Panasonic Cd Stereo System Sc-max670 Owners Manual

							11VQT5F35ENGLISH
You can change the transmission speed to prioritize 
transmission quality or sound quality.
Preparation
If this system is connected to a Bluetooth
® device, 
disconnect it ( >“Disconnecting a device”).
1
Press [PLAY MENU] to select “LINK MODE”.
2
Press [ 2,1] to select “MODE 1” or “MODE 2” 
and then press [OK].
Note:
The default setting is “MODE 2”.1
Press [PLAY MENU] repeatedly to select 
“DISCONNECT?”.
2
Press [ 2,1] to select “OK? YES” and then 
press [OK].
Note:
A device is disconnected when you:
• Select a different source.
• Move the device out of the maximum range.
• Disable the Bluetooth
® transmission of the device.
• Switch off the system or the device.
Clock and timersThis is a 12-hour clock.1
Press [CLOCK/TIMER] to select “CLOCK”.
2
Within 20 seconds, press [ 3,4] to set the time.
3
Press [OK].
Press [CLOCK/TIMER] to show the clock for a few 
seconds.
Note:
• Reset the clock regularly to maintain accuracy.
• The clock is reset when there is a power failure or when the  AC power supply cord is removed.
Except for Bluetooth
® source
You can set the timer to come on at a certain time to:
• Wake you up
Preparation
Set the clock.
1
Press [CLOCK/TIMER] to select “ PLAY”.
2
Within 10 seconds, press [ 3,4] to set the start 
time.
3
Press [OK].
4
Do steps 2 and 3 again to set the end time.
5
Press [ 3,4] to select the source you want to 
play and then press [OK].
To start the timer
1
Prepare the audio source.
Prepare the music source you want to listen to (disc, 
USB, radio or external equipment) and set the 
volume.
2
Press [PLAY ] to select “ PLAY ON”.
“ PLAY ON” is shown.
To cancel, press [PLAY ] again.
The system must be switched off for the timer to 
operate.
To check the settings
Press [CLOCK/TIMER] to select “ PLAY”.
Note:
• The play timer starts at a low volume and increases  gradually to the preset level.
• The timer comes on at the set time every day if the timer is  on.
Link mode•MODE 1
Emphasis on connectivity.
•MODE 2 Emphasis on sound quality.Disconnecting a device
Setting the clock
Play timer
SC-MAX670P_eng.book  11 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							VQT5F35
12
The sleep timer switches off the system after the set 
time.
Press [SLEEP] to select the setting (in minutes).
To cancel, select “OFF”.
Note:• The sleep timer always comes first. Be sure not to set an overlap of timers.
Sound and illuminationYou can adjust the sound effect.1
Press [SOUND] to select the sound effect.
2
Press [ 2,1] to select the desired setting.
Preset EQ
Press [PRESET EQ] to select desired preset.
Using the main unit
You can adjust certain sound effect using the controls on 
the main unit.
1
Press the button to select the sound effect.
2
Turn [MULTI CONTROL] to select the desired 
setting.
By main unit only
You can change the illumination pattern or color on this 
system.
Turn [ILLUMINATION] to select pattern or color.
Note:
To ensure the illumination effects are shown properly, make 
sure to arrange the speakers accordingly as in “Placement of 
speakers”.
Sleep timer30 MIN
>
60 MIN
>
90 MIN
>
120 MIN
>
OFF
^=================n
Adjust the sound effect• BASS/MID/TREBLE -4 to +4
• SURROUND
“ON SURROUND” or “OFF SURROUND”
• INPUT LEVEL (For AUX IN 2)
“NORMAL” or “HIGH”
Note:Select “NORMAL” if the sound is distorted during 
“HIGH” input level.• SUPER WOOFER“SW1”, “SW2”, “SW3” or “OFF”
• D.BASS “D.BASS ON”, “D.BASS BEAT” or “D.BASS OFF”
Note:
D.BASS BEAT: This function emphasizes the 
attack level of the drum beat and produces a 
punchy sound.
• Depending on the type of a track, the effect may  be small. • PRESET EQ
Press [PRESET EQ]
• BASS/MID/TREBLE Press [MANUAL EQ]
• D.BASS
Press [D.BASS,-SUPER WOOFER]
• SUPER WOOFER Press and hold [D.BASS,-SUPER WOOFER]
Illumination effects•PATTERN
Illuminate with pattern in multiple colors.
