAttach the HDD Tape L
7   1
10    1
20    1
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Fit to the corner.
Turn it to the board side (back side).
1    1
Important Parts 
for Safety
Safety Working Attach the Fuse Sheet Back Side
0    2Attach the Heater Fixed Tape 16    2
Insert the HDD FPC Ass’yConnect the Connector
Heater is set
HDD FPC Ass’y
Valley Fold Mountain Fold1. Do not gouge when inserting and removing the socket.
2. Do not drop HDD or add any impacts on it.
3. Insert CN into the end firmly.
4. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
Check the part number.
Heater
Do not fold because the thermal 
fuse exists in this part.
Lead Wire
HDD FuseDo not bend the bending 
part of Heater
Turn the surplus into the back.
Attach it pushing the shaded 
part not to push the fuse. 
						

							9-32
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
HDD Damper Ass’y
Make sure the product with black 
sheet on the yellow sponge.HDD Set Insert after removing the Release Paper of the two-sided tape.Fold the FPC from the board edge.
HDD Ass’y
Remove the Release Paper on 
the back, close and attach it.
Attach it to HDD closely not to loosen. Push and bend
Longer Direction
(15) (10)
HDD Thermal Plate
1    2
1    2
1    2
0    11    21    2
Attach the HDD Cushion (Yelllow)
Attach the HDD Cushion (Yelllow)
Attach the HDD Cushion 
(Black) Attach the HDD 
Thermal Plate
HDD Cushion (Black)
15    1
* Notes:1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
Only the metal plate 
attached on this side
Displace the edge by 
10 mm and fold back.
Prepare the metal plate bend.
Do not bend it at a sharp 
angle to put natural R.To the level of attaching 
closely in this range  When attaching HDD Cushion (Yellow) and HDD Cushion (Black), 
set the bending part of the metal plate up.
Metal Plate
Remove the Release Paper. 
						

							9-33
(10)
Attach the HDD Cushion (Yellow) Attach the HDD Cushion (Yellow)
Attach the HDD Cushion (Black)
Attach the HDD thermal Plate
1   2
1   21   2
0    1
0    1
1   2
HDD Cushion 
(Black)
* Notes:
HDD Thermal Plate
1. Apply the load when attaching the parts.  20N to 30N (2 to 3Kgf)/cm\
2
Fold back matching 4 corners. Do not bend it at a sharp 
angle to put natural R.
To the level of attaching 
closely in this range
Prepare the metal plate bend When attaching HDD Cushion Plate and HDD Cushion (Black), 
set the bending part of the metal plate up.
Longer Direction
Metal Plate
*Ensure the direction is right. (lateral) Keep the space to secure the air vent.Put the edge on the same line.  
Difference:    1 
						

							9-34
A-A SECB-B SEC
A
(2)(4)
(4)
11   1
(0)
(20)
HDD Side Damper is installed
HDD Side Damper
B
B
A
0    0.5
HDD Bottom Case Ass’y
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
Right and left position: Match to the center
Top and bottom position: Match the edge of the base material transparent\
 
                                         sheet to the bottom sideLower Case
(Entire Circumference) 
						

							9-35
NG
HDD Ass’y insertionSATA Guard is installed
Insert to make the Cushion on the HDD 
inside of the Cushion on the lower case. Avoid getting HDD under the side 
damper when inserting HDD
Set the CN side first, and then set the 
TAB side pushing to the A direction.
A
SATA Guide Set
Tighten of 
Screw   Tighten of 
Screw  Tighten of 
Screw  
Tighten of 
Screw  
Tighten of Screw 
Attach the Edition Number Label
7    2
5    2
Order of fixing
Screw Screw Screw Screw* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
Confirm that the CN board moves up/down 
and right/left after assembling. Label Letters : head is top 
						

							9-36
9.2.19. Setting the  Battery Pack and HDD Pack
1. Set the HDD Pack.
2. Set the Battery Pack.
Battery
Cover
HDD Cover
HDD Pack
Battery Pack 
						

