Panasonic Aj Sd755 Operating Instructions Manual
Have a look at the manual Panasonic Aj Sd755 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 Automatic editing (deck-to-deck) 1Select the editing mode. For assemble editing, press the ASSEM button. For insert editing, press the INSERT button. ASSEM: This sets the unit to assemble (frame-to-frame continuity) editing mode. INSERT: This sets the unit to insert editing mode. 2Select the channels to be edited. With assemble editing, the ASSEM lamp lights. With insert editing, press the buttons corresponding to the channels to be edited so that their lamps light. 3Select the VTR to be operated. (Settings for editing using two VTRs) Press the PLAYER or RECORDER button to select the VTR which is to be operated. PLAYER: Press this button if the player VTR is to be operated to register the edit points. RECORDER: Press this button if the recorder VTR (this unit) is to be operated to register the edit points. Selecting the editing mode 1Locate the edit IN point by performing the jog or shuttle operation. Set the tape to the still picture mode at the desired position. For a detailed description of the jog and shuttle operations, refer to page 18. 2Press the SET button while holding down the IN button. The edit IN point is now registered. The edit IN point value appears on the display panel. 4Press the SET button while holding down the OUT button. The edit OUT point is now registered. The edit OUT point value appears on the display panel. 3Locate the edit OUT point by performing the jog or shuttle operation. Set the tape to the still picture mode at the desired position. Registering the edit points Match frame processing function When two VTRs are used to perform the editing operations, there will be a total of 4 edit points: the IN and OUT points for the player and those for the recorder. However, the last point is automatically calculated so only three of the edit points need to be registered. ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 1/23 ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 2/41/3
22 Automatic editing (deck-to-deck) 1Press the IN (or OUT) button to check the edit point. The value of the registered edit point appears on the display panel. 2While holding down the IN (or OUT) button, press the PREROLL button and check the picture at the edit point. The tape is cued up to the edit IN (or OUT) point, and a still picture of the point appears. OIf STOP has been selected as the setup menu No. 315 (AFTER CUE-UP) setting or if the MODE switch has been set to EE, the VTR is set to the E-E mode. 3By holding down the IN and OUT buttons at the same time, check the editing duration. The duration appears on the display panel. How to calculate the duration OWhen two edit points have been set: Duration between the two points OWhen only one edit point has been set: Duration between the data which has been set and the current address OWhen no edit points have been set: Duration of the previously edited section 4After the edit points have been registered, press the PREVIEW button. Regular preview is now conducted. OIf the edit IN point has not been registered, the position where the PREVIEW button was pressed is registered as the edit IN point. OTo stop the preview at any time, press the STOP button. OWhen the PREVIEW button is pressed again after the IN point during the course of a preview, the preview will start again from the beginning. OWhen the edit OUT point is reached, the tape stops automatically. Checking and previewing edit points ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 41/32
23 Automatic editing (deck-to-deck) 1Re-registering an edit point Locate the new edit point by performing the jog or shuttle operation, and press the IN (or OUT) button and SET button at the same time to re-register the edit point. 2Modifying an edit point in 1-frame increments (trimming function) Press the TRIM button while holding down the IN (or OUT) button. Each time the + button is pressed, the point is moved ahead by one frame. Conversely, each time the – button is pressed, the point is moved back by one frame. 3Resetting edit points OResetting both an edit IN point and OUT point Press the RESET button. (This takes effect only in the CTL mode.) OResetting either an edit IN point or OUT point Press the RESET button while holding down the IN (or OUT) button. OAn edit OUT point can be reset even while editing is in progress. OIn the eject mode, the IN and OUT points are automatically reset. Modifying edit points ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 123
