Panasonic Aj Hdc27a Servece Information Manual
Have a look at the manual Panasonic Aj Hdc27a Servece Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
INF-9 7. Cleaning Method Note: Turn the power OFF during cleaning. Make sure the power is OFF before cleaning. Use ethanol (more than 99% purity) as cleaning liquid. 7-1. Cylinder Head Cleaning Method: (Daily) Clean heads by applying even pressure and rotating cylinder a few times. Never wipe in up and down motion. Never touch a cylinder by bare hand. At first wipe with a cloth dipped in cleaning liquid. Then wipe with dry cloth. 7-2. Cylinder Lead Cleaning Method: (Weekly) Don’t touch a head chip. Clean the drum lead with a pick. 7-3. A/C Head Cleaning Method: (Weekly) Wipe the A/C head with a cloth dipped in cleaning liquid. Wipe again with a dry cloth. 7-4. Pinch Roller and Capstan Shaft Cleaning Method: (Weekly) Wipe the Pinch Roller and Capstan with a cloth dipped in cleaning liquid. 7-5. Post Cleaning Method: (Weekly) Wind a cloth on a pick. Wipe each posts with that pick. Wipe again with a dry cloth. For metal posts wipe with a cloth dipped in cleaning liquid. Then wipe it again with dry cloth. Notes : Use the clean cloth for cleaning purpose. Do not use any dirty cloth. The cleaning cloth can be ordered as spare parts. The part number is indicated as below. CLEANING CLOTH : VZZ0095 Upper Cylinder Lower Cylinder Head Lead Cleaning Cloth CYLINDER Cotton Swab
INF-10 8. Basic Setting Menu Operations 8-1. Service Menu Operation 1. Press the “SHIFT” and “+” buttons of the Time Code Operation Button simultaneously and press the MENU button, and CAMERA unit’s SERVICE MENU screen is displayed. 2. When the MENU button is pressed again, the VTR unit’s SERVICE MENU screen is displayed. CAM MAIN MENU1 Press the “SHIFT” & “+” buttons simultaneously, and press the MENU button. Press the MENU button.VTR MAIN MENU Press the JOG dial button. CAM MAIN MENU2 CAM MAIN MENU3 CAM MAIN MENU4 Press the JOG dial button. Press the JOG dial button. Press the JOG dial button. Press the MENU button. Press the MENU button. Press the MENU button. CAM SERVICE MENU Press the JOG dial button. Press the MENU button. Press the JOG dial button. VTR SERVICE MENU Press the JOG dial button.
INF-11 8-2. Design Menu Operation 1. Press the “SHIFT” and “RESET” buttons of the Time Code Operation Button simultaneously and press the MENU button, and switch to the CAMERA unit’s SERVICE MENU screen display mode. At first “CAM MAIN MENU1” screen is displayed as shown below, but by pressing the JOG Dial button following screen through the “CAM DESIGN MENU” is displayed . 2. The SERVICE MENU and DESIGN MENU Can be displayed by pressing the JOG Dial button. Press the “SHIFT” & “RESET” buttons simultaneously, and press the MENU button. CAM MAIN MENU1Press the MENU button.VTR MAIN MENU Press the JOG dial button. CAM MAIN MENU2 CAM MAIN MENU3 CAM MAIN MENU4 Press the JOG dial button. Press the JOG dial button. Press the JOG dial button. Press the MENU button. Press the MENU button. Press the MENU button. CAM SERVICE MENU Press the JOG dial button. Press the MENU button. Press the JOG dial button. VTR SERVICE MENU Press the JOG dial button. CAM DESIGN MENUPress the JOG dial button.Press the MENU button. VTR DESIGN MENU Press the JOG dial button.
