Panasonic All-in-One Headset Wx H3050 Operating Instructions

11
Communications with
Customers [TALK]
Any store personnel wearing the headset can communicate
bidirectionally with any customer who is at the menu board.
1. Select a proper sound level by pressing the ! or @  but-
ton.
2. You will hear a beep in the headset when a vehicle arrives at the menu board.

1. Hold down the T1 button and speak to the customer.A short beep is heard in the headset.
2. Release the button. Your voice is not heard by the cus- tomer.

1. Press the T1 button and speak to the...

Control of the device control ter-
minals
The device control terminals of the center module can be
controlled through the headset. 
1. Hold down the C button. A short beep is heard from the speaker of the headset and a connection will be made
toward the device control terminals of the center mod-
ule. 
2. Release the C button. A short beep is heard twice from the speaker of the headset and the connection will be
disconnected toward the device control terminals of the
center module. 
Double-Drive-Thru...

13
Manager Mode (Only one head-
set)
Complete ID Registration, to do this setting.
The headset set to the Manager mode has following func-
tionality.
• The manager can interrupt store personnels TALK or PAGE at any time by monopolizing one channel by prior-
ity.
• The Manager hears audio from POS alone.
1. Hold down the power button for two seconds or more to turn off the headset.
2. While holding R and T1 simultaneously, press the power button to turn on the headset. 
The headset enters manager setting...

14
Auto-Talk-Lock setup (for only
one headset)
For a headset where Auto-Talk-Lock is set up, it has a func-
tion to select [Talk] automatically when the vehicle detector
has become active, and you can talk with the customer at
the menu board. 
1. Confirm that the DIP Switch 1 of the headset is ON, the DIP Switch 2 is set at the objective lane, and the power
of the headset is OFF. 
2. Turn on the headset. The message Hello Headset ** (** is the number of headset) is output from the speaker of
the...

15
The head-pad cushion and earphone-pad are replaceable. Replace when nece\
ssary.
Head-pad cushion
Earphone-pad
Maintenance 

16
Caution:Setup of this product should only be performed by
qualified service personnel or system installers.
 Opening the Switch
Compartment
1. Press the power button  for 2 seconds or moreto turn off
the headset.
2. Unscrew the screw and open the switch compartment.
3. Set the switches as described below.
4. After finishing the setup, replace the cover.
5. Turn on the headset.
 DIP Switch Setup
An eight-bit DIP switch is provided for system setups. The
initial setting is marked with an asterisk *....

17
SW#8: This switch selects RF Power.ON: Reduce Power
OFF: Full power
 ID Registration
1. Press the ID Registration of the center module for 2 sec-
onds or more. The system is changed to the ID
Registration mode.
2. While holding down the T1 and T2 buttons simultaneous- ly, hold down the power button to turn on the headset.
The headset enters the ID Registration setting mode
where the indicators and buttons have different func-
tions than in normal operation. You will hear ID
Registration Mode and the...

18
The headset ID is not registered in the center module of the tar-
get.→ Register ID in the center module of the target. 
The battery is almost exhausted.
→ Recharge the battery. 
(Refer to the operating instructions of the battery charger.)
The center module may be turned off.
→ Turn on the power switch of the center module.  (Refer to the
operating instructions of the center module.) If no remedy
exists, consult your dealer for repairs.
The headset ID is not registered in the center module of the...

19
Operating Frequency:1 920 - 1 930 MHz
Required Power Supply: Rechargeable Li-ion Battery, 3.7 V DC
Control Function:  Power (On/Off)
Volume (Up/Down)
Talk (T1/T2)
Page
Lane Selection (A/B)
External Device Control (C)
DIP Switch Setup (8 bit)
Dimensions: 157 mm(W) x 269 mm(H) x 82 mm (D)
{6-3/16 (W) x 10-5/8 (H) x 3-1/4 (D)}
Weight (excluding battery): 150 g{0.33 lbs}
Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F}
Dimensions and weights indicated are approximate.
Specifications are...

20
Battery (Li-ion 3.7 V DC, 1 100 mAh)  ............................... WX-B3030
Battery Charger ................................................................ WX-Z3040
Optional Accessories
Standard Accessories
Operating Instructions (this manual) ................................ 1 pc.
Head protector  ................................................................. 2 pcs.