•COLOR Illuminate in one color.
•OFF
SC-MAX670P_eng.book  12 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							13VQT5F35ENGLISH
DJ functionsDJ functions has the following functions
- DJ jukebox
- DJ sampler
- DJ effects
Using these functions, you can add various effects to the 
track you are playing back., 
This mode adds a crossfade effect or sample sound mix 
to the intervals between the tracks you play back.
This function works when you play back the tracks in the 
USB device.1
Press [DJ JUKEBOX] on main unit.
• The setting of the unit switches to repeat mode  automatically.
• (In the stop mode only) You can change the  desired repeat setting by turning [MULTI 
CONTROL] on main unit.-RANDOM REPEATPlay all tracks randomly.
-ALL TITLE REPEAT Repeat all tracks.• When displayed WAITING REQUEST on the 
display, you can proceed to the next step without 
using the app Panasonic MAX Juke.
2
Press [1] to [6] on main unit to select the desired 
function.
To cancel, press the button again.
To cancel the DJ jukebox
Press [DJ JUKEBOX] on main unit.
Note:
• To change DJ jukebox function ON or OFF with the remote  control1 Press [PLAY MENU] to select “JUKEBOX”.
2 Press [ 2,1] to select “ON JUKEBOX” or “OFF 
JUKEBOX“ and then press [OK].• To change the desired repeat setting with the remote 
control1 Press [PLAY MENU] twice to select “PLAYMODE”.
2 Press [ 2,1] to select desired mode and then press 
[OK]. By main unit only
By turning [MULTI CONTROL], you can apply a scratch sound 
or sample sound to the track you are playing back.1
Press [DJ SAMPLER].
2
Press [1] to [6] to select the desired sound.
3
Turn [MULTI CONTROL].
To cancel the DJ sampler
Press [DJ SAMPLER].
By main unit only
You can use the DJ effect function to add the sound effects.1
Press [DJ EFFECT].
2
Press [1] to [6] to select the desired DJ effect.
To cancel, press the button again.
3
Turn [MULTI CONTROL] to select the desired setting.
To cancel the DJ effect
Press [DJ EFFECT].
If you use the app “Panasonic MAX Juke”
By installing the app “Panasonic MAX Juke” (free of 
charge) on your Android device, you can use a wider 
variety of functions.
Download the app “Panasonic MAX Juke” to your 
Android device. Enter “Panasonic MAX Juke” in the 
search box of Google Play to search, and then select 
“Panasonic MAX Juke”.
DJ jukebox
•[1]Crossfade:
 The playback track volume gradually 
becomes small and next track volume becomes large.
•[2] to [6]
Sample Sound Mix:  This effect is sounding a 
sample sound to the intervals between the tracks 
you play back.
If you use the app “Panasonic MAX Juke”
You can call up the tracks you want to play back through 
the app.
• When displayed “MAKING LIST” on the display, you  can call up a part of tracks.
• When displayed WAITING REQUEST on the  display, you can call up the tracks you want to play 
back through the app.
DJ samplerIf you use the app “Panasonic MAX Juke”• You can change the sample sound on the app. (To return all sample sounds to the factory preset, press and 
hold [DJ SAMPLER] when the DJ sampler is turned off.)DJ effects•[1] PHASER
Add space and dimension to the sound.
•[2] FILTER
Enhance or filter specific ranges of the sound.
•[3] SOUND CHOPPER
Cut off the sound periodically.
•[4] ELECTRO ECHO
Add digital echo to the sound.
•[5] PITCH SHIFTER
Adjust the keys of the sound.
•[6] HARMONIZER
Add notes to the sound to create harmony.
SC-MAX670P_eng.book  13 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							VQT5F35
14
Using a microphonePreparation
Decrease the volume of the system to its minimum 
before you connect or disconnect a microphone.1
Connect a microphone (not supplied) to the 
microphone jack.
Plug type: ‰ 6.3 mm (1/4 z) monaural
2
Turn [MIC VOL, MIN/MAX] on the main unit to 
adjust the volume of the microphone.
3
If you want to sing with the background music.
Play the music source and adjust the volume of 
the system.
Note:
• If a strange noise (howling) is emitted, move the  microphone away from the speakers, or decrease the 
volume of the microphone.
• When you do not use the microphone, disconnect it from  the microphone jack, and decrease the volume of the 
microphone level to “MIN”.
