Panasonic Aj Sd755 Operating Instructions Manual

51
No./Item Description
802
TELETEXT
SELFor selecting the type of teletext signals to be
recorded.
0000 MOJI:MOJI system0001NABTS:NABTS system

VITC signals are often mistakenly detected as
teletext signals when the NABTS system has
been selected.
If this happens, select MANU as the setting for
setup menu No. 803 (TELETEXT DET), then
select the line for teletext signals.
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
800
ADD LINE
00
REC LINE1 Sub-screenFor...

52
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
803
TELETEXT
DET
00
REC LINE1
:
12
REC LINE13 Sub-screenFor selecting the method used to detect the
lines in which the teletext signals are to be
recorded.
0000OFF:
The teletext signals are not recorded.
0001 AUTO:
The teletext signals are automatically detected
and recorded.
0002 MANU:
The lines in which the teletext signals are to be
recorded are selected and set.

OThe number of lines in which the...

53
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
A00
LOADThis selects the user file whose contents will
be loaded into USER1.
0000USER2:The USER2 file contents are
loaded.
0001 USER3:The USER3 file contents are
loaded.
0002 USER4:The USER4 file contents are
loaded.
0003 USER5:The USER5 file contents are
loaded.

When the SET button is pressed after loading,
the setting will be stored in the memory. When
the MENU button is pressed, the setting will not
be...

54
Time code/user bit
Time code
The time code is used when the time code signal
generated by the time code generator (time code
signal generator) is to be recorded on the tape, its
values are to be read by the time code reader (time
code signal reader), and the absolute position of the
tape is to be displayed in increments of hours,
minutes, seconds and frames.
The time code is written in the sub-code area (data
area) of the helical track. This enables insert editing to
be conducted independently using...

55
Time code/user bit
Setting the external time code
1Set the VTR to stop mode.
3Set the TCG switch to EXT. (External time code
selection)
4The following settings can be selected with setup
menu No. 505 (EXT TC SEL).
LTC:
The LTC signal input to the TIME CODE IN
connector (XLR) on the rear panel is recorded
as TC.

LTC must be synchronized with the video signal.
VITC:
The VITC of the input video signal is recorded
as TC.
2Select “TC” using the COUNTER button.
Reproducing the time code/user bit
1Set the...

56
Display position
The position of the characters superimposed on the
display can be changed using setup menus No. 009
(CHARA H-POS) and No. 010 (CHARA V-POS).
Superimpose screen
The control signals, time code, etc. are displayed
using abbreviations.Characters displayed
The background of characters superimposed on the
display can be changed using setup menu No. 011
(CHARA TYPE).
TCR  
22: 
22: 
22: 
22
TV monitorT TC
CR
R  
2 22
2: : 
2 22
2: : 
2 22
2: : 
2 22
2
TV monitor
TCR  
22: 
22: 
22: 
22
TV...

57
Video output signals and servo reference signal
This section explains how the output signals and
servo reference signal are selected.
External synchronization of video
output signals
The video output signals are output in synchronization
with the REF VIDEO input signal or video input signal.
As shown in the figure below, this signal is selected in
accordance with the setup menu settings, VTR mode
and availability of the video input signal.
Synchronization is determined as follows depending
on the...

58
Video output signals and servo reference signal
Servo reference signal
The REF VIDEO input signal or video input signal is
selected as the servo reference signal.
As shown in the figure below, the signal is selected in
accordance with the setup menu settings, VTR mode
and availability of the video input signal.
Synchronization is determined as follows depending
on the availability of the REF VIDEO input signal
when “BB”, “CB100” or “CB75” has been selected as
the setup menu No. 600 (INT SG) setting....

59
Audio V fade function
When editing tapes, the edit point splicing selection
(setup menu No. 311 and 312) information is recorded
on the tape. This information is then sensed during
playback, and V fade or cut processing is
automatically performed for these sections. 
However, only when the playback fade selection (No.
727) is AUTO.

OWhen the playback fade selection (No. 727) is
CUT, cut processing is performed for all splices.
OWhen the playback fade selection (No. 727) is
FADE, V fade processing is...

60
Audio recording channel and monitor output selection
Audio recording channel
The audio recording channels are selected on the
AUDIO setup menu as shown below.
Recording
track
CH1Recording signal
CH1 input/CH2 input/CH1 input+CH2 input
CH2CH1 input/CH2 input/CH1 input+CH2 input
CUECH1 input/CH2 input/CH1 input+CH2 input
Monitor output channel
The monitor output channels are selected using the
MONITOR SELECT and MONITOR MIX button as
shown below.
Monitor
output
LOutput signal
CH1/CH2/CH1+CH2/CUE...