Panasonic Bluray Disc Home Theater Sound System Sc Btt750 Operating Instructions

							Getting started 
11
VQT2W18
ASpeaker cable sticker  (supplied)
B Connector
Be sure to match the number on each sticker with the 
connector color.
	≥ Be careful not to cross (short-circuit) or reverse the polarity of the 
speaker wires as doing so may damage the speakers.
≥ Don’t use a front speaker as a surround speaker or vice versa. Verify 
the type of speaker with the label on the rear of the speaker before 
connecting the appropriate cable.
≥ To avoid injury by falling or dropping the speaker, place the speaker cables 
with care not to stumble or hook.
≥ Do not hold the speaker in one hand to avoid injury by dropping the 
speaker when carrying.
Preparing cables and making connection
Speaker cable stickerColor
1 FRONT (L) WHITE
2 FRONT (R) RED
3 SURROUND (L) BLUE
4 SURROUND (R) GRAY
5 CENTER GREEN
6 SUBWOOFER PURPLE
FRONT
Lch


1
 
Use of the speaker cable stickers is 
convenient when making cable connections.
e.g. Front speaker (L)2
Push!
Connecting the speaker cables. Insert the wire fully, 
taking care not to insert beyond the wire insulation.
r: White
s: Blue line
e.g. Surround speaker
SC-BTT750_350P_VQT2W18_eng.book  11 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							12
VQT2W18
STEP 2 : Positioning
How you set up your speakers can affect the bass and the sound field.
Setup example
Place the front, center and surround speakers at 
approximately the same distance from the seating position.
The angles in the diagram are approximate.
	≥Keep your speakers at least 10 mm (13/32z) away from the system for 
proper ventilation.
A Center speaker
≥Put on a rack or shelf not to interfere with the TVs 
various sensors (ambient light, etc.). Vibration caused by 
the speaker can disrupt the pict ure if it is placed directly 
on the TV.
B Front speakers
C Subwoofer
D Surround speakers
≥Place the speakers at the same height or higher than ear 
level.
	≥ Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be 
negatively affected.
≥ You can damage your speakers and shorten their useful life if you play 
sound at high levels over extended periods.
≥ Positioning speakers in front
It is possible to locate all the speakers in front of the listening position. 
However, the optimal surround sound effect may not be obtainable.
≥ Place speakers on flat secure bases.
≥ Placing speakers too close to floors, walls, and corners can result in 
excessive bass. Cover walls and windows with thick curtains.
≥ For optional wall mount, refer to page 41.
∫ If irregular coloring occurs on your TV, turn 
the TV off for about 30 minutes.
If it persists, move the speakers further away from the TV.
∫Upgrade your system to 7.1-channel 
system
The main unit is designed to enjoy the 7.1ch surround sound. By 
connecting 2 units of the Panasonic wireless system SH-FX71 
with 4 speakers, more theater-like effect can be available.
Necessary equipment:
≥2 optional wireless systems (SH-FX71)
≥ 2 additional speakers
[Impedance: 3  ≠ to 6  ≠, Speaker input power: 100 W (Min)]
For more details, refer to the operating instructions for the 
optional wireless system.
Caution
≥ The main unit and supplied speakers are to be used only as indicated in this setup. Failure to do so may 
lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified 
service person if damage has occurred or if you experience a sudden change in performance.
≥ Do not attempt to attach these speakers to walls us ing methods other than those described in this 
manual.
≥ Do not touch the front netted area of the speakers. Hold by the sides.
 You can enjoy surround speaker 
sound wirelessly when you use the 
optional Panasonic wireless 
accessory (SH-FX71).
For more details, refer to the operating 
instructions for the optional wireless 
system.
120°60°

 

 
SC-BTT750_350P_VQT2W18_eng.book  12 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							Getting started 
13
VQT2W18
STEP 3: Connections
Turn off all equipment before connection and read the appropriate operating instructions.
Do not connect the AC power supply cord until all other connections are complete.
Connect to the terminals of the same color.
Use outdoor antenna if FM radio reception is poor.
Speaker cable connection
-
+
5 2
1366FRONTCENTER
SUBWOOFERRL4
33SURROUNDRL
+
6

 


Main unit
6
PURPLE Subwoofer
5 GREEN Center speaker
2 RED Front speaker (Rch) 
1 WHITE Front speaker (Lch)
4 GRAY Surround speaker (Rch)
3 BLUE Surround speaker (Lch)
When using the optional wireless 
system, do not attempt to connect 
any extra surround or surround 
back speakers to the main unit.
Radio antenna connection
Using an indoor antenna
Using an outdoor antenna

FM ANT
(75    )Ω
Main unit
AFM indoor antenna  (supplied)
B Adhesive  tape
Affix this end of the antenna where reception is 
best.

