OKI C9650hdn User Manual

C9650 User’s Guide> 31
5.Gently push the tray back into the printer.
USING THE MP TRAY
1.Squeeze the handle (1) and open the multi-purpose tray. 
1
Downloaded From ManualsPrinter.com Manuals 

C9650 User’s Guide> 32
2.Fold out the paper support section and swivel out the 
extension supports (2).
3.Adjust the paper guides (3) to the size of the paper being 
used.
4.Fan the paper to be loaded then tap the edges of the stack on 
a flat surface to make it flush.
5.Load the paper.
• For single-sided printing on letterhead, load the paper into 
the multi-purpose tray with pre-printed side up and top 
edge into the printer.
• For two-sided (duplex) printing on letterhead, load the 
paper with...

C9650 User’s Guide> 33
the printer. (The duplex unit must be installed for this 
function.)
• Envelopes should be loaded face-up with long edge into 
the printer. Do not select duplex printing on envelopes.
• Do not leave space between the paper and the guides.
• Do not exceed the paper capacity of approximately 230 
sheets, 100 transparencies or 25 envelopes. Maximum 
stacking depth is 1 in.
Downloaded From ManualsPrinter.com Manuals 

C9650 User’s Guide> 34
USING THE STACKERS
Face-down stacker
When the face-up stacker (1) on the left side of the printer is closed 
(its normal position), paper is ejected to the face-down stacker on 
the top of the printer.
Face-up stacker
The face-up exit path is used for heavy paper (cardstock etc.), 
envelopes, transparencies, and labels.
1.Open the stacker (1).
1
1
Downloaded From ManualsPrinter.com Manuals 

C9650 User’s Guide> 35
2.Flip out the paper support (2).
3.Swivel out the paper support extension (3).
2
3
Downloaded From ManualsPrinter.com Manuals 

C9650 User’s Guide> 36
CONTROL PANEL
The control panel can be swivelled to 90° (maximum) upwards from 
its base position (1) as required for ease of use.
BUTTONS AND LIGHTS
The parts of the control panel are identified and briefly explained 
below:
1. Shutdown/Restart button
Hold down for more than 2 seconds for a soft shutdown. You 
can then press this button again for a restart or use the 
Power switch to turn off the printer completely.
1
Downloaded From ManualsPrinter.com Manuals 

C9650 User’s Guide> 37
2. Ready light
On: indicates ready to print
Flashing: indicates processing print data
Off: indicates unable to receive data (offline)
3. Attention light
Off: indicates normal operation
Flashing: indicates error(s) present but printing can continue
On: indicates error(s) present and printing cannot continue
4. Display panel
Displays status and setup information for the printer and user 
help information in your chosen language
5. Up-arrow button
Enters menu mode and enables upward...

C9650 User’s Guide> 38
DISPLAY PANEL MESSAGES
There are four types of display panel message:
>Status information
>Menu (functions) information
>Configuration information
>Help information
STATUS INFORMATION
Status information is associated with three printer states:
In the Information state, such as idling or printing, the printer 
is able to process print jobs.
In the Warning state, the printer has encountered some minor 
problem but is still able to process print jobs.
In the Error state, the printer...

C9650 User’s Guide> 39
Restart). Available to support staff to allow printer 
configurations and special functions to be set.
CONFIGURATION INFORMATION
Configuration information displays printer configuration 
information such as internal firmware versions.
Menu options at each level can be scrolled through by moving the 
highlight with the Up-arrow/Down-arrow buttons and a 
highlighted option at that level can be selected by pressing the 
Enter button. When the lowest level menu has been selected, you...

C9650 User’s Guide> 40
The steps involved in using the menus are typically as follows:
1.Ensure that the display panel indicates that the printer is 
ready to print.
2.Enter User menu mode by pressing either the Enter button 
or the Up-arrow or Down-arrow button and press the 
latter two repeatedly until the desired menu is highlighted in 
the displayed list.
3.Press the Enter button to select this menu.
4.Press the Up-arrow or Down-arrow buttons repeatedly 
until the desired Item is highlighted.
5.Press...