Panasonic Aj Sd755 Operating Instructions Manual

							41
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
320
VAR FWD
MAXThis sets the maximum SLOW FWD speed.
0000+4.1:+4.1 (+3.1)aspeed0001 +1.85:+1.85aspeed0002 +1:+1aspeed

OThe value for the DV/DVCAM tape is shown in
parenthesis (    ).
OAt any speed setting other than +4.1, the
phase cannot be synchronized from the editing
controller.
323
JOG FWD
MAXThis sets the maximum JOG FWD speed.
0000 +4.1:+4.1 (+3.1)aspeed0001 +1.85:+1.85aspeed0002+1:+1aspeed

OThe value for the DV/DVCAM tape is shown in
parenthesis (    ).
OThe maximum speed is set to +1awhen the
dial on the front panel is operated.
OAt any speed setting other than +4.1, the
phase cannot be synchronized from an editing
controller which synchronizes the phase using
the JOG command.
324
JOG REV MAXThis sets the maximum JOG REV speed.
0000–4.1:–4.1 (–3.1)aspeed0001–1.85:–1.85aspeed0002–1:–1aspeed0003–0.43:–0.43 (–0.5)aspeed

OThe value for the DV/DVCAM tape is shown in
parenthesis (    ).
OThe maximum speed is set to –1awhen the
dial on the front panel is operated.
325
POSTROLL
TMThis sets the postroll time.
Any time from 0 to 5 seconds can be set in 1-
second units.
0000 0s
0001 1s
0002
2s0003 3s
0004 4s
0005 5s
321
VAR REV MAXThis sets the maximum SLOW REV speed.
0000–4.1:–4.1 (–3.1)aspeed0001–1.85:–1.85aspeed0002–1:–1aspeed
0003–0.43:–0.43aspeed

The value for the DV/DVCAM tape is shown in
parenthesis (    ).No./Item Description
311
AUD EDIT INThis selects the connection method for the
digital audio edit IN point.
0000 CUT:Cut processing0001FADE:V Fade processing
312
AUD EDIT
OUTThis selects the connection method for the
digital audio edit OUT point.
0000 CUT:Cut processing0001FADE:V Fade processing
313
AUTO ENTRYThis selects whether the IN point is to be
entered using the PREROLL button when it
has not been entered.
0000DIS:IN point is not entered.0001 ENA:IN point is entered.
314
CF ADJ SELThis selects the CF adjustment deck with
deck-to-deck editing.
0000PLAYER:
The player’s edit IN/OUT points are adjusted.
(reference as the RECORDER side)
0001 RECORD:
The recorder’s edit IN/OUT points are
adjusted. (reference as the PLAYER side)
315
AFTER 
CUE-UPThis selects the mode after cue-up operation
is complete.
0000STOP:STOP mode0001 STILL:SHTL STILL mode0002 STILL2:SLOW STILL mode 
						

							42
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
400
STILL TIMERThis menu item is for selecting the time to
elapse before the tape protection mode is
established when a DVCPRO tape is used.
It is also for selecting the time to elapse before
the tape protection mode is established when the
VTR has been left standing in the STOP or
search STILL (JOG, SLOW or SHTL) mode.
(Unit: s = second, min = minute)
0000 0.5s
0001 5s
0002 10s
0003 20s
0004 30s
0005 40s
0006 50s
0007 1min
0008
2min
401
SRC
PROTECTWhen the time selected as the setup menu
item No. 400 (STILL TIMER) setting elapses
while the unit is in the search STILL
(JOG/SLOW/SHTL) mode, the unit
automatically enters one of the tape
protection modes. This menu item is for
selecting which tape protection mode the unit
is to enter.
0000STEP:STEP FWD0001 HALF:HALF LOADING