 
FM ANT (75    )ΩA
FM outdoor antenna  [Using a TV antenna
(not supplied)]
The antenna should be installed by a competent 
technician.
B 75 ≠ coaxial cable (not supplied)
C Antenna plug  (not supplied)
Main unit
e.g.,
SC-BTT750_350P_VQT2W18_eng.book  13 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							14
VQT2W18
≥The basic connection is shown in the included Easy Setting Gui de, however, there are more connection examples to optimize 
your system setting.
≥ This system supports the PCM and the Dolby Digital bitstream i nput audio. However, for example the system does not support 
the DTS bitstream input audio.
	≥ Do not make the video connections through the VCR.
Due to copy guard protection, the pi cture may not be displayed properly.
≥ Turn off all equipment before connection.
∫ OPTICAL IN
≥After making the digital audio connection, make settings to 
suit the type of audio from your digital equipment ( >29).
∫ HDMI
The HDMI connection supports VIERA Link “HDAVI Control” 
(> 30) when used with a compatible Panasonic TV.
≥ Please use High Speed HDMI Cables that have the HDMI 
logo (as shown on the cover). It is recommended that you 
use Panasonic’s HDMI cable. When outputting 1080p signal, 
please use HDMI cables 5.0 me ters (16.4 ft.) or less.
Recommended part number (High Speed HDMI Cable):
RP-CDHS15 (1.5 m/4.9 ft.), RP-CDHS30 (3.0 m/9.8 ft.), 
RP-CDHS50 (5.0 m/16.4 ft.), etc.
≥ Audio will be output through the systems speakers when 
“Off” is selected in “HDMI Audio Output”. ( >38)
Connection to a TV
Basic connection
AUXL
RVIDEO OUT
L
VIDEO IN
R 
AUDIO IN
LR 
AUDIO OUT


VIDEO OUT
AUX
TV
A Audio cable  (not supplied)
B Video cable  (supplied)
To enjoy TV audio from this home theater 
system’s speakers
1 Connect the TV and the main unit with the 
Audio cable (not supplied).
2 Select “AUX” as a source (> 22)
.
Connection for the better audio
L
ROPTICAL
DIGITAL AUDIO IN
VIDEO OUT(STB/TV)
OPTICAL
OUT
L
VIDEO IN
R 
AUDIO IN

OPTICALVIDEO OUT
TV
A
Video cable  (supplied)
B Optical digital audio cable (not supplied)
To enjoy TV audio from this home theater 
system’s speakers
1 Connect the TV and the main unit with the 
Optical digital audio cable (not supplied).
2 Select “DIGITAL IN” or “D-IN” as a source  (>22).
SC-BTT750_350P_VQT2W18_eng.book  14 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							Getting started 
15
VQT2W18
≥It is possible to playback 3D videos by c onnecting this unit with a 3D compatible TV.
ARC (Audio Return Channel)
(Available when using an ARC compatible TV)
With this function it is possible to receive the digital audi o signal from the TV without connecting any other audio cables. Be  sure 
to connect to the TV’s ARC compatible terminal.
≥ Select “ARC” as the audio input source ( >22).
≥ Refer to the operating instructions of the TV for the settings to output digital audio.
Connection for the best picture and audio
L
R
AV
OUTOPTICAL
DIGITAL AUDIO IN
(ARC)
(STB/TV)
OPTICAL
OUTAV IN
 
OPTICAL
HDMI AV OUT (ARC)
TV
A
HDMI cable (not supplied)
B Optical digital audio cable  (not supplied)
≥For the TV audio, an audio cable (not supplied) can 
be also used by connecting the AUX terminal with 
the AUDIO OUT terminal on the TV.
To enjoy TV audio from this home theater 
system’s speakers
1 Connect the TV and the main unit with the 
Optical digital audio cable (not supplied).
2 Select “DIGITAL IN” or “D-IN” as a source  (>22).
Connection with Set Top Box, etc.
L
ROPTICAL
DIGITAL AUDIO IN(STB/TV)
OPTICAL OUT