Using the auxiliary inputPreparation
• Disconnect the AC power supply cord.
• Switch off all equipment and read the appropriate 
operating instructions.
Note:
Components and cables are sold separately.
You can play music from a portable audio equipment.
Preparation
Switch off the equalizer (if any) of the portable audio 
equipment to prevent sound distortion.
Decrease the volume of the system and the portable 
audio equipment before you connect or disconnect the 
portable audio equipment.1
Connect the portable audio equipment to 
AUX IN 2.
Plug type:  ‰3.5 mm (1/8z ) stereo (not supplied)
2
Press [RADIO/EXT-IN] to select “AUX 2”.
3
Play the portable audio equipment. You can connect a VCR, DVD player etc. and listen to 
the audio through this system.
1
Connect the external equipment.
2
Press [RADIO/EXT-IN] to select “AUX 1”.
3
Play the external equipment.
Note:
• If you want to connect equipment other than those  described, refer to the audio dealer.
• Sound distortion can occur when you use an adapter.
To connect a portable audio equipment etc.
To connect a VCR, DVD player etc.
DVD player (not supplied)
Audio cable
(not supplied)
Rear panel of this main unit
SC-MAX670P_eng.book  14 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							15VQT5F35ENGLISH
TroubleshootingBefore requesting service, make the following checks.
If you are in doubt about some of the check points, or if 
the solutions indicated do not solve the problem, consult 
your dealer for instructions.
The unit does not work.
• One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [ Í/I] on the main unit to switch the unit to 
standby.
• If the unit does not switch to standby, press [ Í/I] 
on the main unit for a few seconds. The unit is 
forcibly switched to standby. Alternatively, 
disconnect the AC power supply cord, wait one 
minute, then reconnect it.
2 Press [ Í/I] on the main unit to switch it on. If the 
unit still cannot be operated, consult the dealer.
The display panel lights up and changes 
continuously in standby mode.
• Press and hold [ ∫] on the main unit to select “DEMO 
OFF”.
No operations can be done with the remote control.
• Examine that the battery is installed correctly.
Sound is distorted or no sound.
• Adjust the volume of the system.
• Switch off the system, determine and correct the  cause, then switch the system on again. It can be 
caused by straining of the speakers through excessive 
volume or power, and when using the system in a hot 
environment.
A humming sound can be heard during playback.
• An AC power supply cord or fluorescent light is near  the cables. Keep other appliances and cords away 
from the cables of this system.
The sound level reduces.
• The protection circuit has been activated due to the  continuous use at high volume output. This is to 
protect the system and maintain the sound quality. Display not shown correctly.
Playback does not start.
• You have not put in the disc correctly. Put it in correctly.
• Disc is dirty. Clean the disc.
• Replace the disc if it is scratched, warped, or 
non-standard.
• There is condensation. Let the system dry for 1 to  2hours.
The total number of tracks displayed is incorrect.
The disc cannot be read.
Distorted sound is heard.
• You put in a disc that the system cannot play. Change  to a playable disc.
• You put in a disc that has not been finalized.
The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it  is/are not compatible with the system.
• USB devices with storage capacity of more than 32 GB  cannot work in some conditions.
Slow operation of the USB device.
• Large content size or large memory USB device takes  longer time to read.
Sound is distorted.
• Use an optional FM outdoor antenna. The antenna  should be installed by a competent technician.
A beat sound is heard.
• Switch off the TV or move it away from the system.
Stations cannot be selected.
• Change the FM frequency step. 1 Press [RADIO/EXT-IN] to select “FM”.
2 Press and hold [RADIO/EXT-IN] on the main unit.
After a few seconds, the display panel shows the 
current minimum radio frequency. Release the button 
when the minimum frequency changes. Pairing cannot be done.
• Check the Bluetooth
® device condition.
The device cannot be connected.
• The pairing of the device was unsuccessful. Do pairing again.
• The pairing of the device has been replaced. Do pairing again.
• This system might be connected to a different device. Disconnect the other device and try pairing the device 
again.
The device is connected but audio cannot be heard 
through the system.
• For some built-in Bluetooth
® devices, you have to set 
the audio output to “SC-MAX670” manually. Read the 
operating instructions of the device for details.
Sound from the device is interrupted.
• The device is out of the 10 m (33 ft) communication  range.