When STEP FWD is selected, the unit
automatically goes into the STANDBY OFF
(HALF LOADING) mode when the total time for
which the unit is left standing in the still status
reaches 30 minutes (or 1 minute for a
DV/DVCAM tape).
402
DRUM STDBYThis selects the drum operation in the
STANDBY OFF (HALF LOADING) mode.
0000 OFF:The drum stops rotating.0001ON:The drum continues rotating.
OSTEP FWD and HALF
LOADING are provided in the
tape protection mode. Either
of these can be set for STOP
and SEARCH STILL.
OThe cumulative standby time
at the same tape position
increases when transmitting
programs or otherwise using
identical materials
repeatedly.
In order to protect the tape, it
is recommended that the
shortest possible setting for
the standby time in the same
tape location is used.No./Item Description
403
STOP
PROTECTWhen the time selected as the setup menu
item No. 400 (STILL TIMER) setting elapses
while the unit is in the STOP mode, the unit
automatically enters one of the tape
protection modes. This menu item is for
selecting which tape protection mode the unit
is to enter.
0000 STEP:STEP FWD0001HALF:HALF LOADING

When STEP FWD is selected, the unit is
automatically transferred to the STANDBY OFF
(HALF LOADING) mode when the total time
during which it has been left standing in the
STOP mode reaches 30 minutes (or 1 minute for
a DV/DVCAM tape).
404
DV STILL TMRThis menu item is for selecting the time to
elapse before the tape protection mode is
established when a DV or DVCAM tape is
being used.
It is for selecting the time to elapse before the
tape protection mode is established when the
VTR has been left standing in the STOP or
search STILL (JOG, SLOW or SHTL) mode.
(Unit: s = second, min = minute)
0000 0.5s
0001 5s
0002
10s0003 20s

When using the unit in tempuratures below 59°F
(15°C), set this item to 10 seconds to protect the
tape and video heads. 
						

							43
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
506
BINARY GPThis sets the usage status of the user bit of
the time code generated by the TCG.
0000000:
NOT SPECIFIED (character set not specified)
0001 001:
ISO CHARACTER (8 bits character set based
on ISO646, ISO2022)
0002 010:UNASSIGNED 1 (undefined)0003 011:UNASSIGNED 2 (undefined)0004 100:UNASSIGNED 3 (undefined)0005 101:PAGE/LINE0006 110:UNASSIGNED 4 (undefined)0007 111:UNASSIGNED 5 (undefined)
507
PHASE CORRThis selects whether to control the phase
correction of the LTC which is output from
the TIME CODE OUT connector.
0000OFF:
Phase correction control is not performed.
0001 ON:
Phase correction control is performed.
508
TCG CF FLAGThis selects whether the CF flag of the TCG is
to ON.
0000OFF:CF flag is OFF.0001 ON:CF flag is ON.
509
DF MODEThis selects the DF or NDF mode for CTL and
TCG.
0000DF:The drop frame mode is used.0001 NDF:The non-drop frame mode is
used.

Drop frame mode is valid only when the
CONTROL switch is set to LOCAL or the setup
menu No. 001 (LOCAL ENA) is set to ENA.
510
TC OUT REFThis is used to switch the phase of the time
code, which is output from the TIME CODE
OUT connector, for the external LTC input
when the TCG switch is at the EXT position.
0000VOUT:
Time code is synchronized with output video
signal.
0001 TC_IN:
Time code is synchronized with external time
code input. No./Item Description
500
VITC BLANKFor selecting whether to output the VITC
signal at the positions selected by setup
menu items No. 501 (VITC POS-1) and No. 502
(VITC POS-2).
0000 BLANK:VITC signals are not output.0001THRU:VITC signals are output.
501
VITC POS-1This sets the position where the VITC signal
is to be inserted.
0000 10L
::
0006
16L::
0010 20L

The same line as the one used for the setup
menu items No. 502 (VITC POS-2) and No. 662
(UMID POS) setting cannot be set.
503
TCG REGENThis selects the signal to be regenerated
when the time code generator (TCG) in the
REGEN mode.
0000TC&UB:
Both the time code and user bit are
regenerated.
0001 TC:
Only the time code is regenerated.
0002 UB:
Only the user bit is regenerated.
504
REGEN MODEThis selects whether the time code is to be
regenerated during automatic editing using
the unit’s control panel.
0000AS&IN:
Time code is regenerated with assemble or
insert editing.
0001 ASSEM:
Time code is regenerated with assemble
editing.
0002 INSRT:
Time code is regenerated with insert editing.
0003 SW:
Setting complies with TCG switch setting.505
EXT TC SELThis selects the time code to be used when
an external time code is to be used.
0000LTC:
The LTC of the TIME CODE IN connector is
used.
0001 VITC:
The VITC of the input video signal is used.
502
VITC POS-2This sets the position where the VITC signal
is to be inserted.
0000 10L
::
0008
18L::
0010 20L

The same line as the one used for the setup
menu items No. 501 (VITC POS-1) and No. 662
(UMID POS) setting cannot be set. 
						