OPTICAL
TV
A Optical digital audio cable  (not supplied)
B Set Top Box (Cable/Satellite), etc.
Refer to the operating instructions of the respective 
devices for the optimal connections.
To enjoy TV audio from this home theater 
system’s speakers
1 Connect the STB and the main unit with the 
Optical digital audio cable (not supplied).
2 Select “DIGITAL IN” or “D-IN” as a source  (>22).e.g.,
SC-BTT750_350P_VQT2W18_eng.book  15 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							16
VQT2W18
The following services can be used when this unit is connected to broadband.
≥ Firmware can be updated  (> 20)
≥ You can enjoy BD-Live ( >26)
≥ You can enjoy VIERA CAST ( >33) For details about connection method, refer to the instructions 
supplied with the connected equipment.
Connection to a broadband network
∫
Using LAN (ethernet) cable ∫[BTT750] Using supplied Wireless LAN 
Adaptor
∫
[BTT350]  Using optional Wireless LAN 
Adaptor (DY-WL10)
A LAN Cable (not supplied)
B Broadband router, etc.
C LAN Cable (not supplied)
D Modem (Broadband) *Provided by ISP A
Wireless LAN Adaptor
B Wireless router (Access point), etc.
C LAN Cable (not supplied)
D Modem (Broadband) *Provided by ISP
≥ Use shielded LAN cables when connecting to peripheral 
devices.
≥ Inserting any cable other than a LAN cable in the LAN 
terminal can damage the unit. ≥
For up to date compatibility information on your Wireless 
router (Access Point) refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
≥ The unit is not compatible with public wireless LAN 
services provided in airports, stations, cafes etc.
For additional information about this unit refer to 
http://www.panasonic.com/consumer/support
[BTT750]
≥ Wireless LAN Adaptors other than the supplied Wireless 
LAN Adaptor cannot be used.
≥ When connection conditions are poor, use the supplied 
USB extension cable to connec t the Wireless LAN Adaptor 
provided with this unit.
≥ Do not use any other USB extension cables except the 
supplied one.
[BTT350]
≥ Only the Wireless LAN Adaptor DY-WL10 (optional) can 
be used.
≥
Read the operating instructions for the Wireless LAN Adaptor 
DY-WL10 (optional) thoroughly when using it.
L
RLAN




LR
DC OUT
5V
500mA
LANWIRELESS




SC-BTT750_350P_VQT2W18_eng.book  16 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							Getting started 
17
VQT2W18
[BTT750] Precautions of Wireless LAN AdaptorThe following limits are in place regarding the usage of this device. You must be aware 
of these limits before using this device.
Panasonic will in no way be responsible for any incidental damage which may arise due to 
a failure to obey these limits, or to any condition of use or disuse of this device.
≥Do not use this device to connect to any wireless network for which 
you do not have usage rights.
During automatic searches in a wireless network environment, wireless networks 
(SSID*) for which you do not have usage rights may be displayed; however, 
using these networks may be regarded as  illegal access.
* An SSID (Service Set IDentification) is a name used by wireless LAN to 
identify a particular network. Transmission is possible if the SSID 
matches for both devices.
≥ Data transmitted and received over radio waves may be intercepted 
and monitored.
≥
This wireless LAN adaptor contains delicate electronic components.Please use this adaptor in the manner in which it was intended and 
follow the following points:
– Do not expose the adaptor to high temperatures or direct sunlight.
– Do not bend, or subject the adaptor to strong impacts.
– Keep the adaptor away from moisture.
– Do not disassemble or alter the adaptor in any way.
– Do not attempt to install the adaptor in any incompatible device.
[BTT750]This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired 
operation of this device.
This transmitter must not be co-located or operated in conjunction with any 
other antenna or transmitter.
This product is restricted to indoor use due to its operation in the 5.15 to 
5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency 
range 5.15 to 5.25 GHz to reduce the potential for harmful interference to 
co-channel Mobile Satellite systems. High power radars are allocated as 
primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These 
radar stations can cause interference with and/or damage this product.
The available scientific evidence does not show that any health problems 
are associated with using low power wireless devices.
There is no proof, however, that these low power wireless devices are 
absolutely safe.
Low power Wireless devices emit low levels of radio frequency energy 
(RF) in the microwave range while being used.
Whereas high levels of RF can produce health effects (by heating tissue), 
exposure to low-level RF that does not produce heating effects causes no 
known adverse health effects.
Many studies of low-level RF exposures have not found any biological 
effects. Some studies have suggested that some biological effects might 
occur, but such findings have not been confirmed by additional research.
Wireless LAN adaptor (DY-WL10) has been tested and found to comply 
with FCC/IC radiation exposure limits set forth for an uncontrolled 
equipment and meets the FCC radio frequency (RF) Exposure Guidelines 
in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) 
Exposure rules.
[BTT750]
FCC Note:This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 
communications.
However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC caution: To maintain compliance with FCC regulations, shielded 
interface cables must be used with this equipment. Operation with 
non-approved equipment or unshielded cables may result in interference 
to radio and TV reception. Any changes or modifications not approved by 
the party responsible for compliance could void the user’s authority to 
operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including 
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
[BTT750]Product Identification Marking is located on the bottom of the Wireless 
LAN Adaptor.
SC-BTT750_350P_VQT2W18_eng.book  17 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							18
VQT2W18
STEP 4: AC power supply cord connection
AAC power supply cord  (supplied)
B To a household AC outlet
≥ Connect only after all other connections are complete.
≥ The main unit consumes a small amount of AC power, even when it  is turned off (When the “Quick Start” setting is “Off”: approx. 
0.05 W). In the interest of power conservation, if you will not  be using this unit for a long time, unplug it from the household  AC 
outlet.
STEP 5: Easy setup
The Easy setup assists you to make necessary 
settings.
Follow the on-screen prompts to make basic settings for the 
system.
Preparation
Turn on your TV and select the appropriate video input mode 
(e.g., VIDEO 1, AV 1, HDMI, etc.) to suit the connections to this 
unit.
1Press [ Í].
2Follow the on-screen instructions and 
make the settings with [ 3,4,2,1] and 
press [OK].
Language
Select the language used on menu screen.
TV Aspect Select the aspect to suit your TV and preference.
Wireless System If a digital transmitter is inserted,
it is required to specify the current settings.
Speakers position Specify the positioning of the surround speakers.
Speaker check Check if the connection to each speaker is valid.
Speaker Output Make surround sound setting for speaker output.
TV Audio Select the audio input connection from your TV,
[item with “(TV)”].
Quick Start Speed of startup from power off is increased.
3Press [OK] several times to finish the “Easy 
setup”.
After completing “Easy setup”, you can perform “Network Easy 
Setting”.
	≥You can perform this setup anytime by selecting “Easy setup” in the Setup 
menu. ( >39)
≥ Language and TV Aspect settings are automatically retrieved if this unit is 
connected to a Panasonic TV (VIERA) supporting HDAVI Control 2 or later 
via an HDMI cable.
-
+AC IN
             
