Panasonic Aj D900wa Operating Instructions Manual

–51–
Lamp Displays Inside the View finder
The viewfinder displays are as follows.
1. REC (recording) lamp
This lamp lights (red) during recording, and flashes when warnings are issued.
ÁSee “Warning System” (page 125) for a detailed description.
2. BATT (battery) lamp
When the battery voltage has dropped, this lamp begins flashing several minutes before the
unit can no longer be operated, and lights when the unit can no longer be operated.
To prevent operation from being interrupted, exchange the battery...

–52–
Lamp Displays Inside the View finder
Setting the ! Lamp Display
Items subject to ! lamp display are selected at the ! LED page of the setting menu. (When
shipped from the factory, the unit is set so that the ! LED page is not displayed.) To operate the
! LED page, switch the unit to engineer mode or select the ! LED page at the MENU SELECT
page.
ÁSee “Setting Menu Configuration” (page 47) for engineer mode and selection of displayed
pages.
1Set the MENU SET/OFF switch to SET.
The setting status...

–53–
Status Displays Inside the View finder Screen
In addition to images, messages indicating the unit’s settings and operating status appear on the
viewfinder screen. The center marker and safety zone marker, etc. are also displayed.
When the MENU SET/OFF switch is set to OFF, items set to SET at the VF DISPLAY page of
the setting menu and using related switches appear at the top and bottom of the screen.
Messages informing of the setting contents or of the adjustment course or results can also be...

–54–
Status Displays Inside the View finder Screen
1
Extender display
This is displayed when the lens extender is being used.
2Shutter speed/mode display
This displays the shutter speed or shutter mode setting.
OFF:The shutter is not used.
1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000:
Shutter speeds (seconds) during standard mode.
1/30.2 – 1/250 (SYNCHRO SCAN):
Synchro scan mode is selected.
SUPER V:High vertical resolution mode is selected.
3Remaining tape length display
This indicates the remaining tape...

–55–
-40-30-25 -20-15-10-5 0

E
8Audio level display
This displays the audio CH1 level.
During sine wave input, the audio level display corresponds roughly to the VTR level
meter display as follows.
9Iris value display
This displays the approximate iris setting (F number).
10Warning display
This displays the black balance, white balance, auto knee function, super iris, super gain
and other warning displays.
11Safety zone marker
This indicates the 80% or 90% (setting when shipped from the factory) range...

–56–
Status Displays Inside the View finder Screen
Selecting Display Items
The items to be displayed on the viewfinder screen can be selected by switching the display
ON/OFF setting independently for each item at the VF DISPLAY page. The items which can be
selected are as follows.
ÁDisplay mode (See “Display Mode and Setting Change/Adjustment Course Message”.)
ÁExtender display
ÁShutter speed/mode display
ÁRemaining tape length display
ÁRemaining battery level display
ÁFilter display
ÁWhite balance...

–57–
Display Mode and Setting Change Message
Messages informing of the contents of changed settings and adjustment results can be limited
to part of the displayed items or not displayed for all items.
The conditions under which messages are displayed and the corresponding display modes are
shown in the table below.
Setting change/adjustment results messages and display modes
Conditions under which
messages are displayedMessage
Display mode
setting
 123
When the filter selection is
changed.
When the gain...

–58–
Status Displays Inside the View finder Screen
Changing the Display Mode
The display mode setting appears on the VF DISPLAY page of the setting menu.
1Perform the operations in steps 1 to 3 of “Selecting Display Items” (page 56) to display the
VF DISPLAY page of the setting menu on the viewfinder screen and align the cursor with
the DISP MODE item.
2Press the UP or DOWN button to select the desired display mode.
3When menu operations have been completed, set the MENU SET/OFF switch to OFF.
Setting...

–59–
Setting the Camera ID
The camera ID can be set at the CAMERA ID page of the setting menu.
A camera ID of up to ten characters including English letters, symbols and spaces can be used.
The camera ID is recorded when the OUTPUT/AUTO KNEE switch is set to BARS and the color
bar signal is being recorded. It is also displayed on the viewfinder screen.
|Note{
When the setting menu is displayed, the camera ID is not displayed even if the color bar signal
is output.
1Set the MENU SET/OFF switch to SET.
The...

–60–
CH1 CH2
20
0
EMPHASIS
dB
10
30
40
E TAPE F
E BATT F
RFSERVOHUMID SLACK DF
SLAVE TCG HOLD WIDE
h min s frm
Displays
Remaining Battery Level and Audio Level Displays
Remaining tape length
When the amount remaining
on the tape is more than
30 minutes long, all seven
segments up to the “F” posi-
tion appear lighted.
When it is less than 30 min-
utes long, one segment will go
off for every 5-minute reduc-
tion in the length.
Remaining battery levelAudio CH level meter
VTR Section Operation/Status-Related...