							44
511
VITC OUTThis selects how the VITC which is to be
superimposed onto the output video signal is
to be output.
0000SBC:
During recording:
The input time code, which was selected by
the setup menu No. 505 (EXT TC SEL)
setting and TCG switch, is output as the
VITC.
During playback:
The time code recorded in the SBC area is
output as the VITC.
0001 VAUX:
During recording:
The time code detected from the input video
signal is output as the VITC.
During playback:
The time code recorded in the VAUX area is
output as the VITC.
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
514
VITC GENThis selects whether or not to record the
internal time code generator value in the
VAUX area.
0000OFF:
The internal time code generator value is not
recorded in the VAUX area.
When video signals on which the time code
has been recorded are input, the time code of
the input signals is recorded in the VAUX area.
0001 ON:
The internal time code generator value is
recorded in the VAUX area.

If SDTI/1394 has been selected as the input
signals using the INPUT SELECT button, the
time code on the input signals will be recorded
regardless of this menu’s setting. No./Item Description
512
TC OUT ADVThis selects how the phase alignment for the
time code output from the TIME CODE OUT
connector is to be handled.
Usually, it is aligned with the output video and
audio signals.
However, when external components are to be
connected, it is possible to align the phase with
the input signal.
0000OFF:
Phase alignment is not performed. 
The time code output from the TIME CODE
OUT connector is aligned with the output video
and audio signals.
0001 EDIT:
When editing mode has been selected, the
time code output from the TIME CODE OUT
connector is aligned with the input video and
audio signals during playback and editing
operations. 
In all other modes it is aligned with the output
video and audio signals.
513
RUN MODEThis sets the operation mode which is to
make the internal time code generator
advance.
0000REC:
The internal time code generator is advanced
during recording.
0001 FREE:
When the power is on, the internal time code
generator is advanced regardless of the
operation mode.SBC (sub code data) area:
This area is separate from the video and audio data area on the
helical track. The time code complying with SMPTE/EBU standards
is stored here. As with the conventional LTC (linear time code), the
time code can be read even during rewinding or fast forwarding. It
can also be read out when the tape has stopped.
VAUX (video auxiliary data) area:
This area is to be found in the video data area on the helical track.
The additional information relating to the video data is stored here.

The time code and user’s bit are controlled during tape playback by
the data which has been recorded in the SBC area. This means that
all the data recorded in the SBC area alone is used as the data
which is to be indicated on the counter display section in the middle
of the front panel or in the superimposed display, or as the data
which is to be transmitted to the editing controller or other unit. 
						

							45
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
600
INT SGThis selects the internal reference signal.
0001 BB:
The black burst is generated.
0002 CB100:
100% color bars are generated.
0003CB75:
75% color bars are generated.
601
OUT VSYNCThis selects whether to float the vertical sync
position of the video output in order to align
the video output phase with the input in the
EE/record/edit modes.
0000N-VF:Signals are not floated.0001 VF:Signals are floated.
602
V-MUTE SELThis selects whether to mute the video output
signals when a blank on the tape has been
detected during playback.
0000 N-MUTE:No muting. (Freeze)0001LOW RF:Muting. (Set to gray.)
603
CC (F1)
BLANKThis selects ON or OFF for the closed caption
signal of the first field.
0000 BLANK:Signal is forcibly blanked.0001THRU:Signal is not blanked.
604
CC (F2)
BLANKThis selects ON or OFF for the closed caption
signal of the second field.
0000 BLANK:Signal is forcibly blanked.0001THRU:Signal is not blanked.
606
OUT C KILLThis selects chroma color killer processing
for the video output signals.
0000 B/W:No color signals are output.0001COLOR:Color signals are output.
609
EDHThis selects whether to superimpose EDH
onto the SDI output signals.
0000 OFF:EDH is not superimposed.0001ON:EDH is superimposed.

