OKI C710n User Manual

							81 – C710n User’s Guide
2.Note the positions of the four toner cartridges (a) and image 
drums (b). It is essential that they go back in the same order.
a
b
Downloaded From ManualsPrinter.com Manuals 
						

							82 – C710n User’s Guide
3.Holding it by its top centre, lift the image drum, complete 
with its toner cartridge, up and out of the printer.
4.Put the assembly down gently onto a piece of paper to 
prevent toner from marking your furniture and to avoid 
damaging the green drum surface.
CAUTION!
The green image drum surface at the base of the ID 
unit is very delicate and light sensitive. Do not touch it 
and do not expose it to normal room light for more 
than 5 minutes. If the drum unit needs to be out of the 
printer for longer than this, please wrap the cartridge 
inside a black plastic bag to keep it away from light. 
Never expose the drum to direct sunlight or very 
bright room lighting.
Downloaded From ManualsPrinter.com Manuals 
						

							83 – C710n User’s Guide
5.With the colored toner release lever (1) to the right, pull the 
lever towards you. This will release the bond between the 
toner cartridge and the image drum unit.
6.Lift the right-hand end of the toner cartridge (1) and then draw 
the cartridge to the right to release the left-hand end as 
shown (2), and 
withdraw the toner cartridge out of the image drum 
cartridge. Place the cartridge on a piece of paper to avoid marking your 
furniture.
7.Take the new image drum cartridge out of its packaging and 
place it on the piece of paper where the old cartridge was 
placed. Keep it the same way round as the old unit. Pack the 
old cartridge inside the packaging material for disposal.
Note:
Follow instructions that come with the new image drum 
for additional information such as the removal of 
packaging material etc.
1
2
1
Downloaded From ManualsPrinter.com Manuals 
						

							84 – C710n User’s Guide
8.Place the toner cartridge onto the new image drum cartridge 
as shown. Push the left end in first, and then lower the right 
end in. (It is not necessary to fit a new toner cartridge at this 
time unless the remaining toner level is very low.)
9.Push the colored release lever away from you to lock the 
toner cartridge onto the new image drum unit and release 
toner into it.
2
1
Downloaded From ManualsPrinter.com Manuals 
						

							85 – C710n User’s Guide
10.Holding the complete assembly by its top centre, lower it into 
place in the printer, locating the pegs at each end into their 
slots in the sides of the printer cavity.
11.Finally, close the top cover and press down firmly at both 
sides so that the cover latches closed.
Replacing the Transfer Belt Unit ____
The belt unit is located under the four image drums. This unit 
requires replacement approximately every 60,000 pages.
Switch off the printer and allow the fuser to cool for about 
10 minutes before opening the cover.
Note:
If you need to return or transport your printer for any 
reason, please make sure you remove the image drum 
unit beforehand and place in the bag provided. This is to 
avoid toner spillage.
Downloaded From ManualsPrinter.com Manuals 
						

							86 – C710n User’s Guide
1.Press the cover release and open the printer’s top cover 
fully.
2.Note the positions of the four toner cartridges (a) and image 
drums (b). It is e
ssential that they go back in the same order. 
WARNING!
If the printer has been powered on, the fuser will be 
hot. This area is clearly labelled. Do not touch.
a
b
Downloaded From ManualsPrinter.com Manuals 
						

							87 – C710n User’s Guide
3.Lift each of the image drum units out of the printer and place 
them in a safe place away from direct sources of heat and 
light.
CAUTION!
The green image drum surface at the base of each 
cartridge is very delicate and light sensitive. Do not 
touch it and do not expose it to normal room light for 
more than 5 minutes. If the drum unit needs to be out 
of the printer for longer than this, please wrap the 
cartridge inside a black plastic bag to keep it away 
from light. Never expose the drum to direct sunlight or 
very bright room lighting.
Downloaded From ManualsPrinter.com Manuals 
						

							88 – C710n User’s Guide
4.Locate the two fasteners (a) at each side of the belt and the lifting 
bar
 (b) at the front end.
5.Turn the two fasteners 90° to the left. This will release the 
belt from the printer chassis.
6.Pull the lifting bar (b) upwards so that the belt tilts up towards the 
front, and withdraw the belt unit (c) from the printer.
7.Lower the new belt unit into place, with the lifting bar at the 
front and the drive gear towards the rear of the printer. 
Locate the drive gear into the gear inside the printer by the 
a a
b
c
Downloaded From ManualsPrinter.com Manuals 
						

							89 – C710n User’s Guide
rear left corner of the unit, and lower the belt unit flat inside 
the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							90 – C710n User’s Guide
8.Turn the two fasteners (a) 90° to the right until they lock. This will 
secure the belt unit in place.
9.Replace the four image drums, complete with their toner 
cartridges, into the printer in the same sequence as they 
came out: cyan (nearest the rear), magenta, yellow and 
black (nearest the front).
10.Finally, close the top cover and press down firmly at both 
sides so that the cover latches closed.
a
a
Downloaded From ManualsPrinter.com Manuals