Panasonic Cf 52 Service Manual
Have a look at the manual Panasonic Cf 52 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
9-29 9.2.18. Setting the Speakers 1. Place the Speakers on the computer. 2. Connect the Cables to the Connector(CN4202 and CN4203). 3. Paste the Tape on the Cable. 4. Attach the Speaker Holder R to the computer.Note: Do not attach the Speaker Holder L to the computer yet. 9.2.19. Setting the Modem 1. Connect the Cable to the Connector. 2. Paste the Tape2, Conductive Tape-Modem and Tape1. 3. Fix the Modem to the SW LED MDC PCB using the two Screws . Screws : DFHE5122YA Cable Cable CN4202 CN4203 Speaker holder R Speaker R Speaker L Tape Modem CN4200 SW LED MDC PCB Cable
![](/img/blank.gif)
9-31 9.2.20. Setting the Handle Ass’y 1. Assemle the Handle Ass’y (Grip Upper, Grip Lower, Handle Base L, Handle Base R, Handle Ring and Handle Pom), and fixthem using the two Screws . 2. Fix the Handle Base Ass’y to the computer using the two Screws . Paste the Handle Sheet on the Screws . Screws : DRSB3+8FKLT Screws : DRYN4+J12KLT Grip upper Handle ring Handle ring Handle pom Handle pom Handle ring Grip lower Handle base L Handle base R Handle ring Handle sheet Handle sheet
![](/img/blank.gif)
9-32 9.2.21. Setting the LCD Unit, Inverter Ass’y and Antenna PWB L, R 1. Set the LCD Unit to the LCD Rear Cover 2. Fix the Inverter Ass’y using the Screw . 3. Fix the Anttena PWB L and R using the Screws . 4. Place the LCD Front on the LCD Rear Case. Confirm that the twenty-one Hooks are fixed perfectly. 5. Fix the LCD Front using the five Screws and two Screws . 6. Paste the LCD Screw Sheet and LCD Rubber. Screws : DFHE5122YA Screw : DRHM0093ZA Screws : DXSB2+4FNLT Screws : XQN17+BJ6FJ Cable Inverter assy Cable Tape LCD rear cover ANTENNA PWB R LCD unit ANTENNA PWB L LCD rubber LCD rubber LCD screw sheet LCD screw sheet LCD screw sheet Hooks Hooks Hooks Hooks Hooks LCD front Hooks
![](/img/blank.gif)
9-33 ■ Setting of LCD unit ass’y LCD LCD DAMPER A LCD DAMPER B LCD DAMPER C LCD DAMPER D LCD Gap within 0.5mm Gasket Using JIG Using JIG LCD CABLE LCD Insert LCD CABLE surely þ÷44 SHEET SHIELD SHEET A LCD SHEET SHIELD SHEET B Schematic for sticking at Point A LCD Paster Gasket Alminium (silvery) paster is stuck on the gasket. th Bending Pressurizing range Range of pressurizing The cloth conductor shall be stuck along the gasket.
![](/img/blank.gif)
9-34 üwÿ44 ADHESIVE TAPE B ADHESIVE TAPE B Do not exceed the edge. Do not exceed the edge.Do not exceed the edge. ADHESIVE TAPE A
![](/img/blank.gif)
9-35 Attention: The heat-resistant adhesive tape shall be stuck onto the part surely. Tape shall not cover the round hole Along the slot ù÷44ù÷44 S5 S5 The Cable is under the base plate Along the slot Tape shall not cover the round hole LCD REAR COVER HINGE L TAPE PWB ANT L PWB ANT R LCD DAMPER E SCREW SCREW SCREW SCREW TAPE LCD DAMPER E HINGE R CAUTIONS1:Insulation S2:Pinching Cables S3:Sharp Edge S4:Part No. Check S5:Others Safety Working
![](/img/blank.gif)
9-36 LCD ASSY Note: Paster shall be firmly stuck andNote: Paster shall be firmly stuck anddoes not float.does not float. SHEET There are total 12 gaskets indicated by yellow arrows which must be installed surely. Refer to the specification pictures on the left. OKOK NGNG Note: Do not exceed the edge of the metal frame