24 2Upon completion of the editing, press the REVIEW button. Review is then started by the recorder side. OTo stop the review at any time, press the STOP button. OWhen the edit OUT point is reached, the tape is post-rolled, after which it stops.1Press the AUTO EDIT button. Automatic editing is now executed. OTo suspend editing at any time, press the STOP button. OWhen the edit OUT point is reached, the tape is post-rolled, after which it stops. Post-rolling With assemble editing, editing continues for about 2 seconds after the edit OUT point is passed, the tape is then returned to the OUT point, after which it stops. With insert editing, the PLAY mode is established after the edit OUT point has been passed, the tape is then returned to the OUT point, after which it stops. The post-roll time can be set using setup menu No. 325 (POSTROLL TM). Retry function Even when the STOP button has been pressed to suspend editing, editing can be repeated from the beginning simply by pressing the AUTO EDIT button again. Auto tag function (recorder side) If, upon completion of editing, the next edit point has not yet been registered, the previous edit OUT point is registered as the IN point and editing is executed when the AUTO EDIT button is pressed. To release the auto tag mode, press one of the transport system buttons (such as the PLAY button). Registering an OUT point while editing is in progress If the SET button is pressed while the OUT button is being held down when automatic editing is in progress, the position corresponding to when the button was pressed is registered as the OUT point and the editing operation is exited. Even if the AUTO EDIT button is pressed, the OUT point is registered and editing is exited in the same way. The registered points are automatically cleared after editing has been executed. However, the previous edit points can be recalled by pressing the TRIM+ (or TRIM–) button and SET button at the same time. Executing and reviewing automatic editing ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 12 Automatic editing (deck-to-deck)
25 $Displaying the audio split edit points The edit points appear on the display panel. Video IN point: Press the IN button. Video OUT point: Press the OUT button. Audio IN point: Press the A IN button. Audio OUT point: Press the A OUT button. If the editing mode is changed to assemble editing after the audio edit points have been registered, the audio edit points will be cleared. $Cueing the tape up to the edit points Cue-up to video IN point: Press the PREROLL button while holding down the IN button. Cue-up to video OUT point: Press the PREROLL button while holding down the OUT button. Cue-up to audio IN point: Press the PREROLL button while holding down the A IN button. Cue-up to audio OUT point: Press the PREROLL button while holding down the A OUT button. The video edit points and audio edit points can be registered independently, and editing can be executed with the video point offset from the audio points. Audio edit points cannot be registered when the assemble editing mode has been selected. After registering the edit points, proceed with the same operations as for insert editing. $Registering the edit points Video IN point: Press the SET button while holding down the IN button. Video OUT point: Press the SET button while holding down the OUT button. Audio IN point: Press the SET button while holding down the A IN button. Audio OUT point: Press the SET button while holding down the A OUT button. $Clearing the edit points Video IN point: Press the RESET button while holding down the IN button. Video OUT point: Press the RESET button while holding down the OUT button. Audio IN point: Press the RESET button while holding down the A IN button. Audio OUT point: Press the RESET button while holding down the A OUT button. $Modifying edit points Video IN point: Press the TRIM+ button or TRIM– button while holding down the IN button. Video OUT point: Press the TRIM+ button or TRIM– button while holding down the OUT button. Audio IN point: Press the TRIM+ button or TRIM– button while holding down the A IN button. Audio OUT point: Press the TRIM+ button or TRIM– button while holding down the A OUT button. Audio split editing A IN button A OUT button ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL
26 Audio split editing $Duration display The duration can be indicated on the display panel only. Between the video IN and OUT points: Press the IN button and OUT button at the same time. Between the audio IN and OUT points: Press the A IN button and A OUT button at the same time. Match frame processing system When two VTRs are used to perform the audio split editing operations, there will be a total of 8 edit points: the video IN and OUT points for the player, the video IN and OUT points for the recorder, the audio IN and OUT points for the player, and the audio IN and OUT points for the recorder. When five of the eight edit points are registered, the remaining three points are automatically calculated so only five of the edit points need to be registered. $When a VTR not equipped with the split editing function is used as the player When a VTR that cannot set the video and audio edit points independently is used as the player, split editing is still possible by setting the audio IN point and OUT point in the recorder and setting the data of three points as the video edit points. If, during audio split editing, the video OUT point (or audio OUT point) only is registered without the audio OUT (or video OUT point) having been registered and automatic editing is then executed, either the audio OUT point (or video OUT point) will be registered or editing will continue until the STOP button is pressed to suspend the editing operation.
