Optoma X306st Projector User Manual

31English
User Controls
 Sharpness
Adjust the sharpness of the image.
  Press the  to decrease the sharpness.
  Press the  to increase the sharpness. 
  Color
Adjust a video image from black and white to fully saturated color .
  Press the  to decrease the amount of saturation in the image.
  Press the  to increase the amount of saturation in the image. 
  Tint
Adjust the color balance of red and green.
  Press the  to increase the amount of green in the image.
  Press the  to increase the amount...

32English
User Controls
IMAGE | Advanced
 Gamma
This allows you to choose a degamma table that has been  
fine-tuned to bring out the best image quality for the input.
  Film: for home theater.
  Video: for video or TV source.
  Graphics: for image source.
  Standard: for PC or computer source.
  BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and 
system level enhancements to enable higher brightness while 
providing true, more vibrant colors in picture. The range is...

33English
User Controls
   Red/Green/Blue/Cyan/Magenta/Yellow: Use  or  to select 
Hue, Saturation and Gain Colors.
   White: Use  or  to select Red, Green and Blue Colors.
   Reset: Choose “Yes” to return the factory default settings for 
color adjustments.
  Color Space
Select an appropriate color matrix type from AUTO, RGB, 
RGB(0-255)(*), RGB(16-235)(*) or YUV.
 Reset
Choose “Yes” to return the display parameters on all menus to the 
factory default settings.
	(*) For HDMI only.     

34English
User Controls
IMAGE | Advanced 
| Signal (RGB) 
 Automatic
Automatically selects the singal. If you use this function, the 
Phase, frequency items are grayed out, and if Signal is not auto-
matic, the phase, frequency items will appear for user to manually 
tune and saved in settings after that for next time projector turns 
off and on again.
 Phase
Synchronize the signal timing of the display with the graphic card. 
If the image appears to be unstable or flickers, use this function to 
correct...

35English
User Controls
DISPLAY
 Format
Use this function to choose your desired aspect ratio.
XGA
  4:3: This format is for 4×3 input sources.
  16:9: This format is for 16×9 input sources, like HDTV and DVD 
enhanced for Wide screen TV.
  Native: This format displays the original image without any 
scaling.
  AUTO: Automatically selects the appropriate display format.
Auto Input resolutionAuto/Scale
HVHV
4:3
6404801024768
8006001024768
10247681024768
128010241024768
140010501024768
160012001024768...

36English
User Controls
Aspect ratio(source detected) Resize image (XGA)
4:31024 x 768 center
16:91024 x 576 center
NativeNo resize image, 1:1 mapping and centered. This format shows the original image without scaling. 
 
WXGA
  4:3: This format is for 4×3 input sources.
  16:9: This format is for 16×9 input sources, like HDTV and DVD 
enhanced for Wide screen TV.
  16:10: This format is for 16×10 input sources, like widescreen 
laptops.
  LBX: This format is for non-16x9, letterbox source and for...

37English
User Controls
 Edge Mask
Edge mask function removes the noise in a video image. Edge 
mask the image to remove video encoding noise on the edge of 
video source.
 Zoom
  Press the  to reduce the size of an image.
  Press the  to magnify an image on the projection screen.
  Image Shift
Press  into  the  next  menu  as  below  and  then  use  or    to 
select item.
   H: Use  or  to shift the projected image position horizontally.
     V: Use  or  to Shift the projected image position...

38English
User Controls
  3D Mode
  Off: Select “Off” to turn 3D settings off for 3D images.
  DLP Link: Select “DLP Link” to use optimized settings for DLP 
Link 3D images.
  IR (*): Select “IR” to use optimized settings for IR-based 3D 
images.
  3D Format
  Auto : When a 3D identification signal is detected, the 3D 
format is selected automatically.
  SBS: Use this mode for “Side-by-side” format 3D content.
  Top and Bottom: Use this mode for “Top and Bottom” format 3D 
content.
  Frame...

39English
User Controls
SETUP
 Language (*)
Choose the multilingual OSD menu. Press  or  into the sub 
menu and then use the  or  key to select your preferred  
language. Press “Enter” to finalize the selection. 
   
 Projection
    Front-Desktop
This is the default selection. The image is projected straight on 
the screen.
    Rear-Desktop
When selected, the image will appear reversed.
    Front-Ceiling 
When selected, the image will turn upside down.
    Rear-Ceiling 
When selected, the image will...

40English
User Controls
 Menu Location
Choose the menu location on the display screen.
 Screen Type
Choose the screen type from16:10 or 16:9.
 Projector ID
ID definition can be set up by menu (range 0-99), and allow user 
control an individual projector by RS232. Refer to page 65-68 for 
the complete list of RS232 commands.	“Screen Type” is for WXGA only.