Move the device nearer to the system.
• Remove any obstacle between the system and the  device.
• Other devices that use the 2.4 GHz frequency band  (wireless router, microwaves, cordless phones, etc.) 
are interfering. Move the device nearer to the system 
and distance it from the other devices.
• Select “MODE 1” for stable communication.
The One-Touch Connection (NFC feature) is not 
working.
• Make sure the unit and the NFC feature of the device  are turned on. ( >p.10)
Common problems
DiscUSBRadio
Bluetooth
®
SC-MAX670P_eng.book  15 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							VQT5F35
16
“USB A NO DEVICE”
“USB B NO DEVICE”
• The USB device is not connected. Examine the connection.
“ERROR”
• An incorrect operation was done. Read the instructions  and try again.
“F61”
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and  then switch it on again.
“F70”
• Examine the Bluetooth
® device.
• Disconnect the Bluetooth® device. Switch off the 
system and then switch it on again.
“F77”
• Switch off the system and then switch it on again.
“NO PLAY”
“UNSUPPORT”
• Examine the content. You can only play supported  format.
• The files in the USB device can be corrupted. Format  the USB device and try again.
• The unit may have a problem. Turn the unit off and  then on again.
“NO TRACK”
• There is no album or track in the USB device.
“PLAYERROR”
• You played an unsupported MP3 file. The system will  skip that track and play the next one. “REMOTE 1”
“REMOTE 2”
• The remote control and the main unit are using 
different codes. Change the code of the remote 
control.
- When “REMOTE 1” is shown, press and hold [OK] and [1] for a minimum of 4 seconds.
- When “REMOTE 2” is shown, press and hold [OK]  and [2] for a minimum of 4 seconds.
“TEMP NG”
• The temperature protection circuit has been activated,  and the system will switch off. Let the unit cool down 
before switching it on again.
• Check that the ventilation opening of the unit is not  obstructed.
• Ensure this unit is well ventilated.
“USB OVER CURRENT ERROR”
• The USB device is using too much power. Disconnect the USB device, switch off the system and 
then switch on again.
“VBR”
• The system cannot show the remaining play time for  variable bit rate (VBR) tracks.
System memory reset (initialization)Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.1
Disconnect the AC power supply cord.
2
While you press and hold [ Í/I] on the main unit, 
connect the AC power supply cord again.
Continue to press and hold the button (approximately 
10 seconds) until “- - - - - - - -” is shown.
3
Release [ Í/I].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Remote control codeWhen other Panasonic equipment responds to the 
remote control of this system, change the remote control 
code for this system.
Preparation
Press [RADIO/EXT-IN] to select “AUX1” or “AUX2”.1
Press and hold [RADIO/EXT-IN] on the main unit 
and [2] on the remote control until “REMOTE 2” 
is shown.
2
Press and hold [OK] and [2] for a minimum of 
4 seconds.
1
Press and hold [RADIO/EXT-IN] on the main unit 
and [1] on the remote control until “REMOTE 1” 
is shown.
2
Press and hold [OK] and [1] for a minimum of 
4 seconds.
Main unit displays
To set the code to “REMOTE 2”To set the code to “REMOTE 1”
SC-MAX670P_eng.book  16 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							17VQT5F35ENGLISH
ReferenceOccasionally, Panasonic may release updated software 
for this unit that may add or improve the way a feature 
operates. These updates are available free of charge.
For more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Frequency band
• This system uses the 2.4 GHz frequency band.
Certification
• This system conforms to the frequency restrictions and has received certification based on frequency laws. 
Thus, a wireless permit is not necessary.
• The actions below are punishable by law:- Taking apart or modifying the main unit.
- Removing specification indications.Restrictions of use
• Wireless transmission and/or usage with all Bluetooth
® 
equipped devices is not guaranteed.
• All devices must conform to standards set by Bluetooth  SIG, Inc.
• Depending on the specifications and settings of a device, it  can fail to connect or some operations can be different.• This system supports Bluetooth
® security features. But 
depending on the operating environment and/or 
settings, this security is possibly not sufficient. 
Transmit data wirelessly to this system with caution.
• This system cannot transmit data to a Bluetooth
® 
device.
Range of use
• Use this device at a maximum range of 10 m.
