Panasonic Cf 52 Service Manual

9-28
■
Caution for when assembling the Keyboard. 

9-29
9.2.18. Setting the Speakers
1. Place the Speakers on the computer.
2. Connect the Cables to the Connector(CN4202 and CN4203).
3. Paste the Tape on the Cable.
4. Attach the Speaker Holder R to the computer.Note:
Do not attach the Speaker Holder L to the computer yet.
9.2.19. Setting the Modem
1. Connect the Cable to the Connector.
2. Paste the Tape2, Conductive Tape-Modem and Tape1.
3. Fix the Modem to the SW LED MDC PCB using the two Screws .
Screws  : DFHE5122YA
Cable Cable
CN4202
CN4203 Speaker...

9-30
■
How to paste the Tape 

9-31
9.2.20. Setting the Handle Ass’y
1. Assemle the Handle Ass’y (Grip Upper, Grip Lower, Handle Base L, Handle Base R, Handle Ring and Handle Pom), and fixthem using the two Screws .
2. Fix the Handle Base Ass’y to the computer using the two Screws .
Paste the Handle Sheet on the Screws .
Screws : DRSB3+8FKLT
Screws : DRYN4+J12KLT
Grip upper
Handle
ring Handle
ring
Handle
pom
Handle
pom
Handle
ring
Grip
lower
Handle
base L

 
Handle
base R
Handle
ring Handle
sheet
Handle
sheet 

9-32
9.2.21. Setting the LCD Unit, Inverter Ass’y and Antenna PWB L, R
1. Set the LCD Unit to the LCD Rear Cover
2. Fix the Inverter Ass’y using the Screw . 
3. Fix the Anttena PWB L and R using the Screws .
4. Place the LCD Front on the LCD Rear Case.
Confirm that the twenty-one Hooks are fixed perfectly. 5. Fix the LCD Front using the five  Screws  and two Screws .
6. Paste the LCD Screw Sheet and LCD Rubber.
Screws  : DFHE5122YA
Screw  : DRHM0093ZA
Screws  : DXSB2+4FNLT
Screws  : XQN17+BJ6FJ

Cable...

9-33
■
Setting of LCD unit ass’y
LCD
LCD DAMPER A
LCD DAMPER B
LCD DAMPER C
LCD DAMPER D
LCD  
 
Gap within 0.5mm
Gasket
Using JIG
Using JIG
LCD CABLE LCD
Insert LCD CABLE surely
þ÷
4
4
SHEET
SHIELD SHEET A
LCD SHEET
SHIELD SHEET B
Schematic for sticking at Point A
LCD
Paster
Gasket
Alminium (silvery) paster is stuck on the gasket.
th







Bending
Pressurizing range
Range of
pressurizing
The cloth conductor shall be stuck along the gasket. 

9-34
üwÿ
4
4
ADHESIVE TAPE B
ADHESIVE TAPE B
Do not exceed
the edge.
Do not exceed
the edge.Do not exceed
the edge.
ADHESIVE TAPE A 

9-35
Attention: The heat-resistant adhesive tape
                 shall be stuck onto the part surely.
Tape shall not cover the round hole
Along the slot
ù÷
4
4ù÷
4
4
S5
S5
The Cable is under
the base plate
Along the slot
Tape shall not cover the round hole
LCD REAR COVER
HINGE L TAPE
PWB ANT L
PWB ANT R
LCD DAMPER E SCREW
SCREW SCREW
SCREW
TAPE
LCD DAMPER E HINGE R
CAUTIONS1:Insulation  S2:Pinching Cables  S3:Sharp Edge
S4:Part No. Check  S5:Others
Safety Working 

9-36
LCD ASSY
Note: Paster shall be firmly stuck andNote: Paster shall be firmly stuck anddoes not float.does not float.
SHEET
There are total 12 gaskets indicated by yellow
arrows which must be installed surely.
Refer to the specification pictures on the left.
OKOK
NGNG
Note:
Do not exceed the
edge of the metal
frame 

9-37