OEven when ON is selected for this setting, EDH
is not superimposed onto the signals output
from the SDI OUT 3 connector if the SUPER
switch on the front panel of the unit is set to
ON.
OWhen no optional board (AJ-YA755G) has
been installed, setup menu No. 609 is not
displayed.610
P
B/PRIN LVThis selects the analog component input
level.0000 M II:M IIlevel0001B-CAM:ß-CAM level
614
P
B/PROUT LVThis selects the analog component output
level.0000 M II:M IIlevel0001B-CAM:ß-CAM level
611
YC SEP MODEThis selects Y/C separation processing for
the composite input signals.
0000 B/W:
The signals are processed as B/W signals.
0001AUTO:
The signals are automatically detected.
618
INTERPOLATE
This selects the interpolation operation.
Vertical interpolation is conducted automatically
during slow-motion playback to reduce the
vertical movement of the playback pictures.
However, this menu item enables the
interpolation operation to be forcibly turned off.
0000 OFF:
Interpolation is forcibly turned off.
0001AUTO:
Interpolation is automatically turned on during
slow-motion playback.
605
FREEZE SELThis selects the freeze mode for still pictures.
0000FIELD:Field freeze.0001 FRAME:Frame freeze.

When frame freeze has been selected, the frame
slow status is established with the slow setting.
621
CCR MODEThis selects the cross color processing
during playback.
0000 OFF:
The cross color is output with no changes
made.
0001 ON:
The cross color can be reduced.
620
ESR MODEThis selects the operation mode for edge
subcarrier reduction (ESR) in the playback
circuit.
0000 OFF:
The mode is forcibly set to OFF.
0001AUTO:
The mode is automatically set to ON or OFF
depending on the VTR operation. 
						

							46
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
622
SETUPFor setting 7.5% setup processing to be
performed on input and output signals.
When the STOP button is pressed, operation is
transferred to the sub-screen, and the setup level
is set for each output. To return from the sub-
screen, press the STOP button again.
00
CMPST IN Sub-screen
This selects the 7.5% setup processing for
the input composite signal.
0000 THRU:
The signal is recorded in its original form.
0001CUT:
The signal is recorded with the 7.5% setup
removed.
02
CMPNT INThis selects the 7.5% setup processing for
the input component signal.
0000THRU:
The signal is recorded in its original form.
0001 CUT:
The signal is recorded with the 7.5% setup
removed.
03
CMPNT OUTThis selects the 7.5% setup processing for
the output composite, component and serial
(digital) signal.
0000THRU:
The signal is output in its original form.
0001 CUT:
The signal is output with the 7.5% setup
removed.
0002 ADD:
The signal is output with the 7.5% setup
added. 01
CMPST OUTThis selects the 7.5% setup processing for
the output composite signal.
0000 THRU:
The signal is output in its original form.
0001ADD:
The signal is output with the 7.5% setup
added.

Bear in mind the setting for sub-screen item No.
03 (CMPNT OUT) of setup menu item No. 622
(SETUP 25).
No./Item Description
624
CC RECFor selecting whether to record the closed
caption signals multiplexed on the input
signals on the tape.
0000OFF:
No closed caption signal is recorded.
In addition, the EE output signals are blanked.
0001 ON:
When a closed caption signal is detected from
the selected input signal, it can be recorded.

If SDTI/1394 signals have been selected as the
input signals, the closed caption signals which
have been multiplexed onto the input signals will
be recorded on the tape regardless of the setting.
660
UMID RECThis selects whether or not to record the
UMID information on the tape.
0000 OFF:
UMID information is not recorded on the tape.
In addition, EE output signals are blanked.
0001ON:
UMID information is recorded on the tape.

OIf SDTI/1394 has been selected as the input
signals using the INPUT SELECT button, the
UMID information on the input signals will be
recorded regardless of this menu’s setting.
OIf THRU has been selected as the setup menu
item No. 106 (EE MODE SEL) setting, UMID
information of the EE output signals will be
blanked.
645
WIDE SELECTThis selects whether or not to record the
wide-screen information on the tape.
0001 WIDE:
The wide-screen information is not recorded on
the tape.
0002NORMAL:
The wide-screen information is recorded on the
tape.

If SDTI/1394 has been selected as the input
signals using the INPUT SELECT button, the
wide-screen information on the input signals will
be recorded regardless of this menu’s setting. 
						

