Panasonic Air Conditioner Cz 64esmc1U Installation Instructions

11
5. Mode setting
According to function of each system controller, set 
SW1 as Fig. 7.
(1) Central control/Remote control mode
z Central control mode
  System controller is used as central control 
equipment.
  Individual setting by remote controller can be 
inhibitted by system controller.
z Remote control mode
  System controller is used as remote controller. 
Setting by system controller is inhibitted by other 
central control equipments.
(2) ALL/ZONE  mode
z ALL mode
  All indoor units can be...

12
6.  How to perform zone registration
To operate the system controller properly, zone registration is required after 
 nishing the test run (and after setting all indoor unit addresses) using one of the 
following methods.
(a) Zone registration using the remote controller  
Refer to page 14
(b) Zone registration using the system controller 
Refer to page 15
(c) Automatic zone registration using the system controller  
Refer to page 16
For methods (a) and (b), you should make a zone registration table...

13

14
(a) Zone registration using the remote controller 
  (Determination of central address)
z In this case, after con rming which indoor unit is connected to the 
remote controller and that the air conditioner in the OFF state, you 
set the central addresses one at a time.
z If the system has no remote controller, connect a remote controller 
to the system temporarily. Then follow this procedure.
NOTE
The indoor unit address must already have been set before performing 
zone registration. If necessary,...

15
(b) Zone registration using the system controller
z In this case, you set all Central addresses by 
system controller at once manually.
(1) Press  the 
 and  buttons at the same time 
for more than 4 seconds. 
 
 and CODE No. C1 will  ash.
(2) After con rming that CODE No. C1 is displayed, 
press the 
 button. Once in this mode, a change 
takes place as Fig. 10.
(3) Select the zone and group No. which you want to 
set with 
 and  (GROUP) buttons.
  If already set, press the 
 buttons.
(4) Set the unit...

16
(c) Automatic zone registration using the system controller 
(1) Press  the 
 and  buttons at the same time for more than 4 
seconds. 
 
 and CODE No. C1 will  ash.
(2) Select CODE. No. C2 by pressing 
 and  (  ) button and 
press the 
 button.
  C2 changes from  ashing to ON state and automatic zone 
registration will start.
(3) Registered GROUP No. will be disappeared all.
(4) Central address will be assigned from small indoor unit address to 
large one in numerical order automatically.
  Finishing...

17
7.  How to check overlapping of central address no.
(1) Press  the  and  buttons at the same time for more than 4 
seconds. 
 
 and CODE No. C1 will  ash.
(2) Select CODE. No. C3 by pressing 
 ,  (  ) button and 
press the 
 button.
  C3 changes from  ashing to ON state and 
 will  ash. Then 
auto. overlap checking will start.
(3) If C3 changes from ON to  ashing and 
 stops  ashing and 
disappears, there is no overlapping.
  Then  nally, complete the auto overlap checking mode by pressing 
the...

18
8.  Memory back up switch
Check the back up switch is ON for back side of system controller PCB.
ON OFF
9. Test run
(1) Power on for all indoor units. Next, power on for system controller. 
 
 will  ash, checking the indoor unit address automatically.
(2) If group No. displayed on system controller is not same as indoor unit No.* 
which is connected, see Fig. 7 and setting again.
  *In case of group control, main unit No. only.
Back up switch
Back up battery...

19
$;&4.$6@FOHJOEE


$;&4.$6@FOHJOEE








 

Printed in Japan
$;&4.$6@FOHJOEE


$;&4.$6@FOHJOEE