Panasonic Aj Hdc27a Servece Information Manual

INF-9
7. Cleaning Method
Note:
Turn the power OFF during cleaning.
Make sure the power is OFF before cleaning.
Use ethanol (more than 99% purity) as cleaning
liquid.
7-1. Cylinder Head Cleaning
Method: (Daily)
Clean heads by applying even pressure and rotating
cylinder a few times. Never wipe in up and down
motion. Never touch a cylinder by bare hand. At first
wipe with a cloth dipped in cleaning liquid. Then wipe
with dry cloth.
7-2. Cylinder Lead Cleaning
Method: (Weekly)
Don’t touch a head chip. Clean...

INF-10
8. Basic Setting Menu Operations
8-1. Service Menu Operation
1.  Press the “SHIFT” and “+” buttons of the Time Code Operation Button simultaneously and press the MENU
button, and CAMERA unit’s SERVICE MENU screen is displayed.
2.  When the MENU button is pressed again, the VTR unit’s SERVICE MENU screen is displayed.
CAM MAIN MENU1
Press the “SHIFT” & “+” buttons
simultaneously, and press the MENU button.
Press the
MENU button.VTR MAIN MENU
Press the JOG
dial button.
CAM MAIN MENU2
CAM MAIN MENU3...

INF-11
8-2. Design Menu Operation
1.  Press the “SHIFT” and “RESET” buttons of the Time Code Operation Button simultaneously and press the
MENU button, and switch to the CAMERA unit’s SERVICE MENU screen display mode. At first “CAM MAIN
MENU1” screen is displayed as shown below, but by pressing the JOG Dial button following screen through
the “CAM DESIGN MENU” is displayed .
2.  The SERVICE MENU and DESIGN MENU Can be displayed by pressing the JOG Dial button.
Press the “SHIFT” & “RESET” buttons...

INF-12
8-3. Displaying Sub-Menus and
Setting Procedures
Setting procedures are same for both the USER
MENU and ENGINEER MENU.
1. Turn the JOG Dial button while the USER MENU
screen or MAIN MENU screen is displayed.
The cursor moves to the SUB MENU item.
Example :2. Move the cursor to the desired SUB MENU item,
and press the JOG Dial button.
The SUB MENU is now displayed.
(The cursor appears besidce the title part of the
SUB MENU.)
Example :
Turn the JOG
Dial button.
**** CAM MAIN MENU1 ****
ROP
MATRIX...

INF-13 3. Turn the JOG Dial button to move the cursor to the
desired item to be set, and press the JOG Dial
button.
The digit which value is to be set now flashes.
Example :
4. Turn the JOG Dial button to change the setting.
5. When the desired setting is shown, press the JOG
Dial button.
The setting is now entered.
6. When other items are to be set, turn the JOG Dial
button to move the cursor, and charge and enter
the settings by repeating steps 3 through 5.7. To move to the another SUB MENU, turn the...

INF-14
8-4. Setting Menu Configurations
CAM SERVICE MENU
ENTRY (AUTO)
ENTRY (MANUAL)
WHITE SHADINGPICKUP LEVEL R
PICKUP LEVEL G
PICKUP LEVEL B
START
H CURSOR COARSE
H CURSOR FINE
V CURSOR COARSE
V CURSOR FINE
DEFECT SIZE
DEFECT COLOR
GAIN
OFFSET LEVEL A
OFFSET LEVEL B
ENTRY
CANCEL
DEFECT NO.
DEFECT SIZE
DEFECT COLOR
GAIN
OFFSET LEVEL A
OFFSET LEVEL B
CHANGE
DELETE
ALL DATA CLEAR
DETECTION (DIGITAL)
EDIT / DELETE SERVICE ADJ R GAMMA 
(SERV)
G GAMMA (SERV)
B GAMMA (SERV)
DEFECT COMPENSATION COMPENSATION...

INF-15
CAM DESIGN MENU
VDRIVE 1
NO COMPENSATIONR_0G
R_SUB
R_RESET DC
DA RESET VAH
G_0G
G_SUB
G_RESET DC
B_0G
B_SUB
B_RESET DC
VDRIVE 2
PREPRO 1 G_WS_OFFSET
B_WS_OFFSET
R_WS_OFFSET
G_PRE_CLIP
B_PRE_CLIP
R_PRE_CLIP
G_PULCAN
B_PULCAN
R_PULCAN
PREPRO 2
LSI REG SET 1
LSI REG SET 2
LSI C REG SET
AD READ TEST
DSP D/A SETR_GAIN
G_GAIN
B_GAIN
R_PED
G_PED
B_PED
R_KNPT
G_KNPT
B_KNPT
A (0) or B (1)MEMORY SEL
ADR-H
ADR-L
DATA-H
DATA-L
WRITE
READA (0) or B (1)MEMORY SEL
ADR-H
ADR-L
DATA-H
DATA-L
SHAD DA SET
KNEE APA...

INF-16
VTR DESIGN MENU
VTR DESIGN MENU
TEST MODE
ERROR LOGMENU ALL INIT
DRUM RUNNING RESET
THREADING RESET
FILE No.
LOG ALL CLEAR
  ERROR CODE
AGING MODE
  SEQUENCE No.
  DATE
  TIME
OPERATION TIME
TAPE TOTAL
TAPE REMAIN
BATTERY METER
OBJ/MODE
VTR SERVICE MENU
VTR SERVICE 1/3
VTR SERVICE 2/3
VTR SERVICE 3/3
VTR D/A DATACONCEAL
INNER ECC
OUTER ECC
VITERBI
ADJUST ADDRESS
AUDIO PB SEL
AUDIO SAVE
AUDIO CH7/8
ADJUST DATA
BER ADJ
BER SPEED
CW  REC
AUTO EQ
RDS. REC ADJ
RDS TYPE
SERVO MODE
T TORQUE
S TORQUE
PG...

INF-17
9. Service Menu Item Contents
< CAMERA Section >
9-1. CAM SERVICE MENU
ITEMSETTING
RANGEINIT.
VA L U EMEANING of SETTING &
OUTLINE of FUNCTION
SERVICE ADJ R GAMMA (SERV) -30-+30 00 Adjustment for R GAMMA.
G GAMMA (SERV) -30-+30 00 Adjustment for G GAMMA.
B GAMMA (SERV) -30-+30 00 Adjustment for B GAMMA.
DEFECT COMPENSATION ON/OFF ON ON/OFF switching of blemish compensation.
COMPENSA- COMP ON GAIN -3dB-+30dB 12dB Specified gain of blemish compensation.
TION INTERLACE MODE PDMIX/FRAME PDMIX Select a...

INF-18
9-2. CAM DESIGN MENU
ITEMSETTING
RANGEINIT.
VA L U EMEANING of SETTING &
OUTLINE of FUNCTION
VDRIVE 1 R_OG 00-FF FF OG voltage setting of R CCD.
R_SUB 00-FF 7E Sub voltage setting of R CCD.
R_RESET DC 00-FF 26 Reset DC voltage setting of R CCD.
G_OG 00-FF FF OG voltage setting of G CCD.
G_SUB 00-FF 7E Sub voltage setting of G CCD.
G_RESET DC 00-FF 26 Reset DC voltage setting of G CCD.
B_OG 00-FF FF OG voltage setting of B CCD.
B_SUB 00-FF 7E Sub voltage setting of B CCD.
B_RESET DC 00-FF 26 Reset...