Panasonic Aj Hdc27fp Operating Instructions Manual

71
How to use the scene file
11Turn the JOG dial button to move the arrow
(cursor) to YES, and press the JOG dial button.
The titles sare saved in the scene file area of the
camera’s memory.
12After the data has been saved, press the MENU
button twice.
The setting menu is cleared, and the displays
showing the unit’s current statuses appear at the
top and bottom of the viewfinder screen.
10When the JOG dial button is pressed, the
following message appears.
< CAM CARD READ/WRITE >
READ
SELECT      :1...

72
Use of the setup memory card (optional accessory)
enables the setting menu contents to be saved.  Use
of this data speeds up the process of reproducing
suitable setup statuses.
OThe multimedia cards or the SD memory cards can
be used as the setup cards.How to eject the setup card
Open the cover by raising its bottom edge, and eject
the setup card.

Take care not to touch the connector on the edge of
the setup card directly.
How to insert the setup card
With the surface bearing the logo facing you,...

73
If one of the following messages appears when the JOG dial
button is pressed, the card will not be formatted.
5Press the MENU button to exit the menu
operations.
The setting menu is cleared, and the displays
showing the unit’s current statuses appear at the
top and bottom of the viewfinder screen.
Error messageRemedial action
CONFIG NG
NO CARD
(setup card has not been
inserted)Insert the card.
CONFIG NG
ERROR
(the card cannot be formatted)The card may be defective.
Replace it.
The operations for...

74
Saving the data settings on the
card
Select the file No.
Give a title to the selected file.
Setup card operations
1Perform the menu operations (pages 84 to 86),
and display the “CAM CARD READ/WRITE”
screen.
n< CAM CARD READ/WRITE >
SELECT      :1
READ
SELECT      :1
WRITE
CARD CONFIG
TITLE READ
READ USER DATA
TITLE:
1:             5:
2:             6:
3:             7:
4:             8:4Turn the JOG dial button to move the arrow
(cursor) to the “TITLE : ” item.
< CAM CARD READ/WRITE >
SELECT      :1...

75
If one of the following messages appears when the JOG dial
button is pressed, the data cannot be saved.
14Press the MENU button to exit the menu
operations.
The setting menu is cleared, and the displays
showing the unit’s current statuses appear at the
top and bottom of the viewfinder screen.
Error messageRemedial action
WRITE NG
NO CARD
(setup card has not been
inserted)Insert the card.
WRITE NG
FORMAT ERROR
(formatting error)The card was formatted by a
device other than the unit.
Replace the card....

76
6Turn the JOG dial button to move the arrow
(cursor) to YES, and press the JOG dial button.  
When the data loading is completed, the following
message appears.
To load the VTR unit’s data, open the VTR CARD
READ/WRITE screen, and perform steps 
4to 6.
< CAM CARD READ/WRITE >
READ
SELECT      :1
WRITE
SELECT      :1
CARD CONFIG
READ USER DATA
TITLE        :
READ OK
YES
nNO
TITLE        :
22222222
Loading the data saved on the
card
Setup card operations
Select the file No.
Load the data of the selected...

77
Setup card operations
If one of the following messages appears when the JOG dial
button is pressed, the data cannot be loaded.
7Press the MENU button to exit the menu
operations.
The setting menu is cleared, and the displays
showing the unit’s current statuses appear at the
top and bottom of the viewfinder screen.
Error messageRemedial action
READ NG
NO CARD
(setup card has not been
inserted)Insert the card.
READ NG
FORMAT ERROR
(formatting error)The card was formatted by a
device other than the...

78
Loading a cassette tape
Cassette tapes
1Check that there are no cables around the cassette
holder or top panel, and set the POWER switch to
ON.

When condensation has formed inside the unit, the
HUMID display lights.  Wait until this display is
cleared before proceeding with the intended
operation.
Ejecting the cassette tape
While the power is still on, press the EJECT button to
open the cassette holder, and take out the cassette
tape.  If another cassette is not going to be loaded
immediately after...

79
This section describes the basic steps for shooting
and recording.
Before actually departing to shoot scenes, carry out
inspections to ensure that the system is functioning
properly.
OFor details on how to perform these inspections,
refer to “Inspections prior to shooting” (pages 126
to 129).
From providing the power supply to
loading the cassette
Recording
1Install a fully charged battery pack.
From adjusting the white balance and
black balance to stopping the recording
Turn on the power, and after...

80
Shooting
Recording
1-1Select the filter to match the lighting conditions,
and set the WHITE BAL switch to “A” or “B” if
the white balance has been stored in the
memory ahead of time.
If the white balance and/or black balance
have not been stored in the memory and
there is no time to adjust the white balance:
Set the WHITE BAL switch to PRST.  The
white balance for the filter is achieved in
accordance with the setting position of the
FILTER control (outer).
1-2When adjusting the white balance on the...