• The range can decrease depending on the  environment, obstacles or interference. Interference from other devices
• This system may not function properly and troubles 
such as noise and sound jumps may arise due to radio 
wave interference if this unit is located too close to 
other Bluetooth
® devices or the devices that use the 
2.4 GHz band.
• This system may not function properly if radio waves  from a nearby broadcasting station, etc. is too strong.
Intended usage
• This system is for normal, general use only.
• Do not use this system near an equipment or in an  environment that is sensitive to radio frequency 
interference (example: airports, hospitals, laboratories, 
etc.). This system may keep the user settings information 
internally. If you discard this system either by disposal or 
transfer, then follow the procedure to return all the 
settings to the factory presets to delete the user settings.
- To return all sample sounds to the factory preset (refer 
to page 13).
- To reset system memory (refer to page 16).
Note:
• The operation history may be recorded in the memory of  this system.
Software updateAbout Bluetooth
®
Panasonic bears no responsibility for data and/or 
information that can possibly be compromised during a 
wireless transmission.
LicensesMPEG Layer-3 audio coding technology licensed from 
Fraunhofer IIS and Thomson.
The Bluetooth
® word mark and logos are owned by the Bluetooth 
SIG, Inc. and any use of such marks by Panasonic Corporation is 
under license.
Other trademarks and trade names are those of their respective 
owners.
Google Play and Android are trademarks of Google Inc.
To dispose or transfer this system
SC-MAX670P_eng.book  17 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							VQT5F35
18
SpecificationsRMS output power (each channel driven)High 400+400 W  (3™, 1 kHz, 30% THD)
Mid-Low 400+400 W (3™, 1 kHz, 30% THD)
Low 850+850 W (5™, 100 Hz, 30% THD)
Total RMS output power  3300 W (30% THD)
FTC Output Power High 200+200 W  (2 kHz to 20 kHz, 1%, 3™)
Mid-Low 200+200 W  (80Hzto4kHz,1%,3™)
Low 200+200 W (50Hzto170Hz,1%,5™)
Disc played  8cm (3 z) CD, CD-R/RW
12 cm (5 z) CD, CD-R/RW
Pick up Wavelength 790 nm  (CD)
Laser power CLASS I
Audio output (disc) 2ch (FL, FR)
FL = Front left channel
FR = Front right channel
Format CD-DA, MP3
Frequency modulation (FM) Preset memory 30 stations
Frequency range 87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals  75™ unbalanced Ty p e
  4 way, 4 speaker system (bass reflex)
Speaker unit(s) Super Woofer (Low)  38 cm (15z ) cone type
Super Woofer (Mid-Low)  20 cm
 (77/8z ) cone type
Woofer 10 cm  (4z) cone type
Tweeter 6 cm  (23/8z) cone type
Impedance  High 3 ™/ Mid-Low 3 ™/ Low 5 ™
Output sound pressure   91 dB/W (1 m (3.3 ft))
Frequency range  25 Hz to 23 kHz (-16 dB)
30 Hz to 20 kHz (-10 dB)
Ve r s i o n Bluetooth
® Ver.2 .1 + E DR
Output Class 2 (2.5 mW)
Communication distance
Prospective communication distance: About 10 m (33 ft)*
Communication method 2.4 GHz band FH-SS
Correspondence profile A2DP/AVRCP/SPP
* Prospective communication distanceMicrophone jackMono, ‰ 6.3 mm (1/4 z)
USB port USB standard  USB 2.0 full speed
Media file format support  MP3 (*.mp3)
USB device file system  FAT12, FAT16, FAT32
AUX input  Terminal Stereo,  ‰3.5 mm (1/8 z) jack
Stereo, Pin jack Power supply
  AC 120 V, 60 Hz
SA-MAX670P
Power consumption  330 W
Dimensions (W x H x D) 492mm x 221mm x 421mm
19
3/8z x 8
23/32z  x 16
19/32z
Mass (Weight) Approx. 7.1 k
g (15.66 lbs)
SB-MAX670P
Dimensions (W x H x D) Including the speaker feet:  576mm x 794mm x 542mm
22
11/16z x 31
1/4z x 21
11/32z
Excluding the speaker feet:  576mm x 786mm x 542mm
22
11/16z x 30
15/16z  x 21
11/32z
Mass (Weight) Approx. 37.4 k
g (82.4 lbs)
Operating temperature range  0°C to +40°C
Operating humidity range 35% to 80% RH (no condensation)
Note:
• Specifications are subject to change without notice. Mass  and dimensions are approximate.
