Optoma Projector RS232 User Manual

							1English
Table of Contents ............................1
Usage Notice ...................................2
Safety Information ...............................2
Precautions  .........................................3
Eye Safety Warnings  ..........................5
Product Features ................................5
Introduction ......................................6
Package Overview  ..............................6
Product Overview  ...............................7
Main Unit ..............................................7
Control Panel  .......................................8
Input/Output Connections ....................9
Remote Control ..................................10
Installation  .....................................11
Connecting the Projector ..................11
Connect to Computer/Notebook ........11
Connect to Video Sources .................12
Powering the Projector On / Off ........13
Powering On the Projector .................13
Powering off the projector  ..................14
Warning Indicator ...............................14
Adjusting the Projected Image  ..........15
Adjusting the Projector’s Height ........15
Adjusting the Projector’s Zoom /  Focus  .................................................16
Adjusting Projection Image Size ........16
User Controls  ................................18
Control Panel & Remote Control ......18
Control Panel .....................................18
Remote Control Battery Installation ...19
Remote Control ..................................20
On-screen Display Menus  ................24
How to operate ..................................24
Menu Tree ..........................................25
IMAGE  ...............................................27
IMAGE | Advanced  ............................29
IMAGE | Advanced | Signal (RGB)  ...31
DISPLAY ............................................32
DISPLAY | 3D   ...................................35
SETUP ...............................................36
SETUP | Security  ...............................38
SETUP | Audio Settings .....................40
SETUP | Advanced  ............................41
OPTIONS ...........................................42
OPTIONS | Advanced  ........................44
OPTIONS | Lamp Settings .................45
OPTIONS | Optional Filter Settings  ...46
Appendices ....................................47
Troubleshooting  ................................47
Replacing the Lamp ..........................53
Installing and Cleaning the  Dust Filter  .........................................55
Compatibility Modes .........................56
Computer/Video/HDMI/Mac  Compatibility ......................................56
3D Input Video Compatibility  .............57
RS232 Commands and Protocol  Function List  .....................................58
RS232 Pin Assignments ....................58
RS232 Protocol Function List  ............59
Ceiling Mount Installation ..................63
Optoma Global Offices  .....................64
Regulation & Safety Notices .............66
Table of Contents 
						

							2English
Usage Notice
Safety Information
The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous \
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limitsThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Important Safety Instruction  1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation.  As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow.  2. Do not use the projector near water or moisture. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture.  3. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat.  4. Clean only with dry cloth.  5.  Only use attachments/accessories specified by the manufacturer.   6. Do not use the unit if it has been physically damaged or abused.  Physical damage/abuse would be (but not limited to): Unit has been dropped. Power supply cord or plug has been damaged. Liquid has been spilled on to the projector. Projector has been exposed to rain or moisture. Something has fallen in the projector or something is loose inside.Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair.  7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock.  8. See projector enclosure for safety related markings.  9. The unit should only be repaired by appropriate service personnel.   
						

							3English
Usage Notice
Precautions
 
Please follow all warnings, precautions and 
maintenance as recommended in this user’s 
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt and damage your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not 
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as 
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to 
cool down. Follow instructions as described on pages 
53-54.
▀■ Warning- This projector will detect the life of the lamp itself. 
Please be sure to change the lamp when it shows 
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen 
display “OPTIONS | Lamp Settings” menu after 
replacing the lamp module (refer to page 45).
▀■ Warning- When switching the projector off, please ensure 
the cooling cycle has been completed before 
disconnecting power. Allow 90 seconds for the 
projector to cool down.
▀■ Warning- Do not use lens cap when projector is in operation.
▀■ Warning- When the lamp is approaching the end of its lifetime, 
the message “Lamp Warning: Lamp life exceeded.” 
will show on the screen. Please contact your local 
reseller or service center to change the lamp as soon 
as possible.
	When the lamp reaches the end of its life, the pro-jector will not turn back on until the lamp module has been replaced. 
To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages 53-54.  
						

							4English
Usage Notice
Do:
		Turn off and unplug the power plug from the AC outlet before 
cleaning the product.
		Use a soft dry cloth with mild detergent to clean the display 
housing.
		Disconnect the power plug from AC outlet if the product is 
not being used for a long period of time.
Do not:
		Block the slots and openings on the unit provided for 
ventilation.
		Use abrasive cleaners, waxes or solvents to clean the unit.
		Use under the following conditions:
  - In extremely hot, cold or humid environments.
 Ensure that the ambient room temperature is within 
5 - 40°C.
 Relative Humidity is 5 - 40°C, 80% (Max.), 
non-condensing.
    - In areas susceptible to excessive dust and dirt.
   - Near any appliance generating a strong magnetic field.
   - In direct sunlight.  
						

