Panasonic Cf30 Service Manual

							9-19
24. Fix the Screw. 
25. Attach the TOP Screws.
Note: Tighten the Screws in the numbered order (No1 to No8).
Tighten the Screws in the numbered order (No1 to No6).
Screws : DRQT26+D4FKL
Screws : DRSB26+10HKL
Screws : DFHE5025XA
Screws : DRQT26+E5FKL
Screws : DRQT26+E6FKL
Screws : DRSB26+8FKL
Screws : DXQT2+E12FNL
 TOP Screw Sheet 
Connector
  (CN17) Connector
  (CN27) 
						

							9-20
Q
 Assembly of LAN, Modem and MDC
Q  Assembly of Main PCB
Safety Working 
MDC
5    1
15    1
Tighten of 
Screw  
Tighten of 
Screw  
Tighten of 
Screw   Tighten of 
Screw  
LAN Cable 
is installed.
Modem Cable 
is installed. Modem LAN Case
is installed.
Cable
Coil
Attach the DMD Cable Sheet
Order of fixing
Screw Screw
* Notes:
1. Apply the load when attaching the parts.   20N to 30N (2 to 3Kgf)/c\
m2
Pass the Cable to the back 
from the hole of the A side. (Remove  2 places)Match to the edge of the Connector.   1 Process the cable and cover 
with MDM Cable SheetSeparate from the coil.
Attach space
Safety Working 
Safety Working 
Attach the PET Sheet
0    1
0    1
1    2Cable SATA Signal Insertion 
Sheet wrapSafety Working 
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Insert the connector wrapped with the 
sheet into the connector on the board.Bend the cable avoiding the connector.
Connect the LAN cable.
Put the cable in a U-shape into the intermediate 
chassis aperture next to the Connector.
Insert the FFC of the card 
connector into the connector 
on the main board.
Insert the FFC of the card connector into 
the connector on the main board.
Do not insert the connector incompletely.  
(Note: Insert diagonally.) 
						

							9-21
9.2.11. Setting the PAD PCB
1. Fix the PAD PCB using the 2 Screws. 
2. Attach the TP PCB Screw Sheet.
3. Connect the Cable to the Connector. (CN802)
4. Connect the Cable to the Connector (CN801) and attach
the Tape.
Screws : DRQT26+D3FKL
Q  Assembly of PAD PCB


Pad PCB
Connector
 (CN802)
Connector
 (CN801)
Tape
TP PCB Screw Sheet
Safety Working 
Safety Working 
Safety Working 
Safety Working 
Safety Working 
Safety Working 
Attach the 
Cable Sheet0    2
LED PCB
Attach the Touch Pad INS Sheet
0    2
7    11
7    11
0    2
0    2
FFC Insertion
FFC Insertion
Attach the Touch 
Pad FFC Fix Tape
Tighten of 
Screw   Tighten of 
Screw  
Attach the Touch Pad 
PCB Screw SheetCable Hold Sheet 
is installed
* Notes:1. Apply the load when attaching the parts.    20N to 30N (2 to 3Kgf)/cm2\
Avoid running over the boss and the rib.
Process the surplus 
of FFC to the back. Screw Screw
Insert the boss at an angle to put here close to the Cabinet side.  Process the SP cable between the bosses.
PCB Pad is set
Attach the Tape
Fit to the Cabinet line.
Attach the Tape
Fit to the Cabinet line.
Process the wire targeting the boss. Do not insert the Connector at an angle.
Order of fixing
PCB Pad
CN Connection  After connecting, add the kapton tape. 
						

							9-22
9.2.12. Setting the FPC HDD  BAT
1. Fix the FPC HDD BAT using the Screw. 
2. Connect the 2 Cables to the 2 Connectors. (CN7,CN8)
3. Connect the Cable to the Connector. (CN800)
4. Attach the PAD Protect Sheet.
5. Connect the Cable to the Connector. (CN9)
6. Attach the Tape.
7. Connect the 2 Cables to the 2 Connectors. (CN10,CN26)
8. Attach the Tape.
9. Attach the Antenna Cable Sheet on the Main PCB.
10. Fix the HDD FPC BAT using the 5 Screws.  No1 to
No5
Note: Tighten the Screws in the numbered order (No1 to No5).
Screw : DRQT26+D3FKL
Screw : DRQT26+E5FKL
Q  Preparation of HDD FPC ASSY


 
Connector(CN10)Connector(CN26)
HDD Cable Cover FPC HDD BAT
Antenna Cable Sheet
to Connector (CN800)
Connector (CN800)
to Connector (CN26)
Tape
Connector(CN9)
Pad PCB
Tape
to Connector (CN8)
to Connector (CN7)
Connector
(CN8) Pad Protect
Sheet
Connector
(CN7)
No.3

No.2 
No.4
No.1
No.5
Not to forget folding
Tighten of 
Screw Tighten of 
Screw
Battery Connector PIN 
Cushion is set
Battery Connector 
PIN is setBattery Guide 
is set
Order of fixing
Screw Screw
Fold mountain based 
on the white line.
Not to forget folding 
						

							9-23
Tighten of Screw  Tighten of 
Screw 
Tighten of 
Screw 
HDD Guide is set
Battery HDD Connector 
Angle is set FPC HDD Battery is set
Direction A
View
A
B C
Direction C
View
Direction B
1. Set HDD Guide and fix with Screw.
2. Fix with Screw.
3. Apply tetra coating to each connector pin.
This Connector does not need tetra coating.
Do not Fold. 
(R1    4)
View 
						