Main unit
The unit should be installed near an accessible AC power outlet, with the power cord connected directly to it.
To completely disconnect power from the unit,  unplug the power cord from the AC power outlet.
OKOK
SC-BTT750_350P_VQT2W18_eng.book  18 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							Getting started 
19
VQT2W18
1Select “Wired” or “Wireless” and press 
[OK].
If “Wireless LAN Adaptor is not connected.” is displayed, check 
that the Wireless LAN Adaptor is fully inserted. Alternatively, 
disconnect and reconnect it. If there is still no change in the 
display, consult your dealer.
2Follow the on-screen instructions and 
make the settings with [3,4,2, 1] and 
press [OK].
For wireless LAN connection:
If you are using a Wireless router (Access point) that supports 
WPS, you can easily perform the  settings by selecting “WPS 
(PUSH button method)”.
Otherwise, perform the settings by selecting “Search for 
access point” or “Manual setting” in “Other methods”.
≥ WPS (Wi-Fi Protected Setup) is a function that facilitates 
settings relating to the connection and security of wireless 
LAN devices. To see whether your Wireless router (Access 
point) supports WPS, check the Wireless router operating 
instructions. Access Point Connection Setting
Network Easy Setting (Connection Check)
Network Easy Setting
OKRETURN
Network Easy Setting (Connection Check)
Wired
Wireless
Select a connection mode. 
 Current setting  :  Wired
 
