Panasonic Aj Ya901 Installation Guide
Have a look at the manual Panasonic Aj Ya901 Installation Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
SDI output Board AJ- Installation Guide P E EN ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL
![](/img/blank.gif)
E - 1 Connector Area (AJ-BS900) Serial digital output connectors (BNC x2) 1 Output 1: SDI output 2 Output 2: SDI output Y/G OP1 4:2:2 4:2:2 SDI OUT OUT OP4 OP3 WFM TALL YOP2 AUDIO OUT CH 1PUSHCH 2PUSHCATION PB/B PR/R WFM 2 SDI output 1SDI output Overview AJ-YA901P/E This SDI output board is designed for use with the AJ-BS900. Its installation in the AJ-BS900 enables digital data output using the SDI format. Overview/Connector Area Refer the installation of the SDI output board to qualified service personnel.
![](/img/blank.gif)
E - 2 ENGLISH EXT DC IN GEN– LOCKENC1 ENC2 ENC3 PIX Y/G 4:2:2 4:2:2 SDI OUT OUT IN OP4 OP3 WFM TALLYFUSE SIGNAL GND AC IN AUDIO OUT CH 1PUSHCH 2PUSHCOMMUNICATION PB/B PR/R WFMRET 1 RET 2 PROMPT OP1 OP2 1. 2. 3.4. Installation CABLESHORT ALARMF U S E H E A D P O W E R O N O F F M A I N O N O F F F U S EOPENDIGITAL TRIAXG E N L O C KOFF SC HC O A R S E INTERCOMP G MON OFFP T TM I CP R I V A T ES Y S T E MP U S H P H A S EV TR E N A B L EREW FF STOP S H U T T E RS E T U P M O N S E L K N E E P O I N T K N E E S L O P E G A M M AD E T A I L M .PE D O N O FF (PUSH) RG E N G S E QB SU PS.V S.S 100(60)1000120 250500 2000W H IT E B A L PLAY AWB C H E C KA U T O I R I S I R I SB RG A I NFILTER A B BB A R ENABLEPAINTING G A I NAUTO KNEE G A I N R E C C H KS T AR T / S T OPCALLTALLYVTR WARNINGPREA B B L A C K B a s e S ta t i o nA J - Follow the steps below to install the AJ-YA901 (referred to below as “the board”) in the AJ-BS900. Refer to the figure below, and remove the four screws from the rear panel of the AJ-BS900. Remove the two screws each from the left and right side panels of the AJ-BS900 to remove the side panels. Remove the two screws from the bottom panel of the AJ-BS900 to remove the bottom panel. 6.Remove the four screws on the front panel of the AJ- BS900, and pull off the front panel cover. (The screws cannot be removed from the front panel cover.) Pass the ends of the cables attached to the board from the position at the bottom shown in the figure below toward the top of the rear panel. Screws (x4) Screws (x2)Screws (x4) Side panel Bottom panel 5.Connect the cables, which were inserted into the AJ- BS900 in step 4, on the inner side of the SDI output connectors. For details on the positions of these connectors, refer to the figure below and to “Connector Area” (page E-1). CABLESHORT ALARMFUSEGENLOCK VTR ENABLE WHITE BAL REW Base Station AJ - FF STOP SHUTTER SET UP MON SEL KNEE POINT KNEE SLOPEGAMMADETAIL M.PED PLAY AW B CHECK AUTO IRIS IRIS B R GAINFILTER ABBBAR ENABLE PAINTING GAINAUTO KNEE GAIN REC CHKSTART / STOPCALL TA L LY VTR WARNINGON OFF (PUSH) OFF SC HCOARSE INTERCOM PGM ON OFF PTTPREA BMIC PRIVATE SYSTEM PUSH PHASE HEAD POWER ON OFF MAIN ON OFF FUSE OPEN BLACKRG ENG SEQB SUPS.V S.S. 100(60)1000120 250500 2000 DIGITAL TRIAX
![](/img/blank.gif)