							5English
Usage Notice
Eye Safety Warnings
 
▀■ Avoid staring/facing directly into the projector beam at all 
times. Keep your back to the beam as much as possible.
▀■ When projector is used in a classroom, adequately supervise 
students when they are asked to point out something on the 
screen.
▀■ In order to minimize the lamp power, use room blinds to 
reduce ambient light levels. 
Product Features
▀■ SVGA (800x600) / XGA (1024x768) / WXGA 
(1280X800) Native resolution
▀■ HD compatible – 720p and 1080p supported 
▀■ BrilliantColorTM Technology 
▀■ Kensington Lock 
▀■ RS232 control 
▀■ Rapid shutdown 
▀■ Full 3D(*) (See page 57)
▀■ The Product Features shall be configured by the manu-
facturer as per practical conditions.
(*) For models with  HDMI Input.Product features may  vary depending on model. 
						

							6English
Introduction
Documentation : 
	User’s Manual
	Warranty Card
	Quick Start Card
	WEEE Card   (for EMEA only)
	Due to different applications in each Country, some regions may have different accessories.
Power Cord
IR Remote Control
Package Overview
Unpack and inspect the box contents to ensure 
all parts listed below are in the box. If something 
is missing, please contact your nearest customer 
service center.
Battery
ProjectorVGA Cable(*)
VG A
E nte r
M enu Z
oom
Carrying case(*)
CR2025
3V
	(*) The acces-sory depends on model’s specifica-tions. 
						

							7English
Introduction
Product Overview
Main Unit
 
Focus Ring1. 
Zoom Lever2. 
IR Receiver3. 
Control Panel4. 
Input / Output Connections5. 
Kensington6. TM Lock Port
Ventilation (inlet)7. 
Speaker8. 
Lens Cap9. 
Tilt-Adjustment Feet10. 
Ventilation (outlet)11. 
1
9
	The interface is subject to model’s specifi-cations.
	Do not block projector in/out air vents.
7
11
5
21
3
10
8
4
6 
						

							8English
Introduction
6
12
78
11
Source1. 
Keystone Correction2. 
Enter3. 
Re-Sync4. 
Help5. 
Four Directional Select Keys6. 
Temp LED7. 
Power8. 
On/Standby LED 9. 
Lamp LED 10. 
Menu11. 
Control Panel
5
10
34
9     
						

							9English
Introduction
USBVGA1-IN/YPbPr/
VIDEO
VGA-OUT
VGA2-IN/YPbPr
HDMI
AUDIO1-IN
AUDIO-OUT
AUDIO2-IN
S-VIDEO
RS-232C
Input/Output Connections
Composite Video Input Connector1. 
S-Video Input Connector2. 
VGA-Out Connector (Monitor Loop-through Output)3. 
VGA2-IN/YPbPr Connector  4. 
(PC Analog Signal/Component Video Input/HDTV/YPbPr)
VGA1-IN/YPbPr/5.   Connector  
(PC Analog Signal/Component Video Input/HDTV/YPbPr/
Wireless function via VGA Dongle)
HDMI Connector 6. (*)
Security Lock Slot7. 
Audio2 Input 8. Connector (3.5mm mini jack)
Audio Output Connector ( 3.5mm mini jack)9. 
Audio1 Input Connector (3.5mm mini jack)10. 
RS-232 Connector (9-pin)11. 
USB Connector (Connect to PC for Remote Mouse func-12. 
tion/USB Service for firmware upgrade)
Power Socket13. 
Monitor loop  through only sup-port in VGA1-IN/YPbPr.The interface is  subject to model’s specifications.VGA dongle is a  optional accesso-ry. Please contact  Optoma service for details.
(*) for optional.  Remote mouse  requires special remote.
79101112138
234516 
						

							10English
Introduction
Remote Control
	The interface is subject to model’s specifications.Source1. 
Re-Sync2. 
Video and S-Video 3. 
HDMI4. 
3D5. 
Volume +/-6. 
Four Directional Select 7. 
Keys
Menu8. 
AV Mute9. 
Mute10. 
IR LED Indicator11. 
Power On/Off12. 
VGA13. 
Keystone +/-14. 
Aspect15. 
Enter16. 
Zoom17. 
Brightness Mode18. 
VG A
E nte r
M enu Z
oom
3VOLTSCR2025
Before using the  remote control for the first time, remove the trans-parent insulation tape. See page 19 for battery installation.
12
13
15
14
7
10
9
8
4
5
3
2
1
11
66
17
16
18
14