INF-12 8-3. Displaying Sub-Menus and Setting Procedures Setting procedures are same for both the USER MENU and ENGINEER MENU. 1. Turn the JOG Dial button while the USER MENU screen or MAIN MENU screen is displayed. The cursor moves to the SUB MENU item. Example :2. Move the cursor to the desired SUB MENU item, and press the JOG Dial button. The SUB MENU is now displayed. (The cursor appears besidce the title part of the SUB MENU.) Example : Turn the JOG Dial button. **** CAM MAIN MENU1 **** ROP MATRIX COLOR CORRECTION1 COLOR CORRECTION2 LOW SETTING MID SETTING HIGH SETTING ADITIONAL DTL1 ADITIONAL DTL2 SKIN TONE DTL KNEE / LEVEL GAMMA CAMERASETTING Press the JOG Dial button. **** CAM MAIN MENU1 **** ROP MATRIX COLOR CORRECTION1 COLOR CORRECTION2 LOW SETTING MID SETTING HIGH SETTING ADITIONAL DTL1 ADITIONAL DTL2 SKIN TONE DTL KNEE / LEVEL GAMMA CAMERASETTING < ROP > MASTER PED : +008 MASTER DTL : +00 MASTER GAMMA : 0.45 R GAIN : +000 G GAIN : +000 B GAIN : +000 R PEDESTAL : +000 G PEDESTAL : +000 B PEDESTAL : +000
INF-13 3. Turn the JOG Dial button to move the cursor to the desired item to be set, and press the JOG Dial button. The digit which value is to be set now flashes. Example : 4. Turn the JOG Dial button to change the setting. 5. When the desired setting is shown, press the JOG Dial button. The setting is now entered. 6. When other items are to be set, turn the JOG Dial button to move the cursor, and charge and enter the settings by repeating steps 3 through 5.7. To move to the another SUB MENU, turn the JOG Dial button to move the cursor to the title part of the SUB MENU, and press the JOG Dial button. The USER MENU screen or MAIN MENU screen is now displayed, so proceed with operation by following the same steps. Example : 8. Upon completion of the settings, press the MENU button. Then the settings are now saved, exit the settings menu mode, and return-to the normal operation mode. NOTE : To exit the camera unit’s menu, press the MENU button twice. When the MENU button is pressed once, operation is transferred to the VTR unit’s menu. < ROP > MASTER PED : +008 MASTER DTL : +00 MASTER GAMMA : 0.45 R GAIN : +000 G GAIN : +000 B GAIN : +000 R PEDESTAL : +000 G PEDESTAL : +000 B PEDESTAL : +000 Press the JOG Dial button. < ROP > MASTER PED : +008 MASTER DTL : +00 MASTER GAMMA : 0.45 R GAIN : +000 G GAIN : +000 B GAIN : +000 R PEDESTAL : +000 G PEDESTAL : +000 B PEDESTAL : +000 Press the JOG Dial button.
INF-14 8-4. Setting Menu Configurations CAM SERVICE MENU ENTRY (AUTO) ENTRY (MANUAL) WHITE SHADINGPICKUP LEVEL R PICKUP LEVEL G PICKUP LEVEL B START H CURSOR COARSE H CURSOR FINE V CURSOR COARSE V CURSOR FINE DEFECT SIZE DEFECT COLOR GAIN OFFSET LEVEL A OFFSET LEVEL B ENTRY CANCEL DEFECT NO. DEFECT SIZE DEFECT COLOR GAIN OFFSET LEVEL A OFFSET LEVEL B CHANGE DELETE ALL DATA CLEAR DETECTION (DIGITAL) EDIT / DELETE SERVICE ADJ R GAMMA (SERV) G GAMMA (SERV) B GAMMA (SERV) DEFECT COMPENSATION COMPENSATION COMP ON GAIN INTERLACE MODE R CH G CH B CH TRIPLE OFFSET CURSOR BOX READ DATA WRITE DATA NG LIST NO SELECT ENTRY CURSOR DISP R/W SEL READ WRITECAM SERVICE CARD R/W
INF-15 CAM DESIGN MENU VDRIVE 1 NO COMPENSATIONR_0G R_SUB R_RESET DC DA RESET VAH G_0G G_SUB G_RESET DC B_0G B_SUB B_RESET DC VDRIVE 2 PREPRO 1 G_WS_OFFSET B_WS_OFFSET R_WS_OFFSET G_PRE_CLIP B_PRE_CLIP R_PRE_CLIP G_PULCAN B_PULCAN R_PULCAN PREPRO 2 LSI REG SET 1 LSI REG SET 2 LSI C REG SET AD READ TEST DSP D/A SETR_GAIN G_GAIN B_GAIN R_PED G_PED B_PED R_KNPT G_KNPT B_KNPT A (0) or B (1)MEMORY SEL ADR-H ADR-L DATA-H DATA-L WRITE READA (0) or B (1)MEMORY SEL ADR-H ADR-L DATA-H DATA-L SHAD DA SET KNEE APA SETBSHD_R BSHD_G BSHD_B WSHD_G_SUB WSHD_B WSHD_G WSHD_R IRIS_C THRESH LEVEL SLOPE FREQ. GAIN CORING LVL DTL COMP (+)DTL COMP(–)DTL CLIP (+)DTL CLIP (–)KNEE SET ADR DATA WRITE IRIS POS ZOOM POS FOCUS POS LENS EXT CC FILT ND FILT PEAKING FRAME ZEBRA MARK SW GAIN G GAIN B GAIN R CPL G CPL B CPL R POSITION 1 R B POSITION 2 R B POSITION 3 R B POSITION 4 R B VA13M VA24M VAL VBL LG HPP 0D P16V R_PADC G_PADC B_PADC H1DC H2DC VSHIN M_PED DESIGNMENU ALL INIT FACTORY MENU
