Panasonic Aj Hdc27a Servece Information Manual

INF-19(CAM DESIGN MENU)
ITEMSETTING
RANGEINIT.
VA L U EMEANING of SETTING &
OUTLINE of FUNCTION
LSI REG SET1 A (0) or B (1) ----- ----- Not used
MEMORY SEL ----- ----- Not used
ADR_H ----- -----
ADR_L ----- -----Data address of Flash memory (at CAM_SYS)
DATA_H ----- -----
DATA_L ----- -----Data value of Flash memory (at CAM_SYS)
WRITE ----- ----- STORE command of Adjustment data
(To Flash memory)
READ ----- ----- READ command of Adjustment data
(From Flash memory)
LSI REG SET2 A (0) or B (1) ----- -----...

INF-20(CAM DESIGN MENU)
ITEMSETTING
RANGEINIT.
VA L U EMEANING of SETTING &
OUTLINE of FUNCTION
DSP D/A SET GAIN G ----- ----- G A/D converter input gain adjustment
GAIN B ----- ----- B A/D converter input gain adjustment
GAIN R ----- ----- R A/D converter input gain adjustment
CPL G ----- ----- G A/D converter input clamp level adjustment
CPL B ----- ----- B A/D converter input clamp level adjustment
CPL R ----- ----- R A/D converter input clamp level adjustment
ND POSITION1 R -127-+128 0 R GAIN...

INF-21
9-4. VTR SERVICE 2/3
ITEMSETTING
RANGEINIT.
VA L U EBackupBackup
(INH.)MEANING of SETTING &
OUTLINE of FUNCTION
T TORQUE -128-+127 0 OK NG Take-up reel torque adjustment
S TORQUE -128-+127 0 OK NG Supply reel torque adjustment
PG SHIFT 100 ----- ----- PG shifter adjustment
    HSW_A_RIZE 0-4095 0x500 OK NG Rising edge
  HSW_A_FALL 0-4095 0x500 OK NG Falling edge
  HSW_C_RIZE 0-4095 0x500 OK NG Rising edge
  HSW_C_FALL 0-4095 0x500 OK NG Falling edge
RPL GAIN 100 -128-+127 64 OK NG RPL head ATF...

INF-22
9-7. TEST MODE
ITEM SETTING RANGE INIT. VALUEMEANING of SETTING &
OUTLINE of FUNCTION
AGING MODE OFF/ON OFFON : TEST MODE (VTR RUNNING TEST)
(Repeat 5 minutes REC and 1 minute STAND-BY)
9-8. ERROR LOG
ITEM SETTING RANGE INIT. VALUEMEANING of SETTING &
OUTLINE of FUNCTION
FILE No. 1-5 1 Be able to select 1 through 5.
1 : Old Error Data 
® 4 : Recent Error Data
5 : First Error
      (Cannot delete until execute LOG ALL CLEAR)
LOG ALL CLEAR OFF/ON OFF ON : All Clear
Finally, turn OFF or POWER OFF....

INF-23
10.  Adjustment after Optical Unit Replacement
When replace the Optical Unit (PRE AMP, CCD
PULSE, DRIVE Board included), execute the
adjustment as following procedures.
In this case, do not need to execute the Optical Unit
Adjustment on the “Section 5 : Electrical Adjustment”.
10-1. Input the Adjustment Data
1.  Set the Shading Correction to “OFF” as follows.
  *** CAM MAIN MENU 4 ***
   < BLACK SHADING >
 ® CORRECT (DIG) : “ON“ ® “OFF”
   < WHITE SHADING >
 ® CORRECT  : “ON“ ® “OFF”
2.  Input the...

INF-24
11.DIAG-MENU Display
11-1-1. Version Display Operation Procedure (CAMERA Part)
1.  Open the “ENG menu” (Press “MENU Button” more than 3 second.)
2. Open “CAM MAIN MENU 4
” page (Press JOG Dial)
3. Select “DIAGNOSTIC” page (Turn and Press JOG Dial), then the Software version for each item can be
comfirmed.
11-1-2. How to read the Version Display
11-2-1. Version Display Operation and Hour Meter Display (VTR Part)
1.  Open the “ENG menu” (Press “MENU Button” more than 3 second.)
2.  Press “MENU...

INF-25
11-2-3. How to Reset Hour Meter
1.  Open the “Design Menu” and then press “MENU Button”.
2. Open “VTR DESIGN MENU
” page. (Press JOG Dial)
3.  Select “VTR DESIGN MENU” item. (Turn & press JOG Dial)
4.  After the following figure is displayed, move “®” to the item to reset.
  **** VTR DESIGN MENU  ****
  
®VTR DESIGN MENU
TEST MDOE
ERROR LOG
VM PLD V0.00
VTR SYSCON V18388a
00.06.13
    
 MENU ALL INIT
   
®DRUM RUNNING RESET
 THREADING RESET 

INF-26
12. Error Rate Display and Confirmation Method
12-1. Error Rate Display Method
1.  Open the “VTR SERVICE MENU”.
2. Select “VTR SERVICE 1/3
” page.(Turn & press JOG Dial)
3. Confirm “BER SPEED
” setting is “SLOW
”.
4. Select BER ADJ
 by rotating JOG Dial and Select R/P head to be confirmed.
BER ADJ item :OFF / L1L3 / R1R3 / L2L4 / R2R4 (exept OFF)
5.  The Error rate will be displayed in the Audio meter on the Audio LCD panel.
- 
¥
¥¥ ¥ -
- 40 -
dB - 30 -
- 20 - - 10 -- 0 - AUDIO LCD METER
Error...

INF-27
13. Internal Switch Setting Method
The switche settings on each circuit board are shown below.
  “Factory use only” switches must be set to the “Factory setting”.
BOARD Ref. No. SWFACTORY
SETTINGFEATURE
AUDIO LCD 1-7 ON (FIXED) Factory use onlySW 40001
8 ON Not used
1-5 OFF(FIXED) Factory use onlySW 40002
6 OFF ON : ENG SEQURITY ON
1 ON Factory use only
2 OFF Factory use only
3 ON Factory use onlySW 47001
4 OFF Factory use only
SW 41001 - -60 REAR CH1 MIC input level setting (-60dBu / -40dBu)
SW...

INF-28
14. Circuit board layout
E5. CAMERA MOTHER P.C.BOARD
E37. HD SDI TX P.C.BOARDE10. VTR SYSCON P.C.BOARDE36. VIDEO MAIN P.C.BOARDE14. RF EQ P.C.BOARD
E19. POWER SW P.C.BOARD
E24. MENU SW P.C.BOARD
E20. TOGGLE SW P.C.BOARD
E23. USER SW P.C.BOARD
E21. MONITOR SW P.C.BOARD
E22. SYNCHRO SW P.C.BOARD
E17. AUDIO LCD P.C.BOARD
E16. POWER SUB P.C.BOARD
E15. POWER MAIN P.C.BOARD
E27. EXT DC P.C.BOARD
E26. HEAD PHONE P.C.BOARD
E40. SDI BNC P.C.BOARD
E18. REAR JACK P.C.BOARD
E32. OPERAT E P.C.BOARDE38. BACK...