							9-24
9.2.13. Setting the USB PCB and Antenna PCB
1. Open the Connector Cover.
2. Fix the Antenna PCB using the 2 Screws. 
3. Connect the 2 white Cables.
4. Fix the USB PCB using the Screws. 
5. Connect the Cable to the Connector. (CN100)
6. Attach the Tape.
Screws : DRQT2+G6FKL
Screws : DRQT26+D4FKL
FPC
The attention of folding   : Breakage countermeasure.
1,The bending inside is R0.5   1
2,Don’t mistake a bending direction. Don’t use a mistaken thing.
(R0.5   1)
NGOK
Figure seen from direction of arrow of A The terminal of the antenna
cable must not come in
contact with this terminal.
(Put it on the metal fittings
side. )
Cable
Relay Circuit Board Ass’y
Insert FPC into Relay Circuit Board Ass’ys socket
FPC
Mountain Fold (Straight Line)
Valley Fold (Dotted Line) Insert the Plug 
into the Socket
Lock after FPC insertion FIG
FPC A



USB PCB Connector
 (CN100)
Antenna PCB Connector Cover
Antenna Cable
     (White)
Antenna Cable
     (White) Tape 
						

							9-25
Q
 Assembly  of  USB PCB and Antenna PCB
Tighten of 
Screw  
Tighten of 
Screw  
Tighten of Screw
EXT Antenna PCB 
is setW-LAN Cable 
Connection
Safety Working Safety Working 
Attach the Tape
Attach the Antenna Cable Sheet
Antenna Cable 
Plate is set
Order of fixingScrew Screw
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2\
Connect the coaxial cable from LCD.
Set on the top. Process the cable from LCD.Fit to the groove.  
Difference : 1 or less
Along the groove
Pull W-LAN Cable out to the surface from the hole.
Safety Working 
Cable USB is set
PCB USB Sub is set
Tighten of Screw
* Notes:
1. Apply the load when attaching the parts.   20N to 30N (2 to 3Kgf)/c\
m2
Match to the CN edge.  
Difference: less than 1 Match to the board edge. 
Difference: less than 1
Attach the kapton tape into CD Edge Sheet. 
						

							9-26
9.2.14. Setting the DIMM  Cover and Bottom Cover
1. Set the Bottom Cover.
2. Fix the Bottom Cover using the 6 Screws.  No1 to No6
3. Fix the Bottom Cover using the 13 Screws.  No1 to
No13
4. Set the DIMM memory card.
5. Attach the DIMM Heat Plate.
6. Fix the DIMM Stopper Base using the 2 Screws. 
7. Fix the DIMM Cover using the 5 Screws. 
Screws : DRHM0002ZA
Screws : DRQT26+D4FKL
Screws : DRQT26+E4FKL
Screws : DRSB3+8FKL
Note: Tighten the Screws in the numbered order (No1 to No6).
Tighten the Screws in the numbered order (No1 to No13).
Tighten the Screws in the numbered order (No1 to No5).
  




 


 
Bottom Cover
DIMM Memory Card
DIMM Stopper Base
DIMM Heat Plate
DIMM Cover
 





 No.4
No.5
No.2
No.3
No.1
No.1No.2 No.3
No.4
No.5
No.6
No.8
 No.7
No.9

No.10
No.11No.12
No.13
No.1
No.2
No.3 No.4
No.5

No.6 
						

							9-27
Q
 Preparation of DIMM Cover
LCD Cable Cover is set Keyboard Cable Cover is installed
Attach the LCD Cable Cover Cushion Attach the Keyboard Cable Cover Cushion
Safety Working 
Safety Working 
Attach the CD Edge Sheet Attach the CD Edge Sheet
4    6mm
4    6mm
0    1mm
1.5    2.5mm
* Notes:
1. Apply the load when attaching the attaching parts. 20N to 30N (2 to \
3Kgf)/cm2
0    0.5mm
0    0.5mm
0    0.5mm
0    0.5mm
DIMM Cover is set
Attach the DIMM Cover Cushion
Attach the DIMM Cover Spacer
* Notes:
1. Apply the load when attaching the parts.  20N to 30N (2 to 3Kgf)/cm\
2 
						

							9-28
9.2.15. Setting the GPS PCB and Bluetooth PCB
1. Fix the GPS BT Angle and GPS PCB using the 2 Screws.

2. Connect the Cable to the Connector on GPS PCB.
3. Fix the GPS Ass’y using the 4 Screws. 
4. Connect the Cable to the Connector. (CN25)
Screws : DFHE5025XA
Screws : DXQT2+F3FNL
Q  Cautions for Setting GPS ASSY and BT PCB ASSY
GPS PCB
Bluetooth
PCB
Connector(CN25)
 
GPS BT Angle



to Connector
(CN25)
Safety Working 
Safety Working 
Safety Working 
8   1
10    2
Main Antenna
Sub Antenna
Bluetooth Cable
Whip Antenna Cable
Whip Antenna Cable
Main Antenna Cable GPS Antenna Cable
0    2
0    2
Sub Antenna Cable
* Notes:
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Fit to the plate squeeze line.    1
Attach the Tape
Put the Cable along 
the Cabinet side and 
tape it firmly.
Match to the boss center.
Cabinet Level Standard 
Tolerance 0 to 1 
Process the wire into the groove. Pass the Cable behind 
the Cabinet protrusion.
Attach the Cable Sheet into 
Main Cable and Whip Cable. Attach the Cable Sheet into 
Sub Cable and GPS Cable.
Ensure that the wrapping 
direction is right. Avoid coming over the groove.
Ensure that the wrapping 
direction is right.Connect into the coaxial Connector.
Process the wire to the 
back from the aperture.
Insert the 
cable plug.
Process the wire of whip ANT cable from 
LCD to the back from the aperture.
1. Do not gouge when inserting and removing the plug.
2. Do not damage the coating when handling the cable.
Bluetooth Cable
GPS Antenna