							47
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
661
UMID GENThis selects the basic UMID information to be
recorded on the tape when ON has been
selected as the setup menu item No. 660
(UMID REC) setting.
0000 INT:
Newly created basic UMID information of this
unit is always recorded.
0001EXT:
The basic UMID information of the input
signals is recorded.
Newly created basic UMID information of this
unit is recorded if there is no basic UMID
information on the input signals.

The source pack (of the UMID information) of the
input signal will be recorded on the tape,
regardless of this menu’s setting.
662
UMID POSThis sets the line on which the UMID
information is to be superimposed.
0000 BLANK
0001 12L
::
0006
17L::
0008 19L

The line selected for the setup menu item No.
501 (VITC POS-1) and No. 502 (VITC POS-2)
settings cannot be selected for this item. 
						

							48
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
701
CH1 IN LVThis selects the audio input (CH1) reference
level switching.
0000 4dB
00010dB0002–20dB
702
CH2 IN LVThis selects the audio input (CH2) reference
level switching.
0000 4dB
00010dB0002–20dB
706
CH1 OUT LVThis selects the audio output (CH1) reference
level switching.
0000 4dB
0001
0dB0002–20dB
707
CH2 OUT LVThis selects the audio output (CH2) reference
level switching.
0000 4dB
00010dB0002–20dB
711
MONIL OUT
LVThis selects the audio monitor output (Lch)
reference level switching.
0000 4dB
00010dB0002–20dB
712
MONIR OUT
LVThis selects the audio monitor output (Rch)
reference level switching.
0000 4dB
00010dB0002–20dB
715
CH1 IN SELThis selects the CH1 input when USER SET
has been selected by pressing the unit’s
AUDIO input selector button.
0000ANA:Analog input.0001 DIGI:Digital input.
716
CH2 IN SELThis selects the CH2 input when USER SET
has been selected by pressing the unit’s
AUDIO input selector button.
0000ANA:Analog input.
0001 DIGI:Digital input.719
DIGI IN SEL
This selects the CH1 and CH2 digital input
when USER SET has been selected by pressing
the unit’s AUDIO input selector button.
0000AES:AES/EBU input0001 SIF:SDI input

When no optional board (AJ-YA755G) has been
installed, setup menu No. 719 is not displayed.
713
MONI OUTThis selects whether or not to couple the
volume level of the audio monitor output with
the volume control of the headphone jack.
0000 UNITY:
Volume is output at a fixed level, regardless of
the position of the volume control.
0001VAR:
Audio monitor output volume is coupled to the
volume control.
721
MONI CH SELThis selects  the monitor output.
0000 MANU:
The output signal is as selected in MONITOR
SELECT buttons.
0001AUTO:
PCM AUDIO output is selected within the
–0.43 (–0.5)ato +1aspeed range; CUE is
automatically selected for all other tape
speeds.

The value for the DV/DVCAM tape is shown in
parenthesis (    ).
0002 PCM:
The PCM AUDIO signal is output over the
–10ato +10arange.

This setup menu’s setting takes effect when CH1
or CH2 has been selected by the L and R
MONITOR SELECT buttons on the front panel. (If
CUE has been selected, the cue signal will be
output at all the speeds regardless of the setup
menu’s setting.)
722
REC CH1This selects the input signal to be recorded
on the audio CH1 track.
0000CH1:Audio input CH1 signal.0001 CH2:Audio input CH2 signal.0002 CH1+2:Mixed audio input CH1 and CH2
signal.
723
REC CH2This selects the input signal to be recorded
on the audio CH2 track.
0000 CH1:Audio input CH1 signal.0001CH2:Audio input CH2 signal.0002 CH1+2:Mixed audio input CH1 and CH2
signal.
726
REC CUEThis selects the input signal recorded in CUE.
0001CH1:Audio CH1 input
0002 CH2:Audio CH2 input0003 CH1+2:Audio CH1 and CH2 MIX signal
727
PB FADEThis selects the processing method for the
audio edit points (IN point, OUT point) during
playback.
0000AUTO:According to the status during
recording.
0001 CUT:Forced CUT0002 FADE:Forced FADE 
						

