Panasonic Aj Hdc27fp Operating Instructions Manual

81
If the unit is in the rec-pause mode, it is possible to
ensure scene-to-scene continuity with an accuracy of
0 up to 1 frame just by pressing the VTR START
button or lens VTR button.
If the unit is in a mode other than rec-pause, the point
at which the scene-to-scene continuity is to be
maintained must be located before recording is
started.
Scene-to-scene continuity
The scene-to-scene continuity timing is located
automatically. However, the time taken until the start
of recording differs depending on...

82
When the PLAY/PAUSE button is pressed, the
playback pictures can be monitored in black and white
on the viewfinder screen.
These playback pictures can be monitored in two
other ways.
Rec review
When recording is temporarily stopped and the lens
RET button is pressed, the last two seconds of the
tape are automatically rewound, and the playback
pictures on this part of the tape appear on the
viewfinder screen.  This makes it possible to check
whether recording was performed properly.
After the two...

83
Other VTR functions
The NEWS REC function is set using NEWS REC
MODE on the VTR MENU “FUNCTION” screen.
By controlling the VTR START button
acknowledgment time during recording (by up to 2
seconds), the time taken for the unit to transfer from
the recording mode to the rec-pause mode can be
delayed.
In other words, by controlling the VTR start button
operation acknowledgment time, the unit can
continuously record without the user having to
interrupt the recording: this safeguards against the
failure...

84
Menu operations
The setting menu operations are performed using the
MENU button and JOG dial button.  The menu
configuration is divided into the camera unit’s setting
menus and VTR unit’s setting menus.
It is possible to select the engineer menu which
enables all the setting menu items to be set or,
alternatively, the user menu which consists of
individually tailored menus so that only those menus
which will be used most frequently can be set.

The engineer menu is displayed at all times when the...

85
Menu operations
User menu: Engineer menu
Basic setting menu operations
Displaying menus
FILM (CAM) 
USER MENU Press the MENU
button.Press the
MENU button.
Press the JOG
dial button.
1Press the MENU button.
The camera unit’s USER menu screen is
displayed.
2When the MENU button is pressed again, the VTR
unit’s USER menu screen is displayed.
1Hold down the MENU button for at least 3
seconds.
2When the JOG dial button is pressed, the next
MAIN menu screen (of the camera unit) is
displayed.
3When the MENU...

86
< ROP >
nMASTER PED      : +000
MASTER DTL      : +00
MASTER GAMMA    : 0.45
R GAIN          : +000
G GAIN          : +000
B GAIN          : +000
R PEDESTAL      : +000
G PEDESTAL      : +000
B PEDESTAL      : +000
Menu operations
Operations common to the user menu and
engineer menu
Example:
Displaying sub-menus and deciding
on settings
Turn the JOG
dial button.I
1Turn the JOG dial button while the USER menu
screen or MAIN menu screen is displayed.
The cursor (
n) moves to the SUB menu item.
2Move the...

87
Setting menu configuration
FILM (CAM) MAIN MENU 1
ROP
MATRIX
COLOR CORRECTION 1
COLOR CORRECTION 2
LOW SETTING
MID SETTING
HIGH SETTING
} ADDITIONAL DTL1
ADDITIONAL DTL2
   MASTER PED
   MASTER DTL
   MASTER GAMMA   R GAIN   G GAIN   B GAIN   R PEDESTAL   G PEDESTAL   B PEDESTAL
} MATRIX TABLE
   MATRIX R-G
   MATRIX R-B   MATRIX G-R   MATRIX G-B   MATRIX B-R   MATRIX B-G
R (SAT)/(PHASE)
Mg (SAT)/(PHASE)
B (SAT)/(PHASE)Cy (SAT)/(PHASE)G (SAT)/(PHASE)Yl (SAT)/(PHASE)
R-Mg (SAT)/(PHASE)
Mg-B...

88
Setting menu configuration
FILM (CAM) MAIN MENU 2
VF DIAPLSY
VF MARKER
VF INDICATOR
CAMERA ID
SHUTTER SPEED
! LED
CAMERA SW MODE
SUPER GAIN
DISP CONDITION
DISP MODE
VF OUTVF DTLZEBRA1 DETECTZEBRA2 DETECTZEBRA2LOW LIGHT LVLSYNCHRO SCAN DISP.ECU MENU DISP.
SAFETY ZONE
CENTER MARK
FRAME SIGMARKLVL
EXTENDER
SHUTTER
ID 2: 2222222222ID 3: 2222222222
FILTERWHITEGAINIRISCAMERA IDZOOM LVLCOLOR TEMPFRAME RATEVERSION ID (FILM MENU)
ID 1: 2222222222
SYNCHRO SCAN 1
POSITION 1SYNCHRO SCAN 2
POSITION 2POSITION...

89
Setting menu configuration
FILM (CAM) MAIN MENU 4
FILM (CAM) USER MENU SELECT1
FILM (CAM) USER MENU SELECT2
BLACK SHADING
FLARE
INITIALIZE
DIAGNOSTIC
OPTION
ROPLOW SETTINGMID SETTINGHIGH SETTINGADDITIONAL DTL1ADDITIONAL DTL2SKIN TONE DTLKNEE/LEVELGAMMACAMERA SETTING
VF DISPLAY
VF MARKER
VF INDICATOR!LEDCAMERA SW MODESUPER GAINFRAME MODE
FILM (CAM) USER MENU SELECT3CAM CARD READ/WRITE
CAM CARD R/W SELECT
GENLOCK/IRISDETECTION
CORRECT (DIG)
WHITE SHADINGDETECTION (V SAW)
CORRECT
R FLARE
G FLARE
B FLARE...

90
Setting menu configuration
VTR MAIN MENU
FUNCTION
BATTERY/TAPE
VTR VF INDICATOR
MIC/AUDIO
TIME/DATE
NEWS REC MODE
HUMID OPE
REC STARTPAUSE TIMERRETAKE MODEHD SDI OUTINTERVAL REC MODEINTERVAL REC TIMEINTERVAL PAUSE TIMEECU REC CHK SWCHARACTER ON SDI
BATTERY SELECT
EXT DC IN SELECT
BATT NEAR END ALARMBATT NEAR END CANCELBATT END ALARMBATT REMAIN FULLTAPE NEAR END ALARMTAPE NEAR END TIMETAPE END ALARMTAPE REMAIN/$BATTERY SETTINGAJ-BP490
AU-BP402...