Optoma Hd803 Projector User Manual
Have a look at the manual Optoma Hd803 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1077 Optoma manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 37
English
37
Appendices
6. Select the “Change” button under the “Monitor” tab.
7. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 x 1200). (*)
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the comput-
er.
2. Press the toggle output settings. Example: [Fn]+[F4]...](http://img.usermanuals.tech/thumb/3621/93781/w64_optoma-hd803-manual_d-36.png "Page 37
English
37
Appendices
6. Select the “Change” button under the “Monitor” tab.
7. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 x 1200). (*)
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the comput-
er.
2. Press the toggle output settings. Example: [Fn]+[F4]...")
English 41 Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. Warning: Lamp com-partment is hot! Allow it to cool down before changing lamp! Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. 3 2 4 Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power button. 2. Allow the projector to cool down at least 30 minutes. 3. Disconnect the power cord. 4. Use a screwdriver to remove the screw from the cover. 5. Push up and remove the cover. 6. Remove the 2 screws from the lamp module. 7. Pull out the lamp module. To replace the lamp module, reverse the previous steps. 8. Turn on the projector and do “Lamp Reset” after the lamp module is replaced. Lamp Reset: (i)Press “Menu” -> (ii)Select “System” -> (iii)Select “Lamp setting” ->(iv)Select “Lamp reset” -> (v)Select “Yes”. 1
42 Appendices Remark : “*”com-pressed computer image. Compatibility Modes NoteNote ModeResolutionV.Frequency (Hz) AAnalogDigital VESA SVGA800 x 60060 VESA SVGA800 x 60072 VESA SVGA800 x 60075 VESA XGA1024 x 76860 VESA XGA1024 x 76870 VESA XGA1024 x 76875 VESA XGA1024 x 76885 VESA WXGA1280 x 72060 VESA WXGA1280 x 76860 VESA WXGA1280 x 76872 VESA WXGA1280 x 76885 HD1280 x 72060 HD1280 x 72072 VESA SXGA+1400 x 120060 VESA UXGA1600 x 120060 * HD1920 x 108024 * HD1920 x 108060 * MAC1152 x 87075.06 MAC G4640 x 48060 MAC G41024 x 76875
English 43 Appendices RS232 Commands and Protocol Function List Pin no.NameI/O (From Projector Side 1NC__ 2RXDIN 3TXDOUT 4NC__ 5GND__ 6NC__ 7NC__ 8NC__ 9NC__ RS232 Pin Assignments 351 96
44 Appendices RS232 Protocol Function List Interface: 9 wires RS-232CBaud Rate: 115200 Data Bit: 8Parity: noneStop Bits: 1Flow Control: none Terminatro 1Terminator 2Silence/OSD Modeset/get Viewed AsFunction DescriptionACKOKOKOKOKOK--sPower OnDefault ACK Comand Header BlankBlankAddress CodeCommandBlankTerminator 1HeaderTerminator 2Silence/OSD Modeset/get Viewed AsFunction DescriptionACK* 0 IR 002 * 0 IR --sPower OffDefault ACK* 0 IR 008 * 0 IROsMenuDefault ACK* 0 IR 009 * 0 IROsUpDefault ACK* 0 IR 010 * 0 IROsDownDefault ACK* 0 IR 011 * 0 IROsRightDefault ACK* 0 IR 012 * 0 IROsLeftDefault ACK* 0 IR 013 * 0 IROsEnterDefault ACK* 0 IR 014 * 0 IR --sSourceDefault ACK* 0 IR 015 * 0 IR --sRe-syncDefault ACK* 0 IR 016 * 0 IR --sSource: DVI_DigitalDefault ACK* 0 IR 017 * 0 IR --sSource: HDMI 1Default ACK* 0 IR 018 * 0 IR --sSource: Composite VideoDefault ACK* 0 IR 019 * 0 IR --sSource: S-VideoDefault ACK* 0 IR 020 * 0 IR --sSource : DVI_AnalogDefault ACK* 0 IR 025 * 0 IR --sAspect Ratio 16:9Default ACK* 0 IR 026 * 0 IR --sAspect Ratio 4:3Default ACK* 0 IR 027 * 0 IROsAspect ratio LetterBoxDefault ACK* 0 IR 028 * 0 IROsAspect ratio 1:1Default ACK* 0 IR 030 * 0 IRSsSource Lock OnDefault ACK* 0 IR 031 * 0 IRSsSource Lock OffDefault ACK 002 008 013 014 009 031 028 030 019 COMHB COM 010 011 012 027 025 020 HEADB ADDRB TERM2 SILN 017 026 015 SILN 018 016 Default ACK:"*000
English 45 Appendices Comand HeaderBlankBlankAddress CodeCommandBlankTerminator 1HeaderTerminator 2Silence/OSD Modeset/get Viewed AsFunction DescriptionACK s/g TERM2 TERM1 SILN HEADB ADDRB COMHB COM* 0 IR 035 * 0 IR --sBrightnessDefault ACK* 0 IR 036 * 0 IR --sContrastDefault ACK* 0 IR 037 * 0 IR --sTintDefault ACK* 0 IR 038 * 0 IR --sColorDefault ACK* 0 IR 039 * 0 IR --sImage shift upDefault ACK* 0 IR 040 * 0 IR --sImage shift downDefault ACK* 0 IR 041 * 0 IR --smodeDefault ACK* 0 IR 042 * 0 IR --seage mask(overscan)Default ACK* 0 IR 043 * 0 IR --soverscan(zoom)Default ACK* 0 IR 046 * 0 IROsKeystone shift upDefault ACK* 0 IR 047 * 0 IROskeystone shift downDefault ACK* 0 IR 048 * 0 IROsImage shift leftDefault ACK* 0 IR 049 * 0 IROsImage shift rightDefault ACK* 0 IR 050 * 0 IR --sSource: HDMI 2Default ACK Comand Header