INF-16 VTR DESIGN MENU VTR DESIGN MENU TEST MODE ERROR LOGMENU ALL INIT DRUM RUNNING RESET THREADING RESET FILE No. LOG ALL CLEAR ERROR CODE AGING MODE SEQUENCE No. DATE TIME OPERATION TIME TAPE TOTAL TAPE REMAIN BATTERY METER OBJ/MODE VTR SERVICE MENU VTR SERVICE 1/3 VTR SERVICE 2/3 VTR SERVICE 3/3 VTR D/A DATACONCEAL INNER ECC OUTER ECC VITERBI ADJUST ADDRESS AUDIO PB SEL AUDIO SAVE AUDIO CH7/8 ADJUST DATA BER ADJ BER SPEED CW REC AUTO EQ RDS. REC ADJ RDS TYPE SERVO MODE T TORQUE S TORQUE PG SHIFT 100 HSW_A_RIZE HSW_A_FALL HSW_C_RIZE HSW_C_FALL RPL GAIN 100 RPL LIN 100 CTL ADJ X VALUE SET X VALUE 100 TRK VAL 100 SERVO MODE ADJUST ADDRESS ADJUST DATA
INF-17 9. Service Menu Item Contents < CAMERA Section > 9-1. CAM SERVICE MENU ITEMSETTING RANGEINIT. VA L U EMEANING of SETTING & OUTLINE of FUNCTION SERVICE ADJ R GAMMA (SERV) -30-+30 00 Adjustment for R GAMMA. G GAMMA (SERV) -30-+30 00 Adjustment for G GAMMA. B GAMMA (SERV) -30-+30 00 Adjustment for B GAMMA. DEFECT COMPENSATION ON/OFF ON ON/OFF switching of blemish compensation. COMPENSA- COMP ON GAIN -3dB-+30dB 12dB Specified gain of blemish compensation. TION INTERLACE MODE PDMIX/FRAME PDMIX Select a way of correct operation. R CH AVE/OFSET AVE Adjacent Picture Element Compensation/ G CH AVE/OFSET AVE Level Decrease B CH AVE/OFSET AVE TRIPLE OFFSET BAB/BBA BAB 3 adjacent picture elements decrease. CURSOR BOX ON/OFF ON Indicate the box on the cursor. READ DATA ON/OFF OFF Read the defect data. WRITE DATA ON/OFF OFF Write the defect data. ENTRY (AUTO) PICKUP LEVEL R 1-40 15 Detection Level of blemish. PICKUP LEVEL G 1-40 10 Detection Level of blemish. PICKUP LEVEL B 1-40 25 Detection Level of blemish. START ON/OFF OFF ON/OFF Switching of Auto detection. NG LIST NO 0-63 000 Display the NG List No. SELECT OFF/A/B OFF Factory Use ENTRY ON/OFF OFF Factory Use CURSOR DISP ON/OFF ON Factory Use ENTRY (MANUAL)H CURSOR COARSE00-08 03 Coarse Adjustment for Horizontal Cursor Position H CURSOR FINE 00-FF 80 Fine Adjustment for Horizontal Cursor Position V CURSOR COARSE00-04 02 Coarse Adjustment for Vertical Cursor Position V CURSOR FINE 00-FF 80 Fine Adjustment for Vertical Cursor Position DEFECT SIZE 1-3 1 Sequential Number of blemish. DEFECT COLOR Y/R/G/B Y The color which has blemish. GAIN ON/OFF ON ON/OFF switching of compensation followed gain. OFFSET LEVEL A 0-255 100 Set the decrease value. OFFSET LEVEL B 0-255 100 Set the decrease value. ENTRY ON/OFF OFF ON/OFF switching of blemish entry of above data. CANCEL ON/OFF OFF Cancel for just before entry. EDIT/DELETE DEFECT NO. 0-255 0 Indicate the blemish data of specified number. DEFECT SIZE 1-3 1 Sequential Number of blemish. DEFECT COLOR Y/R/G/B Y The color which has blemish. GAIN ON/OFF ON ON/OFF switching of compensation followed gain. OFFSET LEVEL A 0-255 100 Set the decrease value. OFFSET LEVEL B 0-255 100 Set the decrease value. CHANGE ON/OFF OFF Entry the above data. DELETE ON/OFF OFF Delete above entry data. ALL DATA CLEAR ON/OFF OFF Delete all of entry data. WHITE SHADINGDETECTION (DIGITAL)--- --- Execute the Digital white shading. CAM SERVICE CARD R/WR/W SEL DESIGN/SHADI NG/DEFECT--- Select the R/W DATA READ --- --- Read the DATA from the card. WRITE --- --- Write the DATA to the card.