27 ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 8 95 4 4 4After selecting VTR used as the player by pressing PLAYER button, set the initial speed by the search dial while pressing SET button. 5Simultaneously pressing both SET button and PREVIEW/REVIEW button results in automatic prerolling for the both VTRs (player and recorder), then the player VTR is operated at the set initial speed up to the IN point. 6After passing the IN point, turn the search dial to memorize the playback speed of the VTR used as the player. 7When the tape has passed the OUT point set by recorder, the memory of the playback speed will terminate. 8When AUTO EDIT button is pressed, variable memory editing is executed. Once editing has been executed, the memorized speed will be cleared. The initial speed will not be cleared however. 9The result of editing can be checked by pressing PREVIEW/REVIEW button. OThe content stored in the memory will be cleared in a mode other than the variable memory mode. Also, the memory will be cleared when the power switch is turned OFF. OPhase adjustment is not made during playback to the IN point of variable memory editing. Therefore, depending on the VTR used as the player and its speed setting, no guarantees are made for the accuracy of the IN point. OWhen variable memory editing is to be performed, keep the speed set to within the speed range for variable speed playback which can be guarantied by the VTR used as the player. Using the unit as a controller (deck-to-deck editing mode recorder) to control the playback speed of the VTR used as the player, editing can be performed in speed variable mode. $Selecting the variable memory mode When deck-to-deck editing (either the RECORDER or PLAYER lamp lights) is to be performed, set the initial speed (–1.0 to +2.0) by turning the search dial with the SET button held down to transfer the unit to variable memory mode. $Releasing variable memory mode Press the RESET button while holding down the SET button to release the unit from variable memory mode. The unit will also be released from this mode when deck-to-deck editing operations are completed. Variable memory editing operation procedure Variable memory editing operation can be performed according to the following procedure. Variable memory editing ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 1 3 2 1Select the edit mode by pressing ASSEM button or desired INSERT buttons. 2Select VTR to be operated by pressing RECORDER or PLAYER button. 3Register IN/OUT point by using SET button and IN/OUT buttons. The OUT point of VTR used as the player cannot be registered.
28 4Upon completion of the setting, release the search button. The item number now flashes. OWhen the search dial is in the SHTL mode, the item will move unless the dial is set to the center position. 5When other items are to be changed, repeat steps 2to 4. 6Press the SET button. The changes are stored in the memory. To disregard the new settings and restore the old settings instead, press the MENU button. OTo return the setup contents to the factory settings (initial settings), press the RESET button while the menu is displayed. The following message is displayed. If the PLAY button is now pressed, the factory settings are reinstated. OIf the RESET button is pressed to restore the factory settings, only the user files currently in use are restored. The other user files remain unaffected. OThe changes made to the SYSTEM menu contents are recorded also by pressing the MENU button to close the menu screen. SETUP-MENU INIT SET YES/NO Setup (initial settings) 1Press the MENU button. The setup menu screen appears on the TV monitor, and the setup menu item number appears on the counter display. Each time the FF button is pressed (for about 1.5 seconds), the item number and item name are selected and displayed alternately. (If a setup was performed previously, the screen on which the last change was made is displayed.) 3At the position where the change is to be made, turn the search dial while holding down the search button. The settings on the menu screen and display now flash. When the dial is turned clockwise, the setting number is incremented; conversely, when it is turned counterclockwise, it is decremented. OAt this time, when the RESET button is pressed while holding down the search button, the setting value is returned to the factory setting. 2Turn the search dial to select the item to be set. The menu screen cursor (2) moves, and the item number on the display flashes. OWhen the dial is turned clockwise, the item number is incremented from 001 5002 5003 5004 and so on; conversely, when it is turned counterclockwise, the item number is decremented. OWhen the FF button or REW button is pressed while holding down the PLAY button, the next or previous item is selected. OWhenever possible, limit the use of the search dial to the JOG mode. This VTR’s main settings are performed while making selections using a system of menus. If a TV monitor has been connected to the VIDEO OUT 3 connector on the rear panel, the setup menus are displayed on the TV monitor. By installing the SDI board (AJ-YA755G, available as an optional accessory) in the VTR, it is possible to display the setup menus also on a TV monitor which has been connected to the SDI OUT 3 connector. Changing the settings ON OFFPOWERDVDVCPRO METER L R FULL/FINE MONITOR SELECT HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1 REC AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON OFFUNITY VA RPB COUNTERRESET A IN TRIM SET OUT IN A OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY EDIT REW STOPPLAY REC PLAYER RECORDER FF JOGSHTLSLOW TAPE EEONREGENPRESETEXITOFFREMOTELOCAL 4 261 3 FF button
29
Setup menus
1Press the MENU button.