LAN cable connection:
 Connect a LAN cable to the unit and select "Wired."
Wireless LAN connection:
 Connect the Wireless LAN Adaptor (DY-WL10) to the USB 
 port and select "Wireless."
OKRETURN
Access Point Connection SettingSelect a connection method to use with an access point 
of Wireless LAN.
Please refer to the operating instructions of the access
point about connection methods.
WPS (PUSH button method)
Other methods
p
WPS (PIN code method)Search for access point
Manual setting
When you experience 
problems with settings
DisplayCheck the following
A conflict with another 
device occurred. ≥
Please wait a few moments, 
and then try again.
A time out error occurred. ≥
Setting of the Wireless 
router (Access point) for 
MAC Address etc.
≥ [BTT750]  The signal may be 
weak. Using the supplied 
USB extension cable, adjust 
the position of the Wireless 
LAN Adaptor. Do not use 
any other USB extension 
cables except the supplied 
one.
≥ [BTT350]  The signal may be 
weak. Using the USB 
extension cable supplied 
with the Wireless LAN 
Adaptor, adjust the position 
of the Wireless LAN 
Adaptor.
≥ The SSID ( >20) and the 
encryption key of the 
Wireless router (Access 
point).
≥ Please wait a few moments, 
and then try again.
An authentication error or a 
time out error occurred.
A device error occurred.
≥
Connection of Wireless LAN 
Adaptor
If there is no improvement in 
symptom, contact our 
Customer Service Center.
DisplayCheck the 
following
1. LAN cable connection or 
Connection to access point :Fail≥
Connection of 
the LAN 
cables ( >16)
2. IP address setting :Fail
3. Connection to gateway :Fail
OK
Access Point Connection SettingFailed to connect to the access point.
A conflict with another device occurred.
Do you want to configure Access Point Connection
Setting again ?
Yes No
OK
Network Easy Setting (Connection Check)
YesNo
Complete.
1. LAN cable connection         
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
: Fail
: Fail
: Fail
SC-BTT750_350P_VQT2W18_eng.book  19 ページ  ２０１０年６月２１日　月曜日　午後４時５１分 
						

							20
VQT2W18
Network Easy Setting (Internet Connection Check)
	≥Refer to the operating instructions of the hub or router.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in 
the Setup menu. ( >39)
≥ You can redo these settings individually using “Network Settings”. ( >39)
≥ Do not use this device to connect to any wireless network for which 
you do not have usage rights.
During automatic seaches in a wireless network environment, wireless 
networks (SSID*) for which you do not have usage rights may be 
displayed; however, using these networks may be regarded as illegal 
access.
≥ After performing network settings on this unit, the settings (encryption level, 
etc.) of the Wireless router (Access point) might change. When you have 
trouble getting online on your PC, perform the network settings on your \
PC 
in accordance with the settings of Wireless router (Access point).
≥ Please be aware that connecting to a network without encryption may 
result in the content of the communication being illegitimately viewed by a 
third party, or the leaking of data such as personal or secret information.
* An SSID (Service Set IDentification) is a name used by wireless LAN to  identify a particular network. Transmission is possible if the SSID matches 
for both devices.
Occasionally, Panasonic may release updated firmware for this 
unit that may add or improve the way a feature operates. 
These updates are available free of charge.
This unit is capable of checking the firmware automatically 
when connected to the Internet via a broadband connection.
When a new firmware version is available, the following screen 
is displayed.
To update the firmware
Press [START]  > select “Other Functions”  > [OK]  > 
select  “Setup”  > [OK]  > select “Others” >  [OK]  > select 
“Firmware Update” >  [OK]  > select “Update Now”
If downloading on this unit fails or this unit is not connected to 
the Internet, then you can download the latest firmware from 
the following website and burn it to a CD-R to update the 
firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
To show the firmware version on this unit. ( >39, “System 
Information”)
DO NOT DISCONNECT the unit from the AC power or perform 
any operation while the update takes place.
After the firmware is installed, “FINISH” will be displayed on the 
unit’s display. Unit will restart and the following screen will be 
displayed.
	≥ Downloading will require several minutes. It may take longer or the Internet 
may not be connected depending on the connection environment.
≥ If you do not want to check for the latest firmware version, set “Automatic 
Update Check” to “Off”. ( >39)
1. LAN cable connection or 
Connection to access point :Pass
≥Connection 
and settings 
of the hub 
and router
≥ Settings of 
“IP Address / 
DNS 
Settings” 
(> 39)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection or 
Connection to access point
:Pass
2. IP address setting :Pass
3. Connection to gateway :Fail
DisplayCheck the following
Cannot find the server.
(Error code: B019) ≥
“Primary DNS” and “Secondary 
DNS” Settings of “IP Address / 
DNS Settings” ( >39)
Failed to connect to 
the server.
(Error code: B020) ≥
The server may be busy or the 
service may have been 
suspended. Please wait a few 
moments, and then try again.
≥ Settings of “Proxy Server 
Settings” (> 39) and the router.
OK
Network Easy Setting (Internet Connection Check)Complete.
- Connection to the Internet       :   Fail(Error code: B019)
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the operating instructions for the cause
of the error and the solution for it.
Press [OK].
Firmware updates
The latest firmware is available.
Please update firmware in Setup.
The firmware was updated.Current Installed Version: x.xx
RETURNOK
SC-BTT750_350P_VQT2W18_eng.book  20 ページ  ２０１０年６月２１日　月曜日　午後４時５１分