• Total harmonic distortion is measured by the digital  spectrum analyzer.
Amplifier sectionDisc sectionTuner section
Speaker sectionBluetooth
® section
Measurement environment:
Temperature 25 °C 
(77
oF )/
Height 1.0 m (3.3 ft)
Measure in “MODE 1”
Terminals section
GeneralPower consumption in standby mode
0.2 W (approximate)
SC-MAX670P_eng.book  18 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							19VQT5F35ENGLISH
Limited WarrantyPanasonic Products Limited 
WarrantyLimited Warranty Coverage
(For USA Only)If your product does not work properly because of a defect in materials or 
workmanship, Panasonic Corporation of North America (referred to as “the 
warrantor”) will, for the length of the period indicated on the chart below, 
which starts with the date of original purchase (“warranty period”), at its 
option either (a) repair your product with new or refurbished parts, (b) 
replace it with a new or a refurbished equivalent value product, or (c) 
refund your purchase price. The decision to repair, replace or refund will be 
made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During 
the “Parts” warranty period, there will be no charge for parts. This Limited 
Warranty excludes both parts and labor for non-rechargeable batteries, 
antennas, and cosmetic parts (cabinet). This warranty only applies to 
products purchased and serviced in the United States. This warranty is 
extended only to the original purchaser of a new product which was not 
sold “as is”.Mail-In Service
--Online Repair Request
Online Repair RequestTo submit a new repair request and for quick repair status visit our Web 
Site at www.panasonic.com/repair
.
When shipping the unit, carefully pack, include all supplied accessories 
listed in the Owner’s Manual, and send it prepaid, adequately insured and 
packed well in a carton box. When shipping Lithium Ion batteries please 
visit our Web Site at www.panasonic.com/BatteryHandling
 as Panasonic is 
committed to 
providing the most up to date information.  Include a letter detailing the 
complaint, a return address and provide a daytime phone number where 
you can be reached. A valid registered receipt is required under the Limited 
Warrant y.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And ExclusionsThis warranty ONLY COVERS failures due to defects in materials or 
workmanship, and DOES NOT COVER normal wear and tear or cosmetic 
damage. The warranty ALSO DOES NOT COVER damages which 
occurred in shipment, or failures which are caused by products not 
supplied by the warrantor, or failures which result from accidents, misuse, 
abuse, neglect, mishandling, misapplication, alteration, faulty installation, 
set-up adjustments, misadjustment of consumer controls, improper 
maintenance, power line surge, lightning damage, modification, 
introduction of sand, humidity or liquids, commercial use such as hotel, 
office, restaurant, or other business or rental use of the product, or service 
by anyone other than a Factory Service Center or other Authorized 
Servicer, or damage that is attributable to acts of God.THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED 
UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR 
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF 
THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS 
WARRANTY. (As examples, this excludes damages for lost time, travel to and from the 
servicer, loss of or damage to media or images, data or other memory or 
recorded content. The items listed are not exclusive, but for illustration 
only.)ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE 
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE 
PERIOD OF THE LIMITED WARRANTY.Some states do not allow the exclusion or limitation of incidental or 
consequential damages, or limitations on how long an implied warranty 
lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other 
rights which vary from state to state. If a problem with this product develops 
during or after the warranty period, you may contact your dealer or Service 
Center. If the problem is not handled to your satisfaction, then write to the 
warrantor’s Consumer Affairs Department at the addresses listed for the 
warrantor.PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS 
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
As of April 2014
Product or Part Name Parts LaborCD Stereo System 1 Year 1 Year
 All included Accessories
(Except Non-Rechargeable Batteries) 90 Days Not Applicable
Only Non-Rechargeable Batteries 10 Days Not Applicable
Customer Services Directory (United States)Obtain Product Information and Operating Assistance; locate 
your nearest Dealer or Service Center; purchase Parts and 
Accessories; or make Customer Service and Literature requests 
by visiting our Web Site at:
http://www.panasonic.com/supportor, contact us via the web at:
http://www.panasonic.com/contactinfoFor hearing or speech impaired TTY users, TTY: 
1-877-833-8855 
Accessory Purchases (United States)Purchase Parts, Accessories and Owner’s Manual online for all 
Panasonic Products by visiting our Web Site at: 
http://www.pstc.panasonic.comOr, send your request by E-mail to: 
[email protected] may also contact us directly at:
1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic National Parts Center
20421 84th Avenue South., Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express)For hearing or speech impaired TTY users, TTY: 
1-866-605-1277 The model number and serial number of this product 
can be found on either the back or the bottom of the 
unit.
