Panasonic Aj Sd755 Operating Instructions Manual

11
Display panel
1WIDE lamp
This lamp lights when 16:9 wide-screen information
is being recorded on a tape.
Recording of wide-screen information can be
selected on setup menu No. 645 (WIDE SELECT).
This lights lamps during tape playback when wide-
screen information has been recorded on the tape.
2REMOTE lamp
This lamp lights when the CONTROL switch has
been set to the REMOTE position.
3INPUT SELECT display area
The characters corresponding to the selected input
signals light. With all input signals...

12
9EDIT, EDIT REC, REC and REC INH lamps
EDIT:
This lights when an editing mode has been
selected.
EDIT REC:
This lights when the edit recording mode has
been established.
REC:
This lights when the recording mode has been
established.
REC INH:
This lights in the recording inhibit status (when
the REC INH switch at the bottom front panel is
set to ON or the cassette is in the accidental
erasure prevention status).
In this status, recording and editing are not
possible.
Whether the REC INH lamp is to...

13
Rear panel
1AC IN socket
Connect one end of the power cord supplied to this
socket and the other end to the power outlet.
2DIGITAL AUDIO IN and OUT connectors
These are the input and output connectors for
digital audio signals that comply with the AES/EBU
standards.

The digital audio signals which are to be input to
these connectors must be synchronized with the
video input signals. Otherwise, noise will be
generated in the audio output signals.
3ANALOG COMPONENT VIDEO IN connectors
The analog...

14
Rear panel
ANALOG COMPONENT VIDEO OUT connectors
The analog component video signals are output
through these connectors.
?ANALOG COMPOSITE VIDEO OUT connectors
The analog composite video signals are output
through these connectors.
The waveform monitor (WFM) signal can be output
from the VIDEO OUT 2 connector.
It can be selected using setup menu No. 00 (WFM
SEL).
Video signals containing superimposed information
can be output through the VIDEO OUT 3 connector.
Whether the superimposing is to be set ON...

PUSH PUSH PUSHAC IN
SIGNAL
GND
AES/EBU ANALOGCH1/2
IN
YVIDEO
VIDEO
OUT
SERVICE ONLY
REMOTE IN/OUTCH1 CH2AUDIO
IN
ENCODER REMOTE
RS-232C
PARALLEL
REMOTE OUT
IN
REF VIDEOIN
ON
OFF
P
B
P
R
Y1
2
(WFM)
3(SUPER)
P
B
P
R
CH1/2
OUT
REMOTE
75Ω
ON
OFF75Ω
ANALOGTCIN
TCOUT
MON
L
MON
R
CH1 CH2AUDIO
OUTOPTION 2
OPTION 1
SDTIIN OUT
1
2
SDIIN OUT
ACTIVE
THROUGH1
2
3(SUPER)
PUSH PUSH PUSHAC IN
SIGNAL
GND
AES/EBU ANALOGCH1/2
IN
YVIDEO
VIDEO
OUT
SERVICE ONLY
REMOTE IN/OUTCH1 CH2AUDIO
IN
ENCODER REMOTE
RS-232C
PARALLEL...

16
Connections with editing controller
Connections
ON
OFFPOWERDVDVCPRO
METER
L
R FULL/FINEMONITOR SELECT
HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1REC
AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON
OFFUNITY
VA RPB
COUNTERRESET
A  INTRIM
SETOUT INA  OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BYEDIT
REW STOPPLAY REC PLAYERRECORDER
FF
JOGSHTLSLOW
TAPE
EEONREGENPRESETEXITOFFREMOTELOCAL
ON
OFFPOWERDVDVCPRO
METER
L
R FULL/FINEMONITOR SELECT
HEADPHONESMONITOR...

17
ON
OFFPOWERDVDVCPRO
METER
L
R FULL/FINE
MONITOR SELECT
HEADPHONESMONITOR MIXINPUT SELECTPREVIEW/PREVIEWAUTO EDITPREROLLVIDEOCH1
REC
AUDIOCH2 CH1 CH2TCPRESETMENU SET DIAGSUPER REC INHINT TCGMODECONTROLON
OFFUNITY
VA RPB
COUNTERRESET
A  IN
TRIM
SET
OUT IN
A  OUTCH2 CH1INSERTASSEMVIDEO CUE TCSTAND BY
EDIT
REW STOPPLAY REC PLAYER
RECORDER
FF
JOGSHTLSLOW
TAPE
EEONREGENPRESETEXITOFFREMOTELOCAL
L cassette size
Consumer-use DV and DVCAM cassettes
(Standard DV and DVCAM cassettes, mini DV and
DVCAM cassettes)...

18
Jog mode
Jog/Shuttle
1Press the search dial so that it remains pressed in.
Check that the JOG lamp has lighted.
Shuttle mode
1Press the search dial so that it is released from the
pressed-in position.
The SHTL lamp lights, and the shuttle mode is
established.
OImmediately after the power is turned on, turn
the search dial and leave it at the center
position.
3To transfer the VTR from the jog mode to another
mode, press the button that corresponds to the
mode concerned.
2Turn the search dial.
The...

19
Manual editing
1Select the editing mode.
ASSEMBLE:
Assemble (frame-to-frame continuity) editing is
performed in this mode.
INSERT:
Insert editing is performed in this mode.
2Select the channels to be edited.
For insert editing, press the buttons corresponding
to the channels to be edited so that their lamps
light.
3Press the PLAY button.
4While monitoring the TV monitor, search the
position (IN point) where the editing is to be
started, and press the PLAY and EDIT buttons
together at this position....

20
Automatic editing (deck-to-deck)
1Set the POWER switch to ON.
2Use the INPUT SELECT buttons to select the
video and audio input signals.
3Switch the time counter display to TC, CTL or UB.
4If the recording levels are to be adjusted using the
level controls, set the audio level control selector
switch to the VAR position.
If the recording levels are to be fixed, set the
switch to the UNITY position.
Audio recording level control knobsAudio playback level control knobs
5Set the CONTROL switch to LOCAL....