Panasonic 8415 Maintenance Manual

Settings and Printing
MaintenanceSpecifications11
When printing on paper or transparency, the media must be loaded in the multi-purpose tray or the
media tray designed for only paper or transparency. When you use multi-purpose tray, the media you
are using must be selected in the printer driver. If media is loaded in the incorrect media tray or
different media is selected in the printer driver, the “Media type mismatch” message will appear on the
LCD panel and jam will occur.
Perform one of the following...

Settings and Printing
MaintenanceSpecifications12
¾ OR ¾
1Remove the media tray or auto duplex printing unit (if installed in your printer).
2Remove the jammed media from inside the printer.
3Reinsert the media tray.
4Open and close the front door to clear the error message from the LCD.
Clearing a Jam 

Settings and Printing
MaintenanceSpecifications13
n Jam at A in the 2nd cassette feeder:
1Open the lower left side door.
2Remove the jammed media.
3Close the lower left side door.
Clearing a Jam 

¾ OR ¾
1Remove the selected media tray (middle or lower media tray).
2Remove the jammed media from inside the printer.
3Reinsert the media tray.
4Open and close the front door to clear the error message from the LCD.
Settings and Printing
MaintenanceSpecifications14
Clearing a Jam 

Settings and Printing
MaintenanceSpecifications15
n Jam at B in the media tray:
1Open the left side door.
2Use the green handles to pull out the paper feeder.
3Remove the jammed media on or under the paper feeder.
4Reinsert the paper feeder and close the left side door.
Clearing a Jam
Jam at B 

Settings and Printing
MaintenanceSpecifications16
n Jam at B in the multi-purpose tray:
1Remove the jammed media from the multi-purpose tray.
2Open and close the front door to clear the error message from the front panel.
NOTE
·A few sheets of paper printed after clearing media jam may be dirty.
Clearing a Jam 

Settings and Printing
MaintenanceSpecifications17
1Open the printer front door.
SAFETY CAUTION
BThe fuser is hot; to avoid personal injury, turn off the printer and wait 10 minutes (after
opening the front door) for the fuser unit to cool before touching it.
2Check whether the media is jammed under the color imaging unit.
If the media jam is not found, go to next step.
·If the media is jammed, 
(a) Remove it by following the steps 1 to 4 in “Jam at B in the media tray” onpage 15.
(b) To clear the error...

Settings and Printing
MaintenanceSpecifications18
3Turn the small green thumbscrew counterclockwise to unlock the fuser unit.
4Holding the green tab on the right, slide the fuser unit out until it stops.
CAUTION:
HOT SURFACE
#Clearing a Jam 

Settings and Printing
MaintenanceSpecifications19
5#Press the green lever on the left to release the safety catch.
$Hold the fuser unit as shown below, and slide it out of the printer.
SAFETY CAUTION
BThe fuser unit weighs approximately 3.1 k
g{6.8 lbs.}. Take care when handling it.
%Close the front door.
SAFETY CAUTION
BDo not touch the roller and the parts around the roller when handling the fuser unit,
because they may be hot.
$
%
Roller
Clearing a Jam
CAUTION:
HOT SURFACE
!
# 

6Remove the oil supply roll:
#Press out on tabs to unlock the oil supply roll.
$Remove the oil supply roll out of the fuser.
NOTE
BIf the paper is not jammed in the fuser unit, repeat steps 1 to 4 in “Jam at B in the media
tray” on page 15.
7Holding the tabs, remove the cleaning pad.
Settings and Printing
MaintenanceSpecifications20
#
#
$
Cleaning pad
Clearing a Jam