							C F -30C T Q A Z xx
10 E x plo de d  V ie w
N4
K116
K93
E24
K92K24
K84
N4
K78
N5
K74
K77
K76
N4
K90
K109
E13E21
K1-3
K1-17
K1-1
K1-17
K1-5
K1-6
K1-4
K1-15
K1-4
K1-16
K1-12K1-8
K1-12
K1-2
K1
E17
K1-7
K35
K1-9
N5
N5
N2
K32
K33K35
N5
K2
K1-14
K82
K19
K23
K129
K25
K26
K25
K25
K95
K87
E23
N5
N7N10
N10
K115
E4
N4
N4N4N4
N4
N4
N4
K17
K30
N2
K29K70
K75
K71
K16
N4N4N4
E1001
K73
K73
K73
AAA
B
B
B
BB
A
VV
Screw tightening torque
         0.19 _ 0.02 N.m         (2.0 _ 0.2 kgf.cm)
         0.45 _ 0.05 N.m         (4.5 _ 0.5 kgf.cm)
         0.49 _ 0.05 N.m
         (5.0 _ 0.5 kgf.cm)
         1.47 _ 0.20 N.m         (15 _ 2.0 kgf.cm)
         0.18 _ 0.22 N.m         (2.0 _ 0.2 kgf.cm)
         0.2 _ 0.02 N.m
         (2.0 _ 0.2 kgf.cm)
A
B
F
G
I
L
++
++
++
++
++
+
+
B
BBB
BB
BBB
B
G
G
B
A
B
A
K1-10K1-18K1-11
K1-13
B
K162
10-1 
						

							CF-30CTQAZxx
K2-10
K2-10-8
K2-10-8K2-10-2
K2-10-1
K2-10-3
K2-10-1
K2-39
K2-39
K2-10-8 K2-10-4
K2-10-6K2-10-7K2-16K2-4
K2-4-3 K2-4-1
K2-4-2
K2-36
K2-36
K2-43
K2-43
K2-22K2-16
K2-1 K2-1-3
K2-1-2K2-1-1
K2-2-4
K2-2-3
K2-42
K2-42K2-2-1K2-37
K2-2-5
K2
K2-27
K2-44
K2-26K2-41
K112
K104
K101
K100
N4
K122
K2-5-3
K2-16
K2-3
K2-5
K2-5-2
K2-5-1
K2-5-4
K2-16
K2-3-4 K2-3-3 K2-3-1
K2-6-5
K2-6-1 K2-39K2-6-1
N1
K81
K2-8-5 K2-8-4K2-8-10
K2-8-10 K2-8-1 K2-8-1
K2-39 K2-8-8
K2-39
K2-8-7K2-8-9
K2-8
K2-8-11
N4K121
K114
K105 K113
K2-7-4
K2-7-2
K2-7
K2-39
K2-39 K2-7-1
K2-7-1
K2-9-10
K2-9-9
K2-9-9
K2-9-9 K2-9-5
K2-9-4K2-9-7
K2-9-2 K2-9-2
K2-9-1
K2-9-8
K2-9
K2-31
K2-42
K106K36
K2-15
K2-21
K2-22
K2-16
K108
K2-25
K2-25
K2-38
K2-38
K2-24 K2-20
K2-18
K2-18
K107
K2-8-2
K2-14
K2-14K2-13
K103
K102
K2-23
K2-8-3
K2-8-3
K2-17
K2-17
K2-3-2
K2-4-4
K2-41
K2-6-2 K2-6
K2-6-4
K2-6-3
K2-6-3K2-10-5
K2-30
K2-9-6
K2-9-3 K2-7-3
K2-8-6
K2-2-2
K2-2-6 K2-2
K2-2-7
K163
Q
RR
B
RB
R
R
T
B
L
L
L
B
B
R
R
L
B
T
B
B
RR
LL
L
R
G
Screw 
tightening  torque
         0.19  ± 0.02  N.m
          (2.0 ± 0.2  kgf.cm)
         0.45  ± 0.05  N.m
          (4.5 ± 0.5  kgf.cm)
         1.47  ± 0.20  N.m
          (15.0  ± 2.0  kgf.cm)
         0.2 ± 0.02  N.m
          (2.0 ± 0.2kgf.cm)
         0.22  ± 0.02  N.m
          (2.2 ± 0.2  kgf.cm)
         0.30  ± 0.05  N.m
          (3.0 ± 0.5  kgf.cm)
         0.90  ± 0.05  N.m
          (9.0 ± 0.5  kgf.cm)A
B
G
L
Q
R
T
G
T
R
L
R
R
R
T
R
R
R
10-2