OKI MB260 User Manual

MB260
- 11 -
Installation
Rules for use symbols
 WARNING
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these notes. Refer to the security notices 
presented in the Safety booklet.
 CAUTION
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read 
these notes. Refer to the security notices presented in the Safety booklet.
 Important
Indicates...

MB260
- 12 -
Installation
Terminal description
Front and Back sides
1. Control panel
2. Paper jam cover
3. Power supply cord connection
4. On/Off switch
5. Slave USB connection (for PC)
6. Master USB connection (USB key)
7. Manual paper feed setup guides8. Manual input tray
9. Paper tray
10. Cartridge access cover
11. Fold-down stopper for paper delivery
12. Paper output
13. Smart card insertion point
Downloaded From ManualsPrinter.com Manuals 

MB260
- 13 -
Installation
Command panel
Accessing terminal menus
All terminal functions and settings are available via the menu and are associated to a specific menu command.  
For example, the menu command 51 launches the printing of the functions list (the functions list stores the list of all 
terminal menus, sub-menus and their identification number). 
Two methods are available to access menu items: the step by step method or the shortcut method.
To print the functions list with the Step by step...

MB260
- 14 -
Installation
Packaging contents
The packaging contains the items listed below:
Multifunction device
1 toner cartridge
1 Installation guide 
1 PC installation CD ROM and 1 OCR PC software CD 
ROM (depending on model)
2 booklets (safety and warranty) 
1 power cord
Device installation
1Unpack the device.
2Install the device respecting the security notices 
stated at the beginning of this booklet.
3Remove all stickers from the machine.
4Remove the plastic protection film from the screen.
Feed...

MB260
- 15 -
Installation
3Setup the back side feed cassette stop by pushing 
the PUSH lever (A). 
Then adjust the lateral paper guides to the paper 
format by pushing lever (B) located on the left 
guide. Adjust the length paper guide to the paper 
format by pushing lever (C).
4Take a paper stack, pull the paper off and align it 
on a flat surface.
5Put the paper stack in the feed cassette 
(200 sheets of 80 g/m² paper for instance).
6Put the feed cassette back in its location.
Cartridge installation...

MB260
- 16 -
Installation
Starting your device
Device connection
1Make sure that the On/Off switch is on Off 
(O position). 
2Connect the power cord to the device.  
Plug the power cord to outlet on the wall. 
3Press the On/Off button to turn on the device 
(I position).
Device initial setup
After a few seconds, when the machine has warmed up, 
the Easy Install function is launched and the LCD screen 
displays the following message:
The Easy Install function will help you configure your 
machine by...

MB260
- 17 -
Installation
appear on the reverse side.
• Set envelope by pressing the folding line of four edges 
properly after releasing air inside.
• Set envelope in a proper position after aligning in case 
it is bent or warped.
• Paper conditioning is not allowed. And it should be 
used under normal office environment.
Downloaded From ManualsPrinter.com Manuals 

MB260
- 18 -
Copy
Copy
Your machine has the function to make one or more 
copies.
You can also set up several parameters in order to make 
copies at your will.
Simple copy
In this case, the default parameters are applied.
1Place the document to be copied face down on the 
glass, respecting the indications around the glass.
2Press the   button twice. The copy is made 
using the default parameters.
ECO mode copy
The ECO mode enables you to reduce the amount of 
toner consumed on the page so as to save your...

MB260
- 19 -
Copy
2Enter the desired number of copies and confirm 
with the OK button.
3Choose the paper tray AUTOMATIC or MANUAL
with the buttons  or !, then confirm with the OK
button.
4Choose the copying option ID CARD with the 
buttons  or ! and confirm with the OK button.
5Choose the resolution depending on the desired 
printing quality AUTO, TEXT, QUALITY TEXT or 
PHOTO with the buttons  or !, then confirm with 
the OK button. For optimal results with ID 
documents, select the PHOTO resolution....

MB260
- 20 -
Copy
Analysis origin setup
If you want, you can change the origin of the scanner.
By entering new values for X and Y in mm (X < 209 and 
Y < 280), you move the analysed area as shown on the 
diagram below.
! 843 - ADVANCED FCT/COPY/ORIGIN
1Press !, enter 843 using the keypad.
2Select the X and Y coordinates with the buttons 
or !.
3Setup the desired coordinates with the numerical 
keypad or the buttons  and !.
4Confirm your choice by pressing the OK button.
5Quit this menu by pressing the...