E - 3 Installation PUSH PUSH PUSH 7.10.While referring to the figure below, pass the other ends of the cables connected in step 5 from the bottom toward the front panel top. 8.Remove the screw from the front panel of the cover removed from the AJ-BS900, and disengage the metal piece shown in the figure below. (The screw cannot be removed from the metal piece.) 9.Connect the ends of the cables which were passed from the bottom in step 7 to the board so that they are aligned in the directions shown in the figure below.Insert the board into the left-most slot of the AJ-BS900, and reattach the metal piece, which was disengaged in step 8, to its original position. When securing the metal piece, ensure that the cables are not pinched. Screw Metal piece 11.Pull out the excess lengths of the cables toward the bottom, and anchor the cables using cable clamps so that no slack remains in the cables. 12.Return the front panel cover, bottom panel and side panels in this order to their original positions, and secure them using the respective screws. Cable clamps
![](/img/blank.gif)
E - 4 ENGLISH Specifications GENERAL Weight: 170 g Dimensions: 230 (W) x 113 (H) x 20 (D) mm VIDEO OUTPUT Serial digital output connectors: BNC x 2 SERIAL OUT 1: SDI output connector SERIAL OUT 2: SDI output connector SDI: Compliant with SMPTE 259M-C standard AUDIO OUTPUT Serial digital output connectors: Compliant with SMPTE 259M-C/SMPTE 272M-A standards Specifications
![](/img/blank.gif)
D - 1 Anschlussbereich (AJ-BS900) Serielle Digitalausgänge (BNC x 2) 1 Ausgang 1: SDI-Ausgang 2 Ausgang 2: SDI-Ausgang Y/G OP1 4:2:2 4:2:2 SDI OUT OUT OP4 OP3 WFM TALL YOP2 AUDIO OUT CH 1PUSHCH 2PUSHCATION PB/B PR/R WFM 2 SDI-Ausgang 1 SDI-Ausgang Übersicht/Anschlussbereich Übersicht AJ-YA901P/E Diese SDI-Ausgangsplatine ist für den Einsatz mit dem AJ-BS900 vorgesehen. Ihr Einbau in den AJ-BS900 ermöglicht die digitale Datenausgabe im SDI-Format. Überlassen Sie den Einbau der SDI-Ausgangsplatine qualifiziertem Wartungspersonal.
![](/img/blank.gif)
D - 2 DEUTSCH EXT DC IN GEN– LOCKENC1 ENC2 ENC3 PIX Y/G 4:2:2 4:2:2 SDI OUT OUT IN OP4 OP3 WFM TALLYFUSE SIGNAL GND AC IN AUDIO OUT CH 1PUSHCH 2PUSHCOMMUNICATION PB/B PR/R WFMRET 1 RET 2 PROMPT OP1 OP2 1. 2. 3.4. Installation CABLESHORT ALARMF U S E H E A D P O W E R O N O F F M A I N O N O F F F U S EOPENDIGITAL TRIAXG E N L O C KOFF SC HC O A R S E INTERCOMP G MON OFFP T TM I CP R I V A T ES Y S T E MP U S H P H A S EV TR E N A B L EREW FF STOP S H U T T E RS E T U P M O N S E L K N E E P O I N T K N E E S L O P E G A M M AD E T A I L M .PE D O N O FF (PUSH) RG E N G S E QB SU PS.V S.S 100(60)1000120 250500 2000W H IT E B A L PLAY AWB C H E C KA U T O I R I S I R I SB RG A I NFILTER A B BB A R ENABLEPAINTING G A I NAUTO KNEE G A I N R E C C H KS T AR T / S T OPCALLTALLYVTR WARNINGPREA B B L A C K B a s e S ta t i o nA J - Führen Sie die folgenden Schritte aus, um die Platine AJ-YA901 in den AJ-BS900 einzubauen. Die in der nachstehenden Abbildung gezeigten vier Schrauben von der Rückwand des AJ-BS900 entfernen. Je zwei Schrauben von der linken und rechten Seitenwand des AJ-BS900 entfernen, und die Seitenwände abnehmen. Zwei Schrauben von der Bodenplatte des AJ-BS900 entfernen, und die Bodenplatte abnehmen. 