Panasonic Camera Controller Ak Hrp900p Operating Instructions

11
ZOOM
REVERSEFOCUS
REVERSENOR REV NOR REV
TU
_Front panel
TZoom operation lever direction change switch [ZOOM REVERSE]
Used to change the direction of the zoom operation lever.
With this switch set at [NOR], when the zoom operation lever :is shifted to [TELE], the
zoom operates in a telescopic mode, and when shifted to [WIDE], zooming is made in a
wide angle mode.
With this switch set to [REV], it can be operated in the opposite direction.  Also, with this
switch set to [REV], the operating direction...

12
Make the connection with power supply to the unit turned off.
≥Use AW-PS505P (option) as the AC adapter for control panel.
≥Use a swivel stand, AW-PH300A, AW-PH500, AW-PH600, and an adapter suited for
the swivel stand.
≥When no swivel stand is used, connect both of the motor-driven zoom lens iris control
cable and remote (zoom/focus) cable to the camera. (see page 13)
≥When a swivel stand is used, connect the iris control cable to the camera, and the
remote (zoom/focus) cable to the swivel stand. (see...

13 _Lens connection in the case of no swivel stand
_How to mount the lens
≥A lens of any maker’s can be used provided that it is a bayonet type (B4 mount) lens
of 2/3 inch standard.*
1Turn the lens fixing ring knob counterclockwise and remove the lens mount cap.
2Mount the lens and completely secure it by turning the lens fixing ring knob
clockwise.
3Connect the iris control cable to the lens connector.
4Connect the remote (zoom/focus control) cable to the zoom/focus connector on the
rear panel.
*Note...

14
O    I
BREAKER
ZOOM/
FOCUS
SDI OUT1
2
1
/F
POWERON OFFSD  CARDOPERATE
ALARMSCENE
MODEPRE
CAM BAR TESTUSER1 USER2Camera  Controller
TA L LY
MENU
ON
MENU
SPEED ZOOMTELE
WIDEFA R
NEARFOCUS12345PRESETCC  FLTER3200CROSS6300 4300ND  FLTER11/321/16 1/4SHUTTER
OFFSYNCROSTEPGAIN0S1 S2
S39dB 18dB
AUTO
WHITE BLACKGAINBLACK
AUTO M-PEDIRISCHECK
Multi-cable (17ft)
AK-HDMLTCA05
Camera controller
AK-HRP900P D-SUB 15-pin
D-SUB 15-pinHD monitor
AC adapter
AW-PS505P
Ext. sync signal (3-value SYNC)
DC power
cable Coaxial...

15
Multi-purpose digital camera control system configuration 2
O    I
BREAKER
ZOOM/
FOCUS
SDI OUT1
2
1
/F
G/L I N Pb  OUT Pr / SDI
OUTY/ VIDEO
OUT
1394CONTROL IN
IP/RPDC12V
IN
CAMERA I/F
LENSE I/F
ND/EXT SDI
IN
CSOP
O    I
POWERON OFFSD  CARDOPERATE
ALARMSCENE
MODEPRE
CAM BAR TESTUSER1 USER2Camera  Controller
TALLY
MENU
ON
MENU
SPEED ZOOMTELE
WIDEFA R
NEARFOCUS12345PRESETCC  FLTER3200CROSS6300 4300ND  FLTER11/321/16 1/4SHUTTER
OFFSYNCROSTEPGAIN0S1 S2
S39dB 18dB
AUTO
WHITE BLACKGAINBLACK
AUTO...

16
Multi-purpose digital camera control system configuration 3
O    I
BREAKER
ZOOM/
FOCUS
SDI OUT1
2
1
/F
G/L I N Pb  OUT Pr / SDI
OUTY/ VIDEO
OUT
1394CONTROL IN
IP/RPDC12V
IN
CAMERA I/F
LENSE I/F
ND/EXT SDI
IN
CSOP
O    I
O    I
POWERON OFFSD  CARDOPERATE
ALARMSCENE
MODEPRE
CAM BAR TESTUSER1 USER2Camera  Controller
TA L LY
MENU
ON
MENU
SPEED ZOOMTELE
WIDEFA R
NEARFOCUS12345PRESETCC  FLTER3200CROSS6300 4300ND  FLTER11/321/16 1/4SHUTTER
OFFSYNCROSTEPGAIN0S1 S2
S39dB 18dB
AUTO
WHITE BLACKGAINBLACK
AUTO...

17
The communication speed is factory-adjusted to 38.4Kpbs.
In case it does not match the communication speed of multi-purpose camera AK-HC900P,
the alarm LED is lighted.  Remove the rear panel and change the DIP SW on the board
and adjust it to the communication speed of the camera.
SW3
ON
1234
ON
1234
ON
1234
ON
1234
5678
Change the
communication report
by the combination of
SW3 No.1 and No.2 on
ROP CPU board.125Kbit/Sec
38.4Kbit/Sec
9600Kbit/Sec
SW5 SW4 SW3
Remove the
screw and open
the bottom
plate,...

18 _How to rack-mount
Install the main body on the rack as shown below.
Remove the rack mount
bracket screw when installing
Rack mount bracket 
Attached 
screwCoupler
Coupler
fitting
holes
Example of Rack Mount 

CAMERA  I / F
MONITOR  OUT G/L  IN TALLY  IN
BREAKERDC  12V  IN
YPbPr
P/T  CONT
CAMERA  I / F
MONITOR  OUT G/L  IN TALLY  IN
BREAKERDC  12V  IN
YPbPr
P/T  CONT
19 _How to change the rear panel position
1Remove the three screws on the
bottom to remove the blank panel.
* When installing, take care so that the internal wires are not caught by the panel.3Install the rear panel on the bottom with
the three screws.
Screw Screw
Screw Blank panel
Blank panel
Example of Rack Mount
Screw
2Remove the three screws...

20
Appearance and Dimensions
(   ): mm
ZOOM
REVERSEFOCUS
REVERSENOR REV NOR REV
CAMERA  I / F
MONITOR  OUT G/L  IN TALLY  IN
BREAKERDC  12V  IN
YPbPr
P/T  CONT
POWERON OFF
SD  CARDOPERATE
ALARMSCENE
MODEPRE
CAM BAR TESTUSER1 USER2Camera  Controller
TALLY
MENU
ON
MENU
SPEED ZOOMTELE
WIDEFA R
NEARFOCUS
12345PRESETCC  FLTER3200CROSS6300 4300ND  FLTER11/321/16 1/4
SHUTTER
OFFSYNCROSTEPGAIN0S1 S2
S39dB 18dB
AUTO
WHITE BLACK
GAINBLACK
AUTO M-PED
IRISCHECK
8-5/16z (210)
6-15/16z (176) 5/8z 
(14.5) 2-1/4z...