							49

The table below shows how the CUE output to the monitor and main signal system outputs differs according
to how the setup menu item (No. 721, No. 731 and No. 735) settings are combined.
731
CUE OUT
SEL
OFFMANU
AUTO
PCM
MANU----------
L/R
L
R
----------
----------
L/R
L
R
----------PCM 
21PCM 21
CUE
CUECUE
PCM 
21
PCM 21
PCM 22
PCM 21
CUE
CUE
PCM 
21
CUE
PCM 
21
CUE
PCM 
22
CUE
PCM 
22
PCM 21
PCM 22
PCM 21
PCM 22PCM 22
PCM 21
CUE CUE PCM 
21PCM 21
CUE
PCM 21
PCM 21
PCM 22
CUE
PCM 
22
AUTO
PCM ON721
MONI CH
SEL735
MON AUTO
SELMonitor output Main signal system output
CH1 Lch Rch CH2

21:PCM audio signal output is muted when the VTR is played outside the –0.43 to +1 normal speed.
22:PCM audio signal output is muted when the VTR is played outside the –10 to +10 normal speed.
When either AUTO is selected, the PCM audio signal is output within –0.43 to +1 normal speed even in
the automatic CUE output mode.
No./Item Description
735
MON AUTO
SELAlthough CUE is automatically output to the
monitor output in accordance with the operation
mode when a setting AUTO has been selected by
setup menu item No. 721 (MONI CH SEL), the
MON AUTO SEL setup menu item is used to
select the monitor channel which is to be
automatically switched to CUE.
0000L/R:
CUE is output to both the left and right channels.
0001 L:
CUE is output to the left channel only.
0002 R:
CUE is output to the right channel only.
734
MONI SEL INHThis selects whether the operation of the
MONITOR SELECT button on the front panel is to
be enabled or disabled.
0000OFF:Operation is enabled.0001 ON:Operation is disabled.0002 ON1:
Operation is disabled in the FULL display mode
and enabled only in the FINE display mode.
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
728
EMBEDDED
AUDThis selects whether to superimpose the
audio data onto the SDI output.
0000 OFF:Data is not superimposed.0001ON:Data is superimposed.

When no optional board (AJ-YA755G) has been
installed, setup menu No. 728 is not displayed.
731
CUE OUT SELThis selects whether or not the cue signal is
to be output to the main line output in the
search mode.
0000OFF:CUE is not output.0001 ON:CUE is output.

OThis function works only when a setting
other than MANU has been selected by
setup menu No. 721 (MONI CH SEL).
OThe main signal system output channels
used for the CUE output differ depending on
the setting selected by setup menu No. 735
(MON AUTO SEL).
When L/R is selected:
CUE is output to CH1 and CH4.
When L is selected:
CUE is output to CH1.
When R is selected:
CUE is output to CH2.
OWhen PCM has been selected as the setup
menu No. 721 (MONI CH SEL) setting, PCM
is output.
733
CUE OUTThis selects the timing for the output picture and
CUE output when CUE has been selected for
monitor output.
0000NORMAL:The timing is aligned with the
output picture.
0001 DIRECT:Whatever has been recorded on
the tape is output with no delay.

When DIRECT has been selected, the timing of the
output picture and that of the cue output are not
aligned properly. 
						

							50
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
750
DV PB ATTThis selects the audio output level during DV
playback.
0000OFF:The audio output level is not
attenuated.
0001 ON:The audio output level is
attenuated (reduced).
751
REC PT MUTEThis selects whether to mute the sound where
recordings are joined during DV/DVCAM
playback.
0000OFF:The sound is not muted.0001 ON:The sound is muted.
753
REF LEVELFor setting the audio reference level.
0000FS-20:–20 dB0000 FS-18:–18 dB0000 FS-12:–12 dB
752
DV OUTPUTThis selects the AUDIO CH1 and CH2 output
signals during DV or DVCAM format playback.
0000ST1:
The CH1 track signals are output to CH1 and
the CH2 track signals to CH2. (Only the sound
during shooting is output.)
0001 ST2:
The CH3 track signals are output to CH1 and
the CH4 track signals to CH2. (Only the audio
dubbing sound is output.)
0002 ST1+2:
The mixed CH1 and CH3 track signals are
output to CH1 and the mixed CH2 and CH4
track signals to CH2. (The sound during
shooting and audio dubbing sound are output
simultaneously.)

This menu item takes effect only when a DV or
DVCAM cassette tape with a 32 kHz/4-channel
recording is played back.