INF-18 9-2. CAM DESIGN MENU ITEMSETTING RANGEINIT. VA L U EMEANING of SETTING & OUTLINE of FUNCTION VDRIVE 1 R_OG 00-FF FF OG voltage setting of R CCD. R_SUB 00-FF 7E Sub voltage setting of R CCD. R_RESET DC 00-FF 26 Reset DC voltage setting of R CCD. G_OG 00-FF FF OG voltage setting of G CCD. G_SUB 00-FF 7E Sub voltage setting of G CCD. G_RESET DC 00-FF 26 Reset DC voltage setting of G CCD. B_OG 00-FF FF OG voltage setting of B CCD. B_SUB 00-FF 7E Sub voltage setting of B CCD. B_RESET DC 00-FF 26 Reset DC voltage setting of B CCD. H1DC 00-FF 80 H1 DC setting value of CCD. H2DC 00-FF 80 H2 DC setting value of CCD. VSHIN 00-FF FF Read voltage of CCD. VDRIVE 2 VAH 00-FF 2E Read Out Pulse voltage of CCD (VH) VA13M 00-FF 00 Transfer Pulse voltage of CCD (VM13) VA24M 00-FF FF Transfer Pulse voltage of CCD (VM24) VAL 00-FF 40 Transfer Pulse voltage of CCD (VAL) VBL 00-FF 40 Transfer Pulse voltage of CCD (VBL) LG 00-FF 6A Output Amp Voltage of CCD (LG) HPP 00-FF FF H Transfer Pulse voltage of CCD (H) 0D 00-FF FF Output Amp Voltage of CCD (OG) P16V 00-FF FF CCD Drive voltage (16V) R_PADC 00-FF A8 Offset Adjustment for Rch Pre Amp G_PADC 00-FF 98 Offset Adjustment for Gh Pre Amp B_PADC 00-FF C7 Offset Adjustment for Bch Pre Amp DA RESET OFF/ON OFF Initialize the all DA data. PRE PROCESS1 G_WS_OFFSET ----- ----- G WHITE SHADING OFFSET Adjustment B_WS_OFFSET ----- ----- B WHITE SHADING OFFSET Adjustment R_WS_OFFSET ----- ----- R WHITE SHADING OFFSET Adjustment G_PRE_CLIP ----- ----- Factory Use (Fixed at Factory) B_PRE_CLIP ----- ----- Factory Use (Fixed at Factory) R_PRE_CLIP ----- ----- Factory Use (Fixed at Factory) G_PULCAN ----- ----- G PULSE CANCEL Adjustment B_PULCAN ----- ----- B PULSE CANCEL Adjustment R_PULCAN ----- ----- R PULSE CANCEL Adjustment PRE PROCESS2 R_GAIN ----- ----- G_GAIN ----- ----- B_GAIN ----- -----AWB Adjustment Value R_PED ----- ----- G_PED ----- ----- B_PED ----- -----ABB Adjustment Value M_PED ----- ----- Master Pedestal Value (For 0IRE Adjustment) G_KNPT ----- ----- G Knee point value B_KNPT ----- ----- B Knee point value R_KNPT ----- ----- R Knee point value