BlankBlankAddress CodeCommandBlankTerminatorHeader set/get Viewed AsFunction DescriptionReturnNote* 0 IR 801 * 0 IR --gGet Lamp Hour *002 xxxxxRange of xxxxx is 0 99999 * 0 IR 802 * 0 IR -- gGet Video Source*003 xxxx means 00 : no source 01 : DVI_Digital 02 : HDMI 1 03 : Composite Video 04 : S-Video 05 : DVI_Analog 06 : Component Video 07 : HDMI 2 08 : Testin g * 0 IR 803 * 0 IR --gGet Lamp Status*004 xxxx means 00 : Brite Mode Off 01 : Brtire Mode * 0 IR 804 * 0 IR -- gGet Projector status*005 xxxx means projector is in 00 : Standby mode 01 : Power On 03: Cooling on or cooling off 04: Lamp error 05: Thermal error 050 042 040 041 036 037 038 039 035 802 803 804 043 048 049 046 047 COMHB COM 801 HEADB ADDRB s/g TERM1
46 Appendices Please note that dam-age resulting from incorrect installation will invalidate the war-ranty. Ceiling Mount Installation 1. To prevent damaging your projector, please use the ceil- ing mount package for installation. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attached a mount to the projec- tor met the following specifications: Screw type: M4 Maximum screw length: 10mm Minimum screw length: 8mm Warning: 1. If you buy the ceiling mount from other company, please ensure that there is at least 10cm distance between the bottom cover of the projector and the ceiling.2. Avoid placing the projector near sources of heat such air-conditioning units and heaters otherwise it may overheat and shut down automatically.3. Ceiling mounting shall be mounting on metal or concrete. Min.610.60mm (24.04")/Max.850.60mm (33.49") 410.99mm(16.18") 185.00mm (7.28") 106.00mm (4.17")310.62mm (12.23") 200.00mm(7.87") 100.00mm(3.94") 82.50mm(3.25") (3.25")82.50mm NoteNote
English 47 Appendices Optoma Global Offices For service or support please contact your local office. USA 715 Sycamore DriveTel : 408-383-3700 Milpitas, CA 95035, USAFax: 408-383-3702 www.optomausa.comService : [email protected] Canada 5630 Kennedy Road, Mississauga, ON, L4Z 2A9, CanadaTel : 905-361-2582 www.optoma.caFax: 905-361-2581 Europe 42 Caxton Way, The Watford Business Park Watford, Hertfordshire, WD18 8QZ, UK Tel : +44 (0) 1923 691 800 www.optoma.euFax: +44 (0) 1923 691 888 Service Tel : +44 (0)1923 691865Service : [email protected] France Bâtiment ETel : +33 1 41 46 12 20 81-83 avenue Edouard VaillantFax: +33 1 41 46 94 35 92100 Boulogne Billancourt, FranceService : [email protected] Spain Paseo de la CastellanaTel : +34 91 790 67 01 135 7 Planta+34 91 790 67 02 Madrid, SpainFax: + 34 91 790 68 69 Deutschland Werftstrasse 25Tel : +49 (0) 211 506 6670 D40549 Düsseldorf,Fax: +49 (0) 211 506 66799 GermanyService : [email protected] Scandinavia Grev Wedels Plass 2Tel : +47 32 26 89 90 3015 DrammenFax: +47 32 83 78 98 NorwayService : [email protected] Latin America 715 Sycamore DriveTel : 408-383-3700 Milpitas, CA 95035, USAFax: 408-383-3702 www.optoma.com.brwww.optoma.com.mx
48 Appendices Taiwan 231,台北縣新店市民權路108號5樓 R.O.C.傳真：+886-2-2218-2313 電話：+886-2-2218-2360www.optoma.com.tw 服務處：[email protected] Hong Kong Unit A, 27/F Dragon Centre, 79 Wing Hong Street, Cheung Sha Wan Kowloon, Hong Kong Tel : +852-2396-8968Fax: +852-2370-1222 www.optoma.com.hk China 上海市长宁区凯旋路1205号5楼电话：+86-21-62947376 邮编: 200052传真：+86-21-62947375 www.optoma.com.cn Japan 3-25-18±Ù”Ä·ï»” ¦”¤µŠþÏç E-Mail: [email protected]://www.os-worldwide.com/ Korea WOOMI TECH.CO.,LTD. 4F, Minu Bldg.33-14, Nonhyun-Dong,Tel : +82+2+34430004 Kangnam-Ku, seoul, 135-815, KOREAFax: +82+2+34430005
English 49 Appendices Regulation & safety notices This appendix lists the general notices of your Projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be deter- mined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ▀■ Reorient or relocate the receiving antenna. ▀■ Increase the separation between the device and receiver. ▀■ Connect the device into an outlet on a circuit different from that to which the receiver is connected. ▀■ Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this computer.
50 Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.this device may not cause harmful interference, and 2.this device must accept any interference received, includ-ing interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. Remarque à l’intention des utilisateurs cana- diens Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries ▀■ EMC Directive 89/336/EEC (including amendments) ▀■ Low Voltage Directive 73/23/EEC (amended by 93/68/ EEC) ▀■ R & TTE Directive 1999/EC (if product has RF function) Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.