6.Die vier Schrauben von der Frontplatte des AJ-BS900 entfernen, und die Frontplattenabdeckung abziehen. (Die Schrauben können nicht von der Frontplattenabdeckung entfernt werden.) Die Enden der an der Platine angebrachten Kabel von der in der folgenden Abbildung gezeigten Position an der Unterseite zur Oberseite der Rückwand führen. Schrauben (x 4) Schrauben (x 2)Schrauben (x 4) Seitenwand Bodenplatte 5.Die in Schritt 4 in den AJ-BS900 eingeführten Kabel an der Innenseite der SDI-Ausgangsbuchsen anschließen. Einzelheiten zur Lage dieser Buchsen sind der folgenden Abbildung und dem Abschnitt “Anschlussbereich” (Seite D-1) zu entnehmen. CABLESHORT ALARMFUSEGENLOCK VTR ENABLE WHITE BAL REW Base Station AJ - FF STOP SHUTTER SET UP MON SEL KNEE POINT KNEE SLOPEGAMMADETAIL M.PED PLAY AW B CHECK AUTO IRIS IRIS B R GAINFILTER ABBBAR ENABLE PAINTING GAINAUTO KNEE GAIN REC CHKSTART / STOPCALL TA L LY VTR WARNINGON OFF (PUSH) OFF SC HCOARSE INTERCOM PGM ON OFF PTTPREA BMIC PRIVATE SYSTEM PUSH PHASE HEAD POWER ON OFF MAIN ON OFF FUSE OPEN BLACKRG ENG SEQB SUPS.V S.S. 100(60)1000120 250500 2000 DIGITAL TRIAX
![](/img/blank.gif)
D - 3 Installation PUSH PUSH PUSH 7.10.Die anderen Enden der in Schritt 5 angeschlossenen Kabel gemäß der folgenden Abbildung von der Unterseite zur Oberseite der Frontplatte führen. 8.Die markierte Schraube von der freigelegten Vorderseite des AJ-BS900 entfernen, und die in der folgenden Abbildung gezeigte Metallplatte abnehmen. (Die Schraube kann nicht von der Metallplatte entfernt werden.) 9.Die Enden der in Schritt 7 von der Unterseite eingeführten Kabel so an die Platine anschließen, dass die Kabel gemäß der folgenden Abbildung verlaufen.Die Platine in den äußersten linken Steckplatz des AJ- BS900 einführen, und die in Schritt 8 abgenommene Metallplatte wieder an ihrem ursprünglichen Platz anbringen. Beim Befestigen der Metallplatte darauf achten, dass die Kabel nicht eingeklemmt werden. Schraube Metallplatte 11.Die überschüssigen Kabellängen nach unten ziehen, und die Kabel mit den Kabelklemmen so verankern, dass sie keinen Durchhang haben. 12.Frontplattenabdeckung, Bodenplatte und Seitenwände in dieser Reihenfolge wieder anbringen und mit den jeweiligen Schrauben befestigen. Kabelklemmen
![](/img/blank.gif)
D - 4 DEUTSCH Technische Daten ALLGEMEINES Gewicht: 170 g Abmessungen: 230 (B) x 113 (H) x 20 (T) mm VIDEO-AUSGÄNGE Serielle Digitalausgänge: BNC x 2 SERIAL OUT 1: SDI-Ausgang SERIAL OUT 2: SDI-Ausgang SDI: Entspricht der Norm SMPTE 259M-C AUDIO-AUSGANG Serieller Digitalausgang: Entspricht den Normen SMPTE 259M-C/SMPTE 272M-A Technische Daten
![](/img/blank.gif)
F - 1 Section des connecteurs (AJ-BS900) Connecteurs de sortie numérique série (BNC x2) 1 Sortie 1 : Sortie SDI 2 Sortie 2 : Sortie SDI Y/G OP1 4:2:2 4:2:2 SDI OUT OUT OP4 OP3 WFM TALL YOP2 AUDIO OUT CH 1PUSHCH 2PUSHCATION PB/B PR/R WFM 2 Sortie SDI 1 Sortie SDI Vue d’ensemble AJ-YA901P/E La carte de sortie SDI a été conçue pour l’AJ-BS900. Son installation dans l’AJ-BS900 permet l’envoi des données numériques à l’aide du format SDI. Vue d’ensemble/Section des connecteurs Confier l’installation de la carte de sortie SDI à un personnel qualifié.