2When the FF button is pressed while holding down
the DIAG button, the next user file is selected;
conversely, when the REW button is pressed while
holding down the DIAG button, the previous user
file is selected.
3To enter the selection made in step 2for the user
file which is to be used, press the SET button.
The user file is changed and stored in the memory. This VTR can hold five user files, each of which has
its own specific menu settings, and one of these files
can be selected for use.
Changing the file
1Press the MENU button.
2Press the REW button or FF button while holding
down the DIAG button to select the file for which
the lock mode is to be set or released.
3Turn the search dial to move the cursor (2) on the
menu screen to No. 30 (MENU LOCK) for the
system file or to No. A03 (MENU LOCK) for a user
file.
4Turn the search dial while holding down the search
button to select whether the lock mode is to be set
or released.
To set the lock mode:
Set 0001 (ON) as the setting.
To release the lock mode:
Set 0000 (OFF) as the setting.
When the lock mode has been set, “LOCKED”
flashes on the menu screen. The counter display
stops flashing and remains lighted.
5Press the SET button.
The setting is stored in the memory. The lock mode can be set to protect the system file
and user file (USER2 to USER5) settings. Once the
lock mode is set, no further changes can be made to
the settings.
Setting and releasing the lock mode can be set for the
system file by using setup menu No. 30 (MENU
LOCK) and for the user files by using setup menu No.
A03 (MENU LOCK).
Setting and releasing the lock mode
SYSTEM
FF REW
USER 1
FF REW
USER 2
FF REW
USER 3
FF REW
USER 4
FF REW
USER 5
FF REW
User files
Each user file contains the
following items.
OBASIC
OOPERATION
OINTERFACE
OEDIT
OTAPE PROTECT
OTIME CODE
OVIDEO
OAUDIO
OV BLANK
OMENU
Since the SYSTEM menu items are not included in
user files 1 through 5, first select the user file and
switch to the SYSTEM file, and then set the SYSTEM
menu items.
OThe lock mode cannot be set for the USER1 file.
OOnce set to the lock mode, a file cannot be reset to
the factory settings even by pressing the RESET
button.
SETUP-MENU LOCKED
NO.000-0005
2000 P-ROLL TIME 5s
001 LOCAL ENA ST&EJ
002 TAPE TIMER ±12h
003 REMAIN SEL OFF
004 SETUP NUMBER OFF
005 METER SELECT CUE
006 SYNCHRONIZE ON
007 SUPER ON
008 DISPLAY SEL T&STA
30
Setup menus
1Press the MENU button.
2Press the REW button or FF button while holding
down the DIAG button to select the USER1 file.
4Turn the search dial while holding down the search
button to select the user file whose contents are to
be loaded into USER1.
6Press the PLAY button.
The settings of the user file selected in step
4are
loaded, and the USER1 menu display appears. If
the STOP button is pressed instead, the settings
are not changed, and the USER1 menu display
appears.
7Turn the search dial to move the cursor (2) on the
menu screen to a number other than No. A00
(LOAD) or No. A01 (SAVE).
8Press the SET button. The USER1 settings are
stored in the memory.
If the USER1 settings are not to be stored in the
memory, do not press the SET button but press the
MENU button instead.
5Press the SET button.
The following message appears on the menu
screen and counter display.
3Turn the search dial to move the cursor (2) on the
menu screen to No. A00 (LOAD). The contents of the USER2, USER3, USER4 or
USER5 file can be copied (loaded) into the USER1
file. Also, the contents of the USER1 file can be
copied (saved) into the USER2, USER3, USER4 or
USER5 file.
Loading user files
SETUP-MENU MENU
NO.A00-0000
804 BLANK LINE BLANK
2A00 LOAD USER2
A01 SAVE USER2
A02 P.ON LOAD OFF
END
SETUP-MENU LOAD
USER2
nUSER1 OK?
YES/NO
USER 1USER 2
USER 3
USER 4
USER 5
Load/save
Lock mode can be
set
Load/save
Lock mode can be
set
Load/save
Lock mode can be
set
Load/save
Lock mode can be
setMenu screen
Counter display
The number of the user file selected in step 4is
displayed at .