Please note them in the space provided below and 
keep for future reference.
MODEL NUMBER
SC-MAX670
SERIAL NUMBER User memo: DATE OF PURCHASE 
DEALER NAME 
DEALER ADDRESS
TELEPHONE NUMBER
SC-MAX670P_eng.book  19 ページ  ２０１４年２月２６日　水曜日　午後５時４９分 
						

							VQT5F35
20
Cómo realizar las conexiones
1
Conecte los altavoces.
Conecte los cables de los altavoces a los terminales 
del mismo color.
2
Conecte la antena interior de FM.
Coloque la antena donde la recepción sea mejor.
3
Conecte el cable de alimentación de CA.
Utilice solamente el adaptador de CA suministrado.
Disco
1
Pulse [ OPEN/CLOSE] en la unidad principal 
para abrir la bandeja del disco.
Coloque un disco con la etiqueta hacia arriba.
Pulse [ OPEN/CLOSE] nuevamente para cerrar la 
bandeja del disco.
2
Pulse [CD] y después pulse [1
/;] para iniciar la 
reproducción.
1
Pulse [PLAY MENU] para seleccionar 
“PLAYMODE” o “REPEAT”.
2
Pulse [2
, 1
] y después pulse [OK] para 
seleccionar el modo deseado.
Nota:
La configuración vuelve al “OFF PLAYMODE” 
predeterminado cuando usted abre la bandeja del disco.
Esta función le permite programar hasta 24 pistas.1
Pulse [PROGRAM] en modo de detención.
Se visualiza “PGM” o “PROGRAM”.
2
Pulse los botones numéricos para seleccionar la 
pista deseada.
Realice este paso nuevamente para programar otras 
pistas.1 Pulse [3
, 4
] para seleccionar el álbum deseado.
2 Pulse [9] y después pulse los botones 
numéricos para seleccionar la pista deseada.
3 Pulse [OK].
Realice estos pasos nuevamente para programar 
otras pistas.
3
Pulse [ 1
/;] para iniciar la reproducción.
Nota:
• Usted no puede utilizar la reproducción de programa con la  función “PLAYMODE”.
• La memoria del programa se borra cuando se abre la  bandeja de disco.
Referencia rápida en españolReproducción del disco• Detener la reproducción
Pulse [ ∫].
• Hacer una pausa en la reproducción
Pulse [ 1/;].
Pulse nuevamente para continuar la reproducción.
• Saltear un álbum  Pulse [ 3,4].
• Saltear una pista
Pulse [ :] o [9 ]
(unidad principal: [ :/6 ] o [5 /9 ]).
• Examinar la pista
Mantenga pulsado [ 6] o [5 ]
(unidad principal: [ :/6 ] o [5 /9 ]).
Menú de reproducciónPLAYMODE
• OFF PLAYMODE
Reproduce todas las pistas.
• 1-TRACK Reproducir una pista seleccionada del disco.
Pulse los botones numéricos para seleccionar la 
pista.
• 1-ALBUM  Reproducir un álbum seleccionado del disco.
Pulse [ 3,4] para seleccionar el álbum.
• RANDOM
Reproduce un disco aleatoriamente.
• 1-ALBUM RANDOM  Reproducir todas las pistas de un álbum 
seleccionado aleatoriamente.
Pulse [ 3,4] para seleccionar el álbum.
REPEAT
• ON REPEAT Repite la reproducción.
Aparece “ `”.
• OFF REPEAT Cancela la repetición de la reproducción.
Reproducción de programa• Cancela el modo de programa Pulse [PROGRAM] en el modo detenido.
• Verifica el contenido del programa
Pulse [ :] o [9 ] cuando se muestre “PGM” 
en el modo de detenido.
• Borra la última pista Pulse [DEL] en el modo detenido.
• Borra todas las pistas programadas Pulse [ ∫] en el modo detenido.
Se visualiza “CLR ALL”.
Dentro de 5 segundos, pulse [ ∫] nuevamente.
SC-MAX670P_eng.book  20 ページ  ２０１４年２月２６日　水曜日　午後５時４９分