Optoma Projector RS232 User Manual
Here you can view all the pages of manual Optoma Projector RS232 User Manual. The Optoma manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 51
51English Appendices Steady light No light LED lighting message MessageON/STANDBY LEDTemp-LEDLamp-LED (Green/Amber)(Red)(Red) Standby State (Input power cord)Amber Power on (Warming)Flashing Green Lamp lightingGreen Power off (Cooling) Flashing Green Error (Over Temp.)Flashing Amber Error (Fan fail)Flashing AmberFlashing Error (Lamp fail)Flashing Amber
Page 52
52English Appendices On Screen Messages Temperature warning: Fan failed: Lamp warning: Out of display range: If the remote control does not work Check the operating angle of the remote control is within ±20° both horizontally and vertically of one of the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (±0°) of the projector. Make sure the batteries are inserted correctly. Replace batteries...
Page 53
53English Appendices Replacing the Lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. Warning: Lamp compartment may be hot! Allow it to cool down before changing the lamp! Warning: To reduce the...
Page 54
54English Appendices Lamp Replacement Procedure: 1. Switch off the power to the projector by pressing the “” button. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the one screw on the cover. 1 5. Lift up and remove the cover. 2 6. Lift up the lamp handle. 3 7. Press on the both sides then lift up and remove the lamp cord. 4 8. Unscrew the one screw on the lamp module. 5 9. Lift up the lamp handle 6 and remove the lamp module slowly and carefully....
Page 55
55English Appendices Installing and Cleaning the Dust Filter Dust filters are only required/sup-plied in selected regions with ex-cessive dust. Installing the Dust Filter Procedure: Install two filters.1. Turn on the projector then press “Menu”, go to “OPTIONS -> Op-2. tional Filter Settings -> Optional Filter Installed” and select “Yes”. 1 Cleaning the Dust Filter We recommends cleaning the dust filter every three months; clean it more often if the projector is used in a dusty environment....
Page 56
56English Appendices Computer/Video/HDMI/Mac Compatibility Compatibility Modes For widescreen resolution (WXGA), the compatibility support is depen-dent on Notebook/PC models.Please note that us- ing resolutions other than native 800 x 600 (SVGA model), 1024 x 768 (XGA model), 1280 x 800 (WXGA model) may result in some loss of image clarity.(*1) 1920 x1200 @60Hz only support RB (reduced blank-ing).(*2) 3D timing for True 3D projector.(*3) is not supported HDMI input signal for Mac.(*4) Proscene...
Page 57
57English Appendices 3D Input Video Compatibility Input Resolution HDMI 1.4a 3D Input Input Timing 1280 x 720p @ 50HzTop-and-Bottom 1280 x 720p @ 60HzTop-and-Bottom 1280 x 720p @ 50HzFrame packing 1280 x 720p @ 60HzFrame packing 1920 x 1080i @ 50 HzSide-by-Side (Half) 1920 x 1080i @ 60 HzSide-by-Side (Half) 1920 x 1080p @ 24 HzTop-and-Bottom 1920 x 1080p @ 24 HzFrame packing HDMI 1.3 3D Content 1920 x 1080i @ 50Hz Side-by-Side (Half)While 3D Format is “SBS” 1920 x 1080i @ 60Hz 1280 x 720p @ 50Hz 1280 x...
Page 58
58English Appendices RS232 Pin Assignments RS232 Commands and Protocol Function List Pin no.Spec. (from projector side) 1N/A 2RXD 3TXD 4N/A 5GND 6N/A 7N/A 8N/A 9N/A 1 2 3 4 5 6 7 8 9
Page 59
59English Appendices RS232 Protocol Function List Baud Rate : 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F 1. There is a after all ASCII commands. 2. 0D is the HEX code for in ASCII code. XX=00-99, projector's ID, XX=00 is for all projectors 1 Optoma V1 Command Table....
Page 60
60English Appendices 2 --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX44 n 7E 30 30 34 35 20 a 0D Tint n = -50 (a=2D